Electrolux Range Elements and Burners
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Electrolux Range Elements and Burners
Your Price
$37.91
In Stock
Electrolux Range Surface Element - 8 Inch 2600w
PartSelect Number PS2339242
Manufacturer Part Number 316442301
The range surface element provides heat to the cooking surface on top of the range. The element has a universal plug, is 8 inches in diameter, spans 5 coils in width and reaches 2600 watts. Before you begin your repair, ensure that the elements are turned off and have had time to cool. Once you have removed the element this is a good time to ensure the terminal is in good condition (they can wear over time) which may need to be replaced as well. This quick repair requires no tools except gloves for safety, and a small amount of time.
Fixes these symptoms
- Element will not heat
- Will Not Start
- See more...
Installation Instructions
David from Encinitas, CA
burner shorted out
I followed the directions by clipping wires to old burner socket, splicing the wires to new terminal block, screwing down new "block bracket," and plugging in new burner.
Read more...
Your Price
$72.00
In Stock
Electrolux Range Element
Labeled the wire sets connected to the front control panel.
Gently lifted up the stove top and flipped it over on to a towel.
Removed the piece of metal holding down the burner.
Disconnected the cables to the old burner.
Repeated steps above in reverse. Read more...
PartSelect Number PS16763418
Manufacturer Part Number 5304533520
Dual Radiant Surface Element
Fixes these symptoms
- Element will not heat
- Will Not Start
- See more...
Installation Instructions
German from SELLERSBURG, IN
Center of dual burner was broken
Removed screws on the sides and front.Labeled the wire sets connected to the front control panel.
Gently lifted up the stove top and flipped it over on to a towel.
Removed the piece of metal holding down the burner.
Disconnected the cables to the old burner.
Repeated steps above in reverse. Read more...
Your Price
$28.41
In Stock
Electrolux Range 6-inch Coil Burner Element
PartSelect Number PS2368974
Manufacturer Part Number 318372211
This element is a genuine OEM replacement part, has looped terminal ends, comes with a black medallion center, and fits most electric ranges. All burners are made of a heating wire that produces heat from electricity. Remove the non-functional burner element from the terminal block (or receptacle). Use a multi-meter to check for continuity. Check the end of the terminals for corrosion or heat damage. If there is corrosion or heat damage, replace the whole terminal block or receptacle at the same time you replace the damaged coil. Before you start this repair, make sure that the element is turned off and cool to the touch.
Fixes these symptoms
- Element will not heat
- Will Not Start
- See more...
Installation Instructions
Matthew from Columbus, IN
Burners on 53 year old range kept going out
When we bought our home less than a year ago, we had three functional burners on our 40" wide 50's classic Kelvinator (not close to standard size these-a-days). After a few months of use, two more burners went out for good and we were stuck using the back left burner for all of our cooking. I opted for the premium burners and made sure to compare my terminals with the ones online to be sure they mounted the same. I removed the burners and terminals, clipped the wires going into the terminals, and removed the top of the stove. I followed the directions that came with the new terminals, pushed in the new burners and viola! All four burners now work. I gave the stove a general cleaning and now my 1954 Kelvinator looks and cooks like it is brand new. It was easily the best $109 I've spent on my home.
Read more...
Your Price
$114.40
In Stock
Electrolux Range Radiant Element With Limiter - 1200w
PartSelect Number PS1528719
Manufacturer Part Number 318178110
This is a six-inch radiant element with limiter. It works in conjunction with your stove top range. The purpose of this part is to heat up the cooking area that is located on top of the range, also known as your stove top. If you suspect that your surface element is not properly heating then you may want to test the element for continuity. This model is sold individually and is 1200 watts. The tools you will need for this installation include a Phillips screwdriver and a 14-inch nut driver.
Fixes these symptoms
- Element will not heat
- Will Not Start
- See more...
