My Orders
Kenmore Washer Motors
GET YOUR OFFICIAL Kenmore PARTS TO ENSURE VICTORY
Popular Kenmore Washer Motors
This direct drive motor coupling (Direct Drive Washer Motor Coupling, Motor Coupling, Washer Motor Coupling, Coupling Kit) provides a cushioned connection between the transmission and the motor shaft. It attaches to the direct-drive transmission and the motor shaft. If this part is defective it will affect the agitator in your washer because of its direct connection with the motor. Your washer may not agitate, spin slowly, or not spin at all. The coupling must be replaced when there is no longer a consistent connection between the transmission and the motor shaft. The coupling can wear over time because of its location between two major parts of the dryer. It is subject to material fatigue over time from normal use, or breakage caused by frequent overloading. The part measures approximately 2 inches in diameter, and is constructed of plastic and metal. This model comes in black/white.
This direct drive motor coupling (Direct Drive Washer Motor Coupling, Motor Coupling, Washer Motor Coupling, Coupling Kit) provides a cushioned connection between the transmission and the motor shaft. It attaches to the direct-drive transmission and the motor shaft. If this part is defective it will affect the agitator in your washer because of its direct connection with the motor. Your washer may not agitate, spin slowly, or not spin at all. The coupling must be replaced when there is no longer a consistent connection between the transmission and the motor shaft. The coupling can wear over time because of its location between two major parts of the dryer. It is subject to material fatigue over time from normal use, or breakage caused by frequent overloading. The part measures approximately 2 inches in diameter, and is constructed of plastic and metal. This model comes in black/white.
Installation Instructions
Jeff from Wayne, NJ
No movement from Basket & agitator
The job looked intimidating but turned out to be very easy.
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pum ... Read more p.
The motor comes off next. Unplug the electrical connector from the motor and two wires from the capacitor. Remove the two screws holding the clamps in place and then pop off the two clamps. You will need to hold up the motor with one hand while you remove the clamps or it will fall to the floor once the clamps are removed.
One piece of the coupling assemble will be attached to the motor and the other will be attached to the gearcase drive shaft. If you want to clean up the mess created by the shredded rubber center piece of the coupling assembly you will have to take off the motor mounting plate. It is held on by two bolts and removing it makes installing the coupling easier but probably not necessary.
Push the back half of the coupling on to the gearcase drive shaft until the shaft is flush with the face of the coupling. Install the new rubber center piece on to the coupling then re-install the motor mounting plate. Install the other half of the coupling on to the motor shaft and lift the motor up to the coupling. You have to rotate the motor shaft by spinning the fan blades until the coupling lines up so you can slide it into the other half of the coupling. Then just reattach the motor, connectors and water pump in the reverse order of disassembly.
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pum ... Read more p.
The motor comes off next. Unplug the electrical connector from the motor and two wires from the capacitor. Remove the two screws holding the clamps in place and then pop off the two clamps. You will need to hold up the motor with one hand while you remove the clamps or it will fall to the floor once the clamps are removed.
One piece of the coupling assemble will be attached to the motor and the other will be attached to the gearcase drive shaft. If you want to clean up the mess created by the shredded rubber center piece of the coupling assembly you will have to take off the motor mounting plate. It is held on by two bolts and removing it makes installing the coupling easier but probably not necessary.
Push the back half of the coupling on to the gearcase drive shaft until the shaft is flush with the face of the coupling. Install the new rubber center piece on to the coupling then re-install the motor mounting plate. Install the other half of the coupling on to the motor shaft and lift the motor up to the coupling. You have to rotate the motor shaft by spinning the fan blades until the coupling lines up so you can slide it into the other half of the coupling. Then just reattach the motor, connectors and water pump in the reverse order of disassembly.
Read less
This is a 2-speed drive motor for your washing machine. The motor rotates the spin basket when the washing machine is in spin or tumbling mode. You will likely need to replace the motor if you are experiencing burning smells or your washer will not start. The tools you will need to make this repair include a number two Phillips screwdriver, a flat-blade screwdriver, and a 5/16 nut driver.
