Kenmore Washer Sensors
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Kenmore Washer Sensors
Your Price
$55.29
In Stock
Kenmore Washer Sensor Assembly
PartSelect Number PS16556422
Manufacturer Part Number 6501KW2002B
This is a replacement sensor assembly for your washer. It may also be known as a motor rotor position sensor. The sensor assembly monitors the direction and speed of the spinning rotor and communicates this information to the electronic control board. If your washer pumps but will not spin or agitate, you may have a damaged sensor assembly. This part is sold individually, and is an OEM part sourced directly from the manufacturer. Be sure to shut off the power to your washer before you begin this repair.
Fixes these symptoms
- Spinning Issues
- Spins slowly
- Will not agitate
- See more...
Installation Instructions
Mark from Harrisburg, PA
LE Error Message and won't spin drum properly
I first tested the motor per the service manual. I checked the resistance between the terminals of the 3 pin connector. It's supposed to be 5-15 ohms. The motor checked out so I replaced the main electrical board. It turns out that wasn't the problem. After a brief web search I found out that the hall sensor (which is attached to the motor stator) was the likely cause of the failure. I replaced that and everything works great now. And now I have a spare main board in case that ever fails. I also want to mention that I took the time to remove the dispenser box (where the water comes in and is directed to the different cleaning products) and cleaned it with a very strong bleach solution. It got rid of the mildew and funky smell. It seems that the fabric softener caused a lot of mildew to form inside the dispenser directly above the fabric softener tray. The bleach took care of that. This is probably something that should be done routinely to keep the mildew from forming.
Read more...
Your Price
$38.96
In Stock
Kenmore Washer Sensor
https://www.youtube.com/watch?v=_-Hg8rLGiKQ
The hardest part on fixing this is trying to move the washer out of its place so I can tilt it to see underneath the washer where the repair would be. Read more...
PartSelect Number PS11749664
Manufacturer Part Number WPW10178988
This rotary position sensor is a genuine OEM part for your washing machine. It helps to ensure the load of clothing stays balanced during the wash cycle. Customers have rated this repair as easy. To complete this repair, you will need an Allen wrench, 3/8 inch socket, and a screwdriver. The repair will involved turning off the power and water supply, and tilting the washer on its front to access the sensor.
Fixes these symptoms
- Spinning Issues
- Will not agitate
- Will Not Start
- See more...
Installation Instructions
Edgardo from SALEM, OR
F51 error code
Pretty easy! Just follow this link on how to fix the problem: https://www.youtube.com/watch?v=_-Hg8rLGiKQ
The hardest part on fixing this is trying to move the washer out of its place so I can tilt it to see underneath the washer where the repair would be. Read more...
Your Price
$77.99
In Stock
Kenmore Washer Water Inlet Flowmeter
PartSelect Number PS11748313
Manufacturer Part Number WPW10110225
This part continually measures the amount of water entering the tub. It will make adjustments if too much or too little water is present.
Fixes these symptoms
- Leaking
- No hot or cold water
- Water Filling Issues
- See more...
Installation Instructions
Jerry from Keenes, IL
washing machine giving f20 error code
removed washer top, checked supply hoses and inlet valve to make sure not clogged, replaced valve and while already there replaced flowmeter, reinstall top and hoses and checked machine operation, machine working fine and wife thinks i am her hero
Read more...
Your Price
$24.67
In Stock
Kenmore Washer Thermistor
PartSelect Number PS3528953
Manufacturer Part Number 6322FR2046C
Discover the essential LG thermistor, a key component for your washing machine performance. Expertly designed and produced by LG Electronics, this part functions in unison with the main control board to accurately monitor the water temperature. Ensure safe installation by unplugging your washer in advance and wearing protective gloves. With flawless precision and performance, this thermistor guarantees smooth functioning of your device, making it an ideal choice for maintaining your LG washer. Always remember to refer to your model's manual to confirm compatibility. Trust in the superior quality promised by LG for a carefree laundry experience.
Fixes these symptoms
- Will Not Start
- See more...
Your Price
$34.74
In Stock
Kenmore Washer Temperature Sensor
be careful when disconnecting the two prong electrical connector from
the heat sensor. the two black wires can pull free easily. In that case, the
rear of the female plastic wired connector must be extracted to allow the two black wires to be "pushed" into the narrow slot which displaces the
wire insulation and allows for a good electrical connection. If a punch tool is not available a pair of needle nose pliers works. Also, observe
the orientation slots on both the male andfemale connectors - they
connect one way only! I set the washer on it's face while effecting this
repair to better see what I was doing (eyesight not as good as it used to be). Thanks for the timely support! Read more...
