KitchenAid Dishwasher Brackets and Flanges

Videos!

Your Price

$10.04

KitchenAid Dishwasher Mounting Bracket

★★★★★

13 Reviews

PartSelect Number PS11745496

Manufacturer Part Number WP8269145

The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking, or tilting forward. The bracket is made entirely of metal. It is recommended to check all brackets, if applicable, because they often wear at the same rate and both may need to be replaced. This is an OEM part that is sourced from the authentic manufacturer. Tools needed are a pair of needle nose pliers and a screwdriver.

Fixes these symptoms

Door latch failure
Door won’t close
Leaking
See more...

Installation Instructions

Judith from Essex, MA

Lost dishwasher brackets

I called an experienced plumber, who balanced and installed my new dishwasher properly, using the brackets I ordered from Parts Select, after an INEXPERIENCED plumber had tossed the factory-provided mounting brackets out with the shipping carton. Relief! Read more...

Videos!

Your Price

$18.65

KitchenAid Dishwasher Side Mounting Bracket Kit

★★★★★

7 Reviews

PartSelect Number PS1487167

Manufacturer Part Number 8212560

This mounting kit can be used on solid surface countertops.

Your Price

$22.22

KitchenAid Dishwasher BRACKET

★★★★★

2 Reviews

PartSelect Number PS11727941

Manufacturer Part Number W10837623

Your Price

$11.10

KitchenAid Dishwasher Mounting Bracket

★★★★★

2 Reviews

PartSelect Number PS11747051

Manufacturer Part Number WP9741251

This metallic mounting bracket comes with a screw for easy mounting.

Installation Instructions

DAVID from MAPLE GROVE, MN

Dishwasher would only partially fill with water.

First turn off the power and water. Water valve is under the sink. I removed the two lower panels with 5/16 nut driver. I disconnected the valve from the cross member, again with a 5/16 socket. I removed that cross member with the same nut driver. I disconnected the rubber hose using pliers. I unplugged the electrical connector from the valve body. I held the water inlet pipe with a wrench and twisted the valve off with the adjustable pliers. I applied teflon tape to the water inlet pipe and reassembled. Works like new.

For the rubber water tube I pulled off the old tube, put some dish soap on the new tube and it slid right on. Read more...

Videos!

Your Price

$27.73

KitchenAid Dishwasher Middle Wash Arm Tube Holder

PartSelect Number PS11741346

Manufacturer Part Number WP3378186

This holder should have a split in the ring at 3 o'clock position.

Fixes these symptoms

Leaking
Not cleaning dishes properly
See more...

Installation Instructions

Laura from Marietta, GA

The original, detachable hose portion developed a hole and needed replacement

Pretty simple. Hardest part was working the end clips of the slide to remove top rack. You simply need to squeeze the plastic clip in to slide it out. Once the top rack is out, it was an obvious philips head screw removal and new part replacement. Read more...

Your Price

$20.20

KitchenAid Dishwasher Dispenser Mounting Bracket

PartSelect Number PS11755103

Manufacturer Part Number WPW10462232

Fixes these symptoms

Leaking
Will not dispense detergent
See more...

Your Price

$15.73

KitchenAid Dishwasher Spray Arm Tube Hanger

★★★★★

1 Review

PartSelect Number PS11745439

Manufacturer Part Number WP8268349

Fixes these symptoms

Not cleaning dishes properly
See more...

Installation Instructions

Gifford from Holyoke, MA

BOM bracket broken at bottom of alignment hole.

Remove old bracket by prying off clips on rack wires. Squeeze bracket at clips and let it drop.
Under rack, align tube thru new bracket hole. Light squeeze top of new bkt.to clear wire rack. Come straight up aligning squeezed ends thru wire rack. One side at a time, keeping clips above seating area, install one side at a time with light pressure. Read more...