Installation Instructions
Lori from Winter Haven, FL
burned out burner
First we removed two screws under the rim of the range top to open the lid. Lifted the lid and removed the screws from the bracket that holds the elements, Be careful with the clips that hold the element in, if you break them or bend them there aren't any more! Also note which holes they were in, they are marked according to the different sizes of elements. Disconnected the wires, needed needlenose pliers to grip them...connected new element, popped it back in place, replaced bracket, closed top ...Easy peasy!!!
Read more...
Your Price
$136.80
In Stock
Electrolux Range Broil Element
PartSelect Number PS439673
Manufacturer Part Number 316203301
This broil element is a genuine replacement part designed for electric ranges and ovens. Located at the top of the oven cavity, it delivers high-intensity heat for broiling functions. Compatible with various models from Frigidaire, Kenmore, Electrolux, and other associated brands, this OEM component replaces several previous part numbers and ensures reliable performance. If your oven is not reaching broil temperatures, heating unevenly, or the element appears visibly damaged, replacing it can restore proper cooking function. Installation should be performed with the appliance unplugged or the circuit breaker turned off to ensure safety.
Fixes these symptoms
- Element will not heat
- Little to no heat when baking
- Little to no heat when broiling
- See more...
Installation Instructions
Frances from Paris, TN
Broiler element would not work
First my husband cut off the circuit breaker. He then removed the two screws that held the element in place and pulled the element out about 3 inches and disconnected the two wires. The rest was easy. We were impressed at how fast the element was sent. We were told about 5 days to 7 days. The element arrived on the second day. Very please with the service and the product.
Read more...
Your Price
$99.43
In Stock
Electrolux Range Radiant Surface Element
PartSelect Number PS2361362
Manufacturer Part Number 316135401
This part is the heatsource. This surface element is for ranges.
Surface element supplies the heat to a cooking area on top of the range.
Unplug the range or shut off the house circuit breaker for the range before installing this part. Wear work gloves to protect your hands.
Fixes these symptoms
- Element will not heat
- See more...
Installation Instructions
STEPHEN from GREENBUSH, ME
9" radiant burner element stopped working.
VERY IMPORTANT! kill the circuit breaker to the unit and/or unplugged it! 2 screws hold the ceramic glass top to the lip @ top of oven--remove them and the top can be lifted up to expose all the burner elements and wiring--remove the 2 end screws that hold the retainer bracket for the burners - then remove the 2 screws that hold the burner in question to the bracket-there's also a retainer pin that needs a bit of fussing with to completely free the burner--once totally free remove the wires from the bad unit to the good unit exactly as they are situated --install new unit onto bracket with screws and bracket back to its original location on the ceramic top-put top back down and replace both anchor screws--initiate power back to unit and yeeehahh--You just saved yourself lottsa money from repair bills!!!
Read more...
Your Price
$61.55
In Stock
Electrolux Range Element 8"
PartSelect Number PS12585173
Manufacturer Part Number 5304516159
Introducing the large coil surface element from Frigidaire - a genuine, OEM part compatible with certain models of Frigidaire, Electrolux, White Westinghouse, and Tappan appliances. This element provides the necessary heat for cooking zones atop your range. Installation safely requires the range to be unplugged or the house circuit breaker switched off, and it's recommended to wear work gloves during this procedure. Included are helpful DIY instructions for electric range and cooktop installations. Please ensure to verify the part number's fit for your model before purchasing, as parts may have slight size and shape variances.
Fixes these symptoms
- Element will not heat
- See more...
Your Price
$142.44
In Stock
Electrolux Range Dual Element With Limiter
PartSelect Number PS2581859
Manufacturer Part Number 316555800
This dual radiant surface element is designed for electric ranges and cooktops, offering two heating zones—9 inches and 6 inches—to accommodate a variety of cookware sizes. It delivers consistent, even heat for efficient cooking and serves as a direct replacement for damaged or underperforming elements. Operating at 240 volts, the unit features a durable all-metal temperature control rod that enhances heat stability and longevity. Compatible with multiple models across several brands, this component is ideal for restoring optimal performance to your cooktop. Installation should be performed with the appliance disconnected from power and may require basic tools.
