KitchenAid Dishwasher Hardware

KitchenAid Appliance Parts
Shop By Part Type

Popular KitchenAid Dishwasher Hardware

Your Price
$10.52
  In Stock
Wash Arm Retainer Nut
★★★★★
★★★★★
18 Reviews
PartSelect Number PS11747063
Manufacturer Part Number WP9742945
Use this part to secure the lower spray arm of your dishwasher.
Fixes these symptoms
  • Leaking
  • Noisy
  • Not cleaning dishes properly
  • See more...
Installation Instructions
Kent from Matthews, NC
Water washing out under front door onto floor
The plastic parts on this spray arm assembly wear with time and the rotation wobble effect creates a wave action in the pool of water at the bottom of the dishwasher. This waves the water onto the front door and forces a leak outside the unit. Replace the lower arm assembly, washer, bearing and nut. They all wear. Also remember to tighten the screws on top of the pump assembly. They loosen and aid in the wobble. Good Luck! Read more...
Your Price
$7.68
  In Stock
Rubber Washer
PartSelect Number PS11743934
Manufacturer Part Number WP717273
The rubber washer is a part which is specific to dishwashers and should not be substituted by a similar part. It works with the heating element to seal the receptacle opening where the heating element is attached. The rubber washer is used to prevent water leaking from your dishwasher during its cycle. Before making any repairs to your dishwasher make sure that you disconnect the power by finding the breaker for the dishwasher, and turning it off. The tools you will need to complete this repair include an adjustable wrench, and a 1/4 inch nut driver. This specific rubber washer is sold individually.
Fixes these symptoms
  • Leaking
  • Not cleaning dishes properly
  • Not drying dishes properly
  • See more...
Installation Instructions
PAUL from ESTES PARK, CO
Unit Wouldn't Work. "Clean" Light Blinking
The unit had power, but the controls would not work. The "clean" light was blinking. I first replaced the control unit, no help. I then used the "just ask" and was told the problem was the heating element and/or the hi-temp thermostat. I replaced both those and used the re-set code pushing the "hi-temp/air dry, hi-temp/air dry" buttons. That did it. Easy parts to locate and replace. It took longer pulling the unit out and putting it back than it did to replace the parts. Read more...
Your Price
$7.16
  In Stock
Retainer Clip - White
★★★★★
★★★★★
13 Reviews
PartSelect Number PS11755737
Manufacturer Part Number WPW10503549
This part is used to hold the access panel in place. Sold individually.
Installation Instructions
Todd from ROTONDA WEST, FL
A plastic retainer pin for the bottom kick panel was missing.
simply line up the new pin with the rectangular slot in the kick panel and metal panel behind, slide the pin in and turn it with a flat blade screw driver.
NOTE: the original pin was black. A black replacement part cost $29 plus shipping! A knock-off pin was only $6 plus shipping. I got the cheap one and colored it with a black Sharpee marker before installation.
Read more...
Your Price
$13.56
  In Stock
CLIP
★★★★★
★★★★★
9 Reviews
PartSelect Number PS11770115
Manufacturer Part Number W10919676
Your Price
$26.48
  In Stock
Retainer Clip - Black
★★★★★
★★★★★
16 Reviews
PartSelect Number PS11755736
Manufacturer Part Number WPW10503548
This part is used to hold the access panel in place. Sold individually.
Installation Instructions
Susan from WESTON, FL
Rinse Aid Cap
I ordered the cap for my kitchen aid dishwasher and it is too small. Read more...
Your Price
$4.27
  In Stock
Screw
PartSelect Number PS11743743
Manufacturer Part Number WP681249
Sold individually.
Your Price
$31.35
  In Stock
Grommet
★★★★★
★★★★★
6 Reviews
PartSelect Number PS11756098
Manufacturer Part Number WPW10538166
Fixes these symptoms
Installation Instructions
Monica from PITTSFORD, NY
WARNING!!! This is NOT the grommet that goes on the "pump stem" in the center
I purchased this misguided by the official response to "Doug" on April 17, 2018, which at the time was labeled as "most helpful". This is NOT the little grommet in the center. This is a big grommet that goes no the supply pump. This is #14 in the diagram. (#15 is actually the clamp that holds it). If you are looking for the little grommet that goes on that stem on the central recirculation pump, that part is not available, it only comes fused on the sump, and for replacing the sump you have to disassemble the whole bottom part of the dishwasher, pumps, sensors, valves, hose...even this big grommet. A lot of work, and since you are at it, you might want to replace both grommets. If you need THIS big grommet (#14) only, then it is not so much work, just take out one clamp, one connected cable, and the grommet to replace. But check if your machine has reusable clamps, because if not, you might want to order a new clamp. Good luck! Read more...
