Kenmore Washer Wire Plugs and Connectors

Videos!

Your Price

$19.30

Kenmore Washer Drive Block - 2 5/16 Inch High

★★★★★

2 Reviews

PartSelect Number PS11741977

Manufacturer Part Number WP389140

This washer drive block is an essential component that connects the inner spin basket to the drive shaft, enabling proper spinning during wash and spin cycles. Measuring approximately 2-5/16 inches high, it is designed for large-capacity washers with belt or direct drive systems. A worn drive block can cause loud noises, shaking, poor spinning, or leave clothes excessively wet. Installation requires basic tools and disassembly; always unplug the appliance and shut off water supply before starting the repair. Regular inspection and timely replacement help maintain optimal washer performance.

Fixes these symptoms

Leaking
Spins slowly
Will not agitate
See more...

Installation Instructions

Dexter from Milwaukie, OR

Washer made a loud banging noise at end of spin cycle, leaked water and agitator seemed loose

After entering the model number of your appliance you will be taken to a page where all of the parts are displayed by sections. On that page about in the middle there is a heading called "Find Part By Symptom." I figured out from there which symptom the washer had and read what other people were saying and how they made the repairs. Basically I had three problem areas, Noise, Leaking and a problem with the agitator. I focused on the loud noise first and decided I needed to replace the clutch/brake assemblies. I found the clutch parts page and on that page there was a video on how to make this repair. This video is all you need to gain access to all moving parts located under the cabinet. Which ever part you are replacing, I recommend watching this video! After removing the console, back panel and cabinet then laying the machine on its back just as seen on the video, I had access to the water pump, motor, transmission and related clutch/brake parts. As it turned out I did not need the clutch/brake assembly but as a precaution and because the parts were cheap, I replaced the motor coupling, water pump and tub wear pads. I decided to replace the agitator assembly because of several worn parts associated with the dog ears/drive shaft ETC. I put the machine back upright and took off the top cap on the agitator, then there is an inner cap with seal that gives access to the 7/16" bolt you must remove to remove the agitator. However once the agitator was removed I noticed metal shavings and play in the shaft. I used a spanner wrench to remove the spanner nut. I removed the Plastic Tub Ring (has several clips around the outer tub), then removed the inner washer tub to replace the Drive Block. Replacing the Drive Block stopped the loud noise at the end of the spin cycle. Now just reverse the order to put the machine back together and your done. For my situation it was best to take the machine apart and decide which parts I needed before ordering to minimize errors. These machines are made very cheaply and are designed to brake at some point in time and it is very easy to determine which parts are worn because most are made of plastic. In this process I also noticed where my leaks (did I say Leaks) were coming from. There were two hose clamps installed improperly from the factory, so check all clamps, hoses ETC. and you should be good to go. Read more...

Your Price

$58.42

Kenmore Washer Terminal And Wire Kit

PartSelect Number PS334181

Manufacturer Part Number 279318

This dryer terminal and wire kit is designed to replace damaged or worn wiring that connects to the terminal block, helping restore proper electrical function and heat performance. The kit includes replacement wires, wire nuts, and screws, but does not include the terminal block itself. It is commonly used to resolve issues such as a dryer not heating or producing insufficient heat caused by loose or faulty connections. Installation requires securing the new wires to the terminal block and tightening connections for safe operation.

Your Price

$81.63

Kenmore Washer Wire Harness

PartSelect Number PS12348902

Manufacturer Part Number W11193817

This wire harness is a genuine OEM component designed for Whirlpool washing machines, ensuring reliable electrical connectivity between critical parts. It serves as a bundled network of wires that transmits power and signals to synchronize the washer’s control panel, motors, sensors, and water inlet valve. By coordinating these components, the harness enables smooth operation of the washing cycle. Installation involves disconnecting the appliance from power, accessing the internal wiring, and replacing the harness with care to maintain proper connections. A faulty harness can lead to issues such as malfunctioning lights, failure to start, or irregular cycle performance, making this part an essential solution for restoring optimal functionality.

Your Price

$36.85

Kenmore Washer Motor Harness

PartSelect Number PS3530254

Manufacturer Part Number 6877ER3003B

Your Price

$23.60

Kenmore Washer Harns-wire

PartSelect Number PS16218050

Manufacturer Part Number W11458657

Your Price

$64.69

Kenmore Washer Wire Harness

PartSelect Number PS16660539

Manufacturer Part Number W11568984

Experience the reliable and high-quality performance of this genuine Whirlpool product. The HARNS-WIRE Harness, lower is specifically designed for some models of Whirlpool and its sub-brands. This lower wire harness is a key component that connects the electrical components of your washer to its power source. Please make sure to unplug your washer before installing this integral part. To safeguard your hands, it's advisable to wear work gloves during the installation process. Trust this integral Whirlpool HARNS-WIRE Harness, lower to keep your washer functioning optimally.

Your Price

$29.47

Kenmore Washer Connector Assembly

★★★★★

3 Reviews

PartSelect Number PS7786632

Manufacturer Part Number ACJ73350401

Installation Instructions

Richard from RED LION, PA

Water leaking into drum

Figured out how to remove the top door and the top panel that covered the solenoid bank. That was the hardest part. Swapping out the solenoid bank and the connector was easy. No more water leaking. Read more...

Your Price

$68.86

Kenmore Washer Wire Harness

PartSelect Number PS16730801

Manufacturer Part Number W11591637

This wire harness provides essential electrical connections between components, ensuring stable signal and power flow. Replacement is recommended when wear, damage, or loose connections affect appliance performance.