Fixes these symptoms
- Element will not heat
- See more...
Installation Instructions
Tom from Wallingford, CT
Burned element
Flip up top, remove wires and two screws. Replace in opposite way. Turn off power to stove first.
Read more...
Your Price
$175.20
In Stock
Electrolux Range Radiant Dual Surface Element - 9inch/12inch
PartSelect Number PS6012254
Manufacturer Part Number 316282101
This dual radiant surface element is designed to deliver flexible heating for your electric range or cooktop, accommodating both small and large cookware with its two heat zones measuring 9 inches and 12 inches in diameter. Built for efficient performance, it provides powerful heat output—up to 3000 watts at 240 volts—ensuring quick and even cooking. Ideal for replacing a worn or damaged element, it helps resolve issues such as uneven heating or a burner that no longer works. Installation requires disconnecting power at the circuit breaker and using appropriate tools; for best results, this task is recommended for an experienced repair person.
Fixes these symptoms
- Element will not heat
- See more...
Your Price
$160.45
In Stock
Electrolux Range Bake Element -3000w
2. Made a conscious decision to replace both bake element and ECB at the same time since the oven will be 10 years old next year and both have been utilized heavily over those years. Baking is a daily routine in this family, so more days without an oven was less desirable than a sure fix in one session.
3. With both parts on hand and my schedule cleared, set about making the repair:
ECB
4. Unplugged stove from wall socket.
5. Removed bottom and top back panels. The ECB replacement required the top panel removed. The bake element replacement required the bottom panel removed. The ECB replacement came with an unexpected, but welcome power filter that attached easily to the power leads and grounded into the oven frame.
6. Took a digital photo of the ECB wiring before removing any leads.
7. Detached leads from the ECB (no tools required).
8. Removed screws holding ECB to oven frame.
9. Removed ECB
10. Using a plastic drywall putty knife, very gently and carefully separated the overlay from the ECB. I had ordered an overlay with my original order because I was unsure how difficult this process would be and whether I would be effective at making the separation without damage. The overlay was still on back-order when I started the repair, so I was able to cancel that part of the order when I had completed the overlay separation without any damage to the overlay. Just go nice and easy and don't rush and you'll be able to separate the overlay from the ECB without damage.
11. Lined up and applied overlay to new ECB unit. Again, just take your time and check all the edges and corners.
12. Attached new ECB unit with applied overlay to the oven frame with the screws that had been taken out earlier
13. Connected leads to ECB, verified everything looked the same as the digital photo.
14. Without re-attaching the back panels, carefully plugged in the stove to verify connectivity to the ECB. Unplugged stove again.
Baking element:
15. Unscrewed oven bottom tray/bake element protector. There are two screws with attached washers in the back. These were very stuck, so used a squirt of WD40 on each and waited 10 minutes to loosen them up. They came out readily after that.
16. Press down on front of bottom tray. This will raise up the back of the bottom tray (like a see-saw), giving you just enough space to grasp it with your fingers and lift up. Wiggle the bottom tray past the convection fan louvers as you raise it up and back to free up the front lip. Set bottom tray aside.
17. Remove screws that hold the bake element in place against the back of the oven interior and on the bar that holds the bake element to the bottom of the oven interior.
18. Disconnect leads to the bake element from the back. You can tell which ones to remove easily if you have a helper jiggle the bake element a little from the other side while you observe the back of the stove.
19. Re-use the bar that holds the bake element to the bottom of the oven interior. Slide it off of the old bake element and carefully slide it onto the new bake element. Be careful to avoid scratches while doing this.
20. Align the bar that holds the bake element to the bottom of the oven interior with the screw holes, fasten this.
21. Adjust the bake element so that the fastener plates at the back line up with the screw holes on the back of the oven interior, fasten these.
