My Orders
KitchenAid Dishwasher Fuses
GET YOUR OFFICIAL KitchenAid PARTS TO ENSURE VICTORY
Popular KitchenAid Dishwasher Fuses
This part is used as a safety device to protect the dishwasher circuit from overload. If the temperature gets to high it will shut off the electrical current to the heating unit in the appliance. Also known as Thermal Fuse.
This part is used as a safety device to protect the dishwasher circuit from overload. If the temperature gets to high it will shut off the electrical current to the heating unit in the appliance. Also known as Thermal Fuse.
Installation Instructions
Douglas from Dallas, GA
would not turn on
I did a search on the website and read the instructions for trouble shooting. I took the inside door off by taking the screws out. I pulled the part and tested it and found it did not in fact have no ampage. I then ordered the part on line. It came in two days, I plugged it in, put the door back together and the total time was about 15-
... Read more
20 minutes. Easy, simple, great instructions and the entire thing only costed me the part itself. It's working great now! And I've never worked on appliances before.
Read less
This is a replacement thermal fuse for your dishwasher. The thermal fuse is sometimes known as the thermal cutoff. The thermal fuse shuts off the dishwasher if the dishwasher shorts out or overheats. If your dishwasher is cutting out during the cycle, or will not start, you may have an issue with your thermal fuse. If your dishwasher control panel does not light up, the first thing you should check is the fuse. Before you begin to repair this part, be sure to disconnect the dishwasher from the power source, as you will be working around electricity.
This is a replacement thermal fuse for your dishwasher. The thermal fuse is sometimes known as the thermal cutoff. The thermal fuse shuts off the dishwasher if the dishwasher shorts out or overheats. If your dishwasher is cutting out during the cycle, or will not start, you may have an issue with your thermal fuse. If your dishwasher control panel does not light up, the first thing you should check is the fuse. Before you begin to repair this part, be sure to disconnect the dishwasher from the power source, as you will be working around electricity.
Installation Instructions
Robert from BOULDER, CO
Faulty door handle shorted out the fuse.
First electrical power to the dish washer was turned off. The top portion of front door panel was then opened up to expose pocket handle and latch assembly. Old latch assembly was replaced with new latch assembly and a new fuse. The door panel was then re-closed and electrical power turned on.
*Please Note - When changing the fuse always use a new wiring harness.
*Please Note - When changing the fuse always use a new wiring harness.
Installation Instructions
Jeff from Boaz, KY
Touch pad on dishwasher dead
1. Remove the two screws that attach the bottom cover.
2. Remove the 2 screws that attach the door outer cover.
3. Remove the 8 screws that attache the door inner cover.
4. Remove the plastic cover over the electronic controller.
5. Remove the two connections to the thermal fuse.
6. Remove the thermal fuse.
... Read more >7. Install the new thermal fuse.
Reverse the above steps.
2. Remove the 2 screws that attach the door outer cover.
3. Remove the 8 screws that attache the door inner cover.
4. Remove the plastic cover over the electronic controller.
5. Remove the two connections to the thermal fuse.
6. Remove the thermal fuse.
... Read more >7. Install the new thermal fuse.
Reverse the above steps.
Read less
When replacing these fuses the wire harness must be replaced as well. It is located in the control panel. The harness is included with this part now.
When replacing these fuses the wire harness must be replaced as well. It is located in the control panel. The harness is included with this part now.
Installation Instructions
tony from carrollton, TX
Controller board replacement
Simple task - remove the front door cover to expose the cover for the control panel which is then also removed. Be sure electricity is disconnected from the appliance, then simply remove the old control board (remove the quick-connect wire harness) and slide the replacement board back in. Reconnect wiring harness, replace cover and door p
... Read more
anel, then turn-on electricy. NOTE - I suggest you shut off power at the breaker panel vs. disconnected the direct wiring at the appliance. The reason for this is because the new controller board could be damaged in the process of connecting the wires and any sparking that would take place when working with hot wiring.
Read less
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY