Official Electrolux Range Parts | Order Today, Ships Today

Your Price

$36.00

In Stock

Oven Probe

★★★★★

(33)

PartSelect Number PS1528542

Manufacturer Part Number 316490000

This genuine OEM oven probe is also known as an oven temperature sensor or range probe. This part is manufactured for a range, stove, or oven to detect the temperature within the oven cavity. The probe allows the oven to maintain the set temperature by sensing the temperature and sending the information to the ovens motherboard. You may need to replace this part if oven is not heating or is heating unevenly. Be sure to disconnect power to oven before replacing, as it is an electrical part. Tools needed are 1/4 inch nut driver and needle nose pliers.

Fixes these symptoms

Element will not heat
Little to no heat when baking
Oven is too hot
See more...

Installation Instructions

Tim from ASHAWAY, RI

oven did not heat up

Replaced the probe because that's what this site recommended.The oven still does not heat up. Read more...

Temperature Sensor – Part Number: 316217002

Your Price

$39.92

In Stock

Temperature Sensor

★★★★★

(11)

PartSelect Number PS820208

Manufacturer Part Number 316217002

The oven temperature sensor for your range may also be called a probe. The quick connect on this part may differ than your original piece. If the temperature sensor does not fit you will have to cut off the quick connect, and then wire together with porcelain wire nuts. The function of the oven temperature sensor is to measure the temperature in the oven and signal the other heating components. Before you begin this repair make sure to disconnect the power to the range. The tools required for this installation include a number two Phillips screwdriver or a number two square head screwdriver, and maybe a pair of wire strippers and crimpers.

Fixes these symptoms

Element will not heat
Little to no heat when baking
Oven is too hot
See more...

Installation Instructions

Dan from Bellevue, ID

Oven not heating to desired temperature

Replaced clock control by removing surface burner control knobs and plastic nuts, and then the cover over the oven control. Two screw hold the clock in place, after removal and disconnecting the plug-in you can reinstall the new clock control. The Heat Sensor inside the oven will also need to be replaced. It is located inside the oven and attached with two screws; the back of the oven will need to be removed to unplug. Reverse removal procedure and turn the power back on to the stove. Read more...

Your Price

$18.78

In Stock

Anti-Tip Kit

★★★★★

(4)

PartSelect Number PS3655242

Manufacturer Part Number 316112005

The anti-tip bracket kit comes with one metal bracket and two installation screws, and is sourced directly from the genuine manufacturer. It prevents the freestanding oven, range, or stove from tipping when force or weight is applied to an open oven door. The bracket is secured to the floor and wall and fits over the rear leveling leg in the back of the appliance, in a cutout specifically designed for the anti-tip bracket. This part is very essential to the safe operation of the appliance. Failure to install the bracket properly can result in the oven tipping or falling and causing injuries.

Installation Instructions

Brian from Panama City Beach, FL

anti-tip bracket not installed

I was selling my home and did not realize that the anti-tip bracket was not originally installed. A home inspection caught the problem and the buyers required that I install one. I could not find the original and obviously the installer never put it in place to begin with. The buyers wanted this resolved within a week so I had to act fast. I could not find one locally so I found what I needed on your website. It arrived in a couple of days and was easy to install. I used the template provided in the kit and drove the screws through the bracket into the wood plate behind the drywall. Pushed the range back in place and that's it. Couldn't get any easier. Read more...

Temperature Sensor – Part Number: 5304504897

Your Price

$27.35

In Stock

Temperature Sensor

★★★★★

(4)

PartSelect Number PS11758156

Manufacturer Part Number 5304504897

Fixes these symptoms

Element will not heat
Little to no heat when baking
Oven is too hot
See more...

Installation Instructions

Alexander from DELMAR, NY

Both oven bake and broil elements lost power suddenly at the same time.

Installation of the temparature sensor, one of the technician recommended parts took no time, just two screws and a snap off/snap on part. It did not fix the problem. I then replaced the main control panel, which requires more work, but didn't solce the ussue either. I then replaced the thermal fuse, which wasn't mentioned by tech support, and required much more disassebly of the top panels of the stove, with still no fix to the problem. I am waiting to replace the thermostat heat sensor unit, the only other part in the circuit controlling power supply, requiring removal of the stove top again, Read more...

Oven Bake Igniter – Part Number: 316489403

Your Price

$107.15

In Stock

Oven Bake Igniter

★★★★★

(14)

PartSelect Number PS2364063

Manufacturer Part Number 316489403

The oven burner igniter simply ignites the gas so it can heat the oven burner. The igniter does this by drawing electrical currents through the oven safety valve to open it. If the element shortens out, is no longer glowing, or is only glowing red or orange, replacing the igniter is the solution. You will need a wire splicing tool to do this repair. First, disconnect the wire harness from the igniter by removing the access panel on the rear of the stove. Next, access the front of oven and take out the racks before removing the bottom of the oven. For the rest of the installation instructions refer to the diagram provided by the manufacturer. Remember to unplug your oven from the power source before beginning this project.

