My Orders
KitchenAid Dishwasher Valves
GET YOUR OFFICIAL KitchenAid PARTS TO ENSURE VICTORY
Popular KitchenAid Dishwasher Valves
This water inlet valve should be located behind the lower kick plate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
This water inlet valve should be located behind the lower kick plate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
Installation Instructions
Melissa from AIKEN, SC
Inlet valve wasn't working
Put thread tape on threads. Screwed water hose to part. Pushed hose onto part. Pushed electric clip to part. Screwed part onto washer. Done
The water inlet valve assembly is a crucial component of dishwashers that controls the flow of water into the unit. This genuine OEM replacement part includes the inlet valve, inlet hose, and hose clamp to ensure the proper water supply for your dishwasher’s operation. Designed for specific models, this part ensures that water is fed into the dishwasher during the wash cycle, promoting efficient cleaning. Before installation, it is important to unplug the dishwasher and turn off the water supply to avoid any accidents. Wear work gloves for your safety during the installation process. Be sure to verify the compatibility with your dishwasher’s model number, as similar-looking parts may have slight variations in size or design.
The water inlet valve assembly is a crucial component of dishwashers that controls the flow of water into the unit. This genuine OEM replacement part includes the inlet valve, inlet hose, and hose clamp to ensure the proper water supply for your dishwasher’s operation. Designed for specific models, this part ensures that water is fed into the dishwasher during the wash cycle, promoting efficient cleaning. Before installation, it is important to unplug the dishwasher and turn off the water supply to avoid any accidents. Wear work gloves for your safety during the installation process. Be sure to verify the compatibility with your dishwasher’s model number, as similar-looking parts may have slight variations in size or design.
Installation Instructions
Joseph from BIRMINGHAM, MI
Inlet valve leaking at water connection
The valve has a plastic fitting to attach the the water line with a hose fitting. Was not carful enough with the original and damaged it attaching the water line. Ordered a replacement fitting. While it is possible to replace the water inlet valve without pulling the dishwasher out from the cabinet found it was easier to get at with the m
... Read more
achine out. The video does and good job of showing the removal and replacing the valve. Easy job, don't be like me and be careful attaching the water line.
Read less
This dishwasher water inlet valve regulates the flow of water into the appliance during each cycle, helping ensure proper filling and efficient operation. If your dishwasher is leaking, overfilling, or not filling at all, this component may need to be replaced. Designed for compatibility with a wide range of models, it offers reliable performance and a secure fit. To ensure the correct part, always verify your dishwasher’s model number before ordering, as similar-looking parts may vary in size or shape. Before installation, disconnect the appliance from its power source and wear protective gloves for safety.
This dishwasher water inlet valve regulates the flow of water into the appliance during each cycle, helping ensure proper filling and efficient operation. If your dishwasher is leaking, overfilling, or not filling at all, this component may need to be replaced. Designed for compatibility with a wide range of models, it offers reliable performance and a secure fit. To ensure the correct part, always verify your dishwasher’s model number before ordering, as similar-looking parts may vary in size or shape. Before installation, disconnect the appliance from its power source and wear protective gloves for safety.
Installation Instructions
Robert from E GRAND FORKS, MN
High pitched noise when the washer filled at the beginning of the cycle.
Watched the video, it went as advertised. Easy repair and the noise is gone.
This dishwasher water inlet valve is a single-coil solenoid component responsible for regulating the flow of water into the appliance. It ensures the correct amount of water is delivered during each cycle, supporting optimal cleaning performance and preventing issues such as underfilling, overfilling, or leaks. By electronically opening and closing based on the cycle’s requirements, the valve helps maintain proper water pressure and temperature balance. Replacing a faulty valve can resolve symptoms like the dishwasher not filling, leaking, or failing to clean effectively. This component is engineered for durability and consistent operation.
This dishwasher water inlet valve is a single-coil solenoid component responsible for regulating the flow of water into the appliance. It ensures the correct amount of water is delivered during each cycle, supporting optimal cleaning performance and preventing issues such as underfilling, overfilling, or leaks. By electronically opening and closing based on the cycle’s requirements, the valve helps maintain proper water pressure and temperature balance. Replacing a faulty valve can resolve symptoms like the dishwasher not filling, leaking, or failing to clean effectively. This component is engineered for durability and consistent operation.
Installation Instructions
MICHELLE from EDEN VALLEY, MN
water leaking out of bottom of machine
removes the 1 screw that held the old one in and removed the water lines the supply line with a adjustable wrench and the internal line had a hose clamp on it then i just went in reverse...
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
Installation Instructions
Bruce from GRANDVIEW, MO
washer filled in when off..
replaced the valve
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed. NOTE: As per the manufacture this part has been updated from the original part. It may be a different color, and you may need to order an elbow (# W10685193) for the new designed valve to work.