PartSelect Number PS11755214
Manufacturer Part Number WPW10467289
This part regulates the temperature of the water in the tub. The sensor is located in the heating element.
Fixes these symptoms
- No hot or cold water
- Will not drain
- Will Not Start
- See more...
Installation Instructions
william from VIRGINIA BCH, VA
Replacing the heat sensor following an F-24 Error Notice.
I followed your repair video explicitly, simple fix. However, one shouldbe careful when disconnecting the two prong electrical connector from
the heat sensor. the two black wires can pull free easily. In that case, the
rear of the female plastic wired connector must be extracted to allow the two black wires to be "pushed" into the narrow slot which displaces the
wire insulation and allows for a good electrical connection. If a punch tool is not available a pair of needle nose pliers works. Also, observe
the orientation slots on both the male andfemale connectors - they
connect one way only! I set the washer on it's face while effecting this
repair to better see what I was doing (eyesight not as good as it used to be). Thanks for the timely support! Read more...
Your Price
$64.69
In Stock
Kenmore Washer Sensor
PartSelect Number PS11751018
Manufacturer Part Number WPW10247389
Introducing the genuine OEM Sensor from Whirlpool, designed for optimal performance in select models of Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef appliances. This sensor is specifically crafted to monitor coins inserted into the coin box of commercial laundry machines, ensuring accurate operation. Do remember that while parts may share similar appearance, variations in size and shape can occur. Therefore, ensure you have the correct part number for your specific appliance model before order placement. Prior to installation, ensure to unplug the appliance and wear work gloves for enhanced safety. Trust Whirlpool for components that are both functional and durable.
Your Price
$49.50
Special Order
Your Price
$82.95
In Stock
Kenmore Washer Water-level Pressure Switch
PartSelect Number PS4217080
Manufacturer Part Number DC96-01703B
The pressure switch senses and controls the water level in the washer.
Installation Instructions
Fredric from ROCKMART, GA
The water level was lower than normal.
First unplug or turn off thee circuit breaker. Then remove the two screws to the top cover. Slide the cover back about three inches then remove the cover. Next take out the screw to the old sensor. Then unplug the electrical connection by squeezing and the pulling to disengage. Now set the old unit aside. You then grad your eight inch wire tie and hold the with flat side to the right and just to the right of the screw hole for the bracket is a square hole. Feed to wire tie into the square hole with your left hand then loop down left side of the end of new sensor and back up threw the square hole and tighten with the pliers. Your new sensor will be positioned just like it was mounted to the metal bracket. And pretty ridged. Now connect the vacuum hose and electrical connector.
Read more...
Your Price
$49.52
In Stock
Kenmore Washer Thermistor
PartSelect Number PS4204988
Manufacturer Part Number DC32-00010C
This thermistor is for washers.
Thermistor monitors and helps regulator the water temperature in the washer.
Unplug the washer before installing this part. Wear work gloves to protect your hands.
Your Price
$77.22
Special Order
Related Kenmore Washer Parts
- All Kenmore Washer parts
- Kenmore Washer Agitators
- Kenmore Washer Bearings
- Kenmore Washer Belts
- Kenmore Washer Brackets and Flanges
- Kenmore Washer Caps and Lids
- Kenmore Washer Circuit Boards and Touch Pads
- Kenmore Washer Dispensers
- Kenmore Washer Doors
- Kenmore Washer Drawers and Glides
- Kenmore Washer Drums and Tubs
- Kenmore Washer Ducts and Vents
- Kenmore Washer Electronics
- Kenmore Washer Elements and Burners
- Kenmore Washer Filters
- Kenmore Washer Handles
- Kenmore Washer Hardware
- Kenmore Washer Hinges
- Kenmore Washer Hoses and Tubes
- Kenmore Washer Knobs
- Kenmore Washer Latches
- Kenmore Washer Legs and Feet
- Kenmore Washer Lights and Bulbs
- Kenmore Washer Manuals and Literatures
- Kenmore Washer Motors
- Kenmore Washer Panels
- Kenmore Washer Power Cords
- Kenmore Washer Pumps
- Kenmore Washer Seals and Gaskets
- Kenmore Washer Springs and Shock Absorbers
- Kenmore Washer Switches
- Kenmore Washer Timers
- Kenmore Washer Transmissions and Clutches
- Kenmore Washer Valves
- Kenmore Washer Wheels and Rollers
- Kenmore Washer Wire Plugs and Connectors