Fixes these symptoms

Element will not heat
Gas igniter glows, but will not light
Gas smell
See more...

Installation Instructions

Sparky from ACCOMAC, VA

Stovetop worked, oven did not.

First, remove the warming drawer. This allows access to the igniter's plug. Unplug the igniter. The rest of the job is performed within the oven. Remove the bottom (1/4 inch socket). Then remove the next, v shaped piece. The igniter is bolted to the aerator. Remove bolts, and it pulls right off. Reverse these to install new igniter. Read more...

Oven Light Bulb – Part Number: 316538904

Your Price

$12.13

In Stock

Oven Light Bulb

★★★★★

(7)

PartSelect Number PS12751166

Manufacturer Part Number 316538904

Clear, 120 Volt, 40 Watt.

Installation Instructions

Colin from Hollis, NY

Ice-Maker and Water Dispenser not working.

First I disconnected the power cord, then removed the screws that held the bracket that holds the base for the water-filer in place. I then disconnected the water lines(intake and outflow). Next I removed the screws that held the water-filter's base in place. I then disconnected the release lock mechanism for the filter and finally removed the water-filter base. I did the reverse to install the new water-filter base. Previously I had tested the intake water line and noticed the water was flowing with enough pressure upto the water-filter's base but no water was exiting thru the outflow line, which leads to the Ice-Maker and Dispenser. I had tried changing the filter but that didn't solve the problem it was then I had realized that the Base was the problem. The actual problem was the spring-loaded valves for both the intake and outflow lines, which had a plastic prong that protrudes out of the base that is triggered by the filter when installed. The two prongs were worn-down so the filter wasn't activating the spring-loaded release valve to let the water thru. As for the light, I just unscrewed it. Read more...

Main Terminal Block Kit – Part Number: 5304409888

Your Price

$6.72

In Stock

Main Terminal Block Kit

★★★★★

(10)

PartSelect Number PS471605

Manufacturer Part Number 5304409888

Terminal block kits are also known as terminal boards, or terminal strips, and they are found in a wide variety of household appliances. Most often in ranges, wall ovens, and dryers. This kit attaches the power cord to the inner wiring of your appliance. If the terminal block is faulty, your appliance will not get the power it needs to operate properly. When removing the old block pay close attention to the wire placement, this will make installing your new part much easier. If you notice any of the wires or wire terminals are corroded or damaged they will also need to be replaced.

Fixes these symptoms

Element will not heat
Little to no heat when baking
Little to no heat when broiling
See more...

Installation Instructions

Timothy from Spring Valley, AL

Cord was not tightened enough by delivery crew.

PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful. Read more...

Left Front Orifice - 9.5K – Part Number: 316527500

Your Price

$15.67

In Stock

Left Front Orifice - 9.5K

★★★★★

(2)

PartSelect Number PS2332664

Manufacturer Part Number 316527500

LEVELING LEG ASSY – Part Number: 5304509869

Your Price

$4.06

On Order

LEVELING LEG ASSY

★★★★★

(3)

PartSelect Number PS12364627

Manufacturer Part Number 5304509869

Sold Individually. These legs should be adjusted to make your appliance level on uneven flooring.

Installation Instructions

Melinda from Three Rivers, MA

Rusted leveling foot

I couldn't unscrew the leveling foot because it was rusted and corroded. The bracket holding it was easy to remove so I took the bracket with the corroded foot off and replaced it with the new foot and bracket. Very simple. I made sure I oiled it so it wouldn't rust again. Read more...

Your Price

$7.84

In Stock

Steel Washer

PartSelect Number PS436497

Manufacturer Part Number 316008401

This steel washer is also known as the range washer and is used on your oven door. The measurements for the steel washer are a three quarter inch outer diameter, and a one quarter inch inner diameter. This washer is an OEM part, made of steel, which is sourced directly from the manufacturer. This specific steel washer is used with your range, to secure the inner and outer door together and to secure the oven door handle back in place. Users have ranked this repair as a simple installation that should take you less than fifteen minutes to complete.

Installation Instructions

KELLY from LAKELAND, FL

Handle on oven door broke

called around and way to much money for repair man as well as parts from local appliance repair store. They wanted 10.00 for a screw that we got from you for $3.00 same as all the other parts saved over 70.00 dollars.

quick delivery and easy repair ... like new again .

would use you again Read more...

Electrolux Range Parts

Popular Electrolux Range Parts

Appliance Type

Related Parts

Popular Electrolux Range Models

Electrolux Range Parts

Find your part

Popular Electrolux Range Parts

Appliance Type

Related Parts

Popular Electrolux Range Models