This is a 2-speed drive motor for your washing machine. The motor rotates the spin basket when the washing machine is in spin or tumbling mode. You will likely need to replace the motor if you are experiencing burning smells or your washer will not start. The tools you will need to make this repair include a number two Phillips screwdriver, a flat-blade screwdriver, and a 5/16 nut driver.
Installation Instructions
Lowell from Dover, DE
Washer had water leak in lower front and would not drain.
Laid the washer on its back and found leak in water pump. Found out it was caused by vibration from motor with bad bearing. Removed pump and motor which were held on by clips. Both were removed and replaced without removing cabinet from machine.
This motor rotor connects to the spin basket shaft and rotates the spin basket in washers. Unplug the washer before installing, and wear work gloves for safety. Verify compatibility with your model before purchasing.
This motor rotor connects to the spin basket shaft and rotates the spin basket in washers. Unplug the washer before installing, and wear work gloves for safety. Verify compatibility with your model before purchasing.
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
This washer rotor is a genuine replacement component designed to drive the spin basket in select washing machines. It functions by generating a magnetic field that interacts with the stator, producing the torque required to rotate the drum at various speeds during wash and spin cycles. The rotor plays a critical role in ensuring smooth, stable operation, reducing noise and vibration while enhancing energy efficiency. Common symptoms indicating the need for replacement include a washer that won’t spin, leaves clothes excessively wet, or produces unusual motor sounds. Compatible with a range of Whirlpool-family brand models, installation should be performed with the appliance unplugged and may require basic tools and reference to model-specific instructions.
This washer rotor is a genuine replacement component designed to drive the spin basket in select washing machines. It functions by generating a magnetic field that interacts with the stator, producing the torque required to rotate the drum at various speeds during wash and spin cycles. The rotor plays a critical role in ensuring smooth, stable operation, reducing noise and vibration while enhancing energy efficiency. Common symptoms indicating the need for replacement include a washer that won’t spin, leaves clothes excessively wet, or produces unusual motor sounds. Compatible with a range of Whirlpool-family brand models, installation should be performed with the appliance unplugged and may require basic tools and reference to model-specific instructions.
The drive motor spins the spin basket and drives the agitator or spin basket in the agitation or tumbling mode.
The drive motor spins the spin basket and drives the agitator or spin basket in the agitation or tumbling mode.
This motor stator assembly is a key component in top-load washing machines, responsible for generating the magnetic field that interacts with the rotor to spin the wash basket. Its precise operation ensures effective agitation and spinning during wash cycles, contributing to thorough cleaning and balanced load handling. A faulty stator can result in symptoms such as the washer not starting, failing to agitate or spin, or producing unusual noises. This genuine OEM part is designed for compatibility with select models and meets manufacturer standards for performance and reliability. Installation typically involves accessing the motor housing, removing the rotor, and securing the stator in place with proper alignment and electrical connections.
This motor stator assembly is a key component in top-load washing machines, responsible for generating the magnetic field that interacts with the rotor to spin the wash basket. Its precise operation ensures effective agitation and spinning during wash cycles, contributing to thorough cleaning and balanced load handling. A faulty stator can result in symptoms such as the washer not starting, failing to agitate or spin, or producing unusual noises. This genuine OEM part is designed for compatibility with select models and meets manufacturer standards for performance and reliability. Installation typically involves accessing the motor housing, removing the rotor, and securing the stator in place with proper alignment and electrical connections.
This rotor assembly is a manufacturer-approved replacement part for your washing machine. The rotor is an important part to rotate the tub during the wash cycle. It can need replacing if the magnets or splines become damaged. Unplug the washer before beginning this repair. To complete this repair, you will need a Phillips screwdriver, a 17mm socket wrench, and thread-locking fluid.
This rotor assembly is a manufacturer-approved replacement part for your washing machine. The rotor is an important part to rotate the tub during the wash cycle. It can need replacing if the magnets or splines become damaged. Unplug the washer before beginning this repair. To complete this repair, you will need a Phillips screwdriver, a 17mm socket wrench, and thread-locking fluid.