Your Price
$7.68
  In Stock
Hose Clamp
★★★★★
★★★★★
1 Review
PartSelect Number PS11743008
Manufacturer Part Number WP596669
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This clamp is used to securely attach a hose to another part of your appliance, which helps prevent leaks from those connections. Depending on the appliance, it can attach hoses to drain pumps, water inlet valves, pressure switches, and injector nozzles. We recommend you refer to model-specific diagrams for appropriate uses and exact placement. This hose clamp is made of metal, and is sold individually. To access and replace this part you will need a nut driver, pliers, and screwdrivers. Before you begin any repair work, make sure you have unplugged your appliance, and shut off the water supply if applicable.
Fixes these symptoms
Installation Instructions
jeff from lindenhurst, IL
Washing Machine was leaking water
Loosened the hose clamp, removed the injector valve and injector nozzle assembly, replaced both and tightened with new hose clamp. Fixed the problem for less than $20!! Washing machine is 20 years old and this was the first problem--hopefully it is now good for another 20 years! Read more...
Your Price
$7.68
  In Stock
Screw, 8/18 x 3/8
★★★★★
★★★★★
2 Reviews
PartSelect Number PS11746840
Manufacturer Part Number WP90767
This screw is sold individually.
Installation Instructions
Alexander from Lakeland, FL
Broken Dryer Knob
First let me just say that Partselect.com is now one my stored favorites in my web browser. I came home from a business trip and saw a pair of pliers on the dryer. I thought that was odd until my wife informed me that the knob on the dryer had broken. So she was using the pliers to select the cycle. Somehow she knew where the missing pointer was actually pointing. Since the dryer was over 5 years old I saw this as an opportunity to upgrade both appliances. Not with my frugal wife. A search of the Internet popped up partselect. I ordered Wednesday morning and the parts where on my doorstep late Thursday. Trust me I was very surprised. Everything worked perfectly. Two thumbs up!!! Read more...
Your Price
$7.76
  In Stock
Screw - 8-18 x 1/2
PartSelect Number PS11740645
Manufacturer Part Number WP302868
Sold Individually.
Installation Instructions
Margaret from San Diego, CA
Wanted to change beige dishwasher front to black.
First , I went outside and turned the breaker for the dishwasher off. Next,I removed the screws that held the bottom 2 pieces, that rest on the floo,r in place. Then removed the two beige metal pcs. . Next I replaced them with the 2 black pieces I had ordered and secured them with the 2 black screws I had received as part of my order. Then I removed the scews from the inside of the door of my KitchenAid Dishwasher. This released both the front bottom panel and the control panel. . I took the beige bottom door panel off and moved the insulation piece from the back of thebeige panel to the back of the black panel. Then I intalled the new black panel I ordered and resecured it with two screws until I had finished with the control panel switch out.
I had to unplug an electronic tape from the inside of the beige control panel and plug the same tape back into the black control panel. I also had to remove the beige handle that was on the inside of the control panel, attached to the door, and replace it with the new black one I'd received. I then installed the black control panel and reattached it with screws and finished replacing the rest of the screws I had removed from the inside of the door.
I tested the handle to make sure it opened the door and locked it like it should and then went outside and turned the breaker back on. Came in and turned on the dishwasher and did a load of dishes. It looks awesome, matches the rest of my black appliances and I am very proud to have done it myself. I also wanted to thank the customer service lady who was so great to work with on the phone. I would shop with you again.
Read more...

Related Parts