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed. NOTE: As per the manufacture this part has been updated from the original part. It may be a different color, and you may need to order an elbow (# W10685193) for the new designed valve to work.
Installation Instructions
David from Lexington, NC
Inlet valve was leaking from crack in brass fitting
Removed the lower panels from beneath the dishwasher door. 4 screws. Turned off the water.
Removed one screw holding the inlet valve to the side rail of the dishwasher. It was attached to the hot water line and then the washer water input line. Removed the electrical connector..Pull straight off, and use a pair of pliers to ... Read more open the squeeze clamp on the washer hose. The hot water supply hose has a brass fitting to loosen and remove.
Replaced the inlet valve, reconnected the electrical and also replaced the hot water line from under the sink to the washer. Used a new braided 5' hose with fittings. Used teflon tape on the screws and did not over tighten the brass fittings.
Turned on the hot water supply and checked for leaks. Operated the washer and checked for leaks. Replaced the lower covers.
Removed one screw holding the inlet valve to the side rail of the dishwasher. It was attached to the hot water line and then the washer water input line. Removed the electrical connector..Pull straight off, and use a pair of pliers to ... Read more open the squeeze clamp on the washer hose. The hot water supply hose has a brass fitting to loosen and remove.
Replaced the inlet valve, reconnected the electrical and also replaced the hot water line from under the sink to the washer. Used a new braided 5' hose with fittings. Used teflon tape on the screws and did not over tighten the brass fittings.
Turned on the hot water supply and checked for leaks. Operated the washer and checked for leaks. Replaced the lower covers.
Read less
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoid on the valve will open and close according to the desired amount of water needed.
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoid on the valve will open and close according to the desired amount of water needed.
Installation Instructions
Claudia from Avella, PA
After removing our dishwasher from storage and installing it, the inlet valve was leaking.
After removing the kickplate covers from the bottom front of the dishwasher by removing the 2 screws that attached the covers I determined the inlet valve was leaking, I turned of the water and disconnected the electricity from the dishwasher.
I rolled the dishwasher from under the counter and removed the water supply line from the e ... Read more lbow at the bottom of the dishwasher inlet valve with an adjustable wrench. We then set the dishwasher on its back to gain easy access to the inlet valve.
To remove the inlet valve, Using a philips head screwdriver I removed the one screw holding the bracket and the valve was loose from the dishwasher. Then, two wires were removed from the valve by sliding the clips from the tabs on the valve. The hose that carries the water to the dishwasher was removed by squeezing the clamp with pliers and sliding it onto the hose and pulling the hose from the nipple.
With the valve removed from the dishwasher, the elbow for the supply line can be removed from the bottom of the old valve and installed on the new valve using teflon tape to seal the connection.
The new inlet valve was then installed by reversing the procedure.
Checked to make sure there are no leaks and the dishwasher was good as new.
I rolled the dishwasher from under the counter and removed the water supply line from the e ... Read more lbow at the bottom of the dishwasher inlet valve with an adjustable wrench. We then set the dishwasher on its back to gain easy access to the inlet valve.
To remove the inlet valve, Using a philips head screwdriver I removed the one screw holding the bracket and the valve was loose from the dishwasher. Then, two wires were removed from the valve by sliding the clips from the tabs on the valve. The hose that carries the water to the dishwasher was removed by squeezing the clamp with pliers and sliding it onto the hose and pulling the hose from the nipple.
With the valve removed from the dishwasher, the elbow for the supply line can be removed from the bottom of the old valve and installed on the new valve using teflon tape to seal the connection.
The new inlet valve was then installed by reversing the procedure.
Checked to make sure there are no leaks and the dishwasher was good as new.
Read less
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
Installation Instructions
Lewis from Portsmouth, NH
Dishwasher Not Draining
Ordered both drain & wash impeller kit and the drain check valve with o-ring. Decided to test the cheaper drain check valve first. Pulled dishwasher out from wall & adjacent cabinetry; removed drain hose from disposer and drained as much water as possible; "jacked" side of dishwasher to gain access to drain hose and drain check valve; us
... Read more
ed pliers to remove hose clamp; placed flat pan underneath to catch remaining water drainage; unscrewed drain check valve; tested under bathroom faucet--determined faulty; replaced with the new one, restored connections, reset dishwasher in proper location; voila--fixed! Plan to return the unneeded impeller kit.
Read less
This water inlet valve regulates the flow of water into the appliance as needed during operation. It is commonly replaced when water fails to enter, flow becomes inconsistent, or leaks develop.
This water inlet valve regulates the flow of water into the appliance as needed during operation. It is commonly replaced when water fails to enter, flow becomes inconsistent, or leaks develop.