22. Attach leads to the bake element in the back.
23. Plug in the stove and give it a test run after setting the time. In our case, with the new ECB and bake element in place, the oven reached 350 F in exactly 10 minutes. We were very happy with this.
24. Re-attach back panels
25. Done!
NOTE: You may smell a little bit of machine oil burn on the first and second uses of the oven. This burns off completely by the third use. Read more...
PartSelect Number PS1991807
Manufacturer Part Number 316505500
This bake element is designed to deliver consistent, radiant heat from the bottom of the oven cavity, supporting baking and roasting functions in compatible range models. Rated at 3000 watts, it features a durable construction with two separate coils mounted on an aluminum bracket and connects via four ¼-inch push-on wire terminals. If your oven is not heating properly or cooking unevenly, replacing the bake element can restore optimal performance. Please verify compatibility with your specific model before purchasing.
Fixes these symptoms
- Element will not heat
- Little to no heat when baking
- See more...
Installation Instructions
John from Beaverton, OR
Oven would take an hour to reach a temperature of 350 F. Broiler element worked fine.
1. Researched problem to identify components involved.2. Made a conscious decision to replace both bake element and ECB at the same time since the oven will be 10 years old next year and both have been utilized heavily over those years. Baking is a daily routine in this family, so more days without an oven was less desirable than a sure fix in one session.
3. With both parts on hand and my schedule cleared, set about making the repair:
ECB
4. Unplugged stove from wall socket.
5. Removed bottom and top back panels. The ECB replacement required the top panel removed. The bake element replacement required the bottom panel removed. The ECB replacement came with an unexpected, but welcome power filter that attached easily to the power leads and grounded into the oven frame.
6. Took a digital photo of the ECB wiring before removing any leads.
7. Detached leads from the ECB (no tools required).
8. Removed screws holding ECB to oven frame.
9. Removed ECB
10. Using a plastic drywall putty knife, very gently and carefully separated the overlay from the ECB. I had ordered an overlay with my original order because I was unsure how difficult this process would be and whether I would be effective at making the separation without damage. The overlay was still on back-order when I started the repair, so I was able to cancel that part of the order when I had completed the overlay separation without any damage to the overlay. Just go nice and easy and don't rush and you'll be able to separate the overlay from the ECB without damage.
11. Lined up and applied overlay to new ECB unit. Again, just take your time and check all the edges and corners.
12. Attached new ECB unit with applied overlay to the oven frame with the screws that had been taken out earlier
13. Connected leads to ECB, verified everything looked the same as the digital photo.
14. Without re-attaching the back panels, carefully plugged in the stove to verify connectivity to the ECB. Unplugged stove again.
Baking element:
15. Unscrewed oven bottom tray/bake element protector. There are two screws with attached washers in the back. These were very stuck, so used a squirt of WD40 on each and waited 10 minutes to loosen them up. They came out readily after that.
16. Press down on front of bottom tray. This will raise up the back of the bottom tray (like a see-saw), giving you just enough space to grasp it with your fingers and lift up. Wiggle the bottom tray past the convection fan louvers as you raise it up and back to free up the front lip. Set bottom tray aside.
17. Remove screws that hold the bake element in place against the back of the oven interior and on the bar that holds the bake element to the bottom of the oven interior.
18. Disconnect leads to the bake element from the back. You can tell which ones to remove easily if you have a helper jiggle the bake element a little from the other side while you observe the back of the stove.
19. Re-use the bar that holds the bake element to the bottom of the oven interior. Slide it off of the old bake element and carefully slide it onto the new bake element. Be careful to avoid scratches while doing this.
20. Align the bar that holds the bake element to the bottom of the oven interior with the screw holes, fasten this.
21. Adjust the bake element so that the fastener plates at the back line up with the screw holes on the back of the oven interior, fasten these.
22. Attach leads to the bake element in the back.
23. Plug in the stove and give it a test run after setting the time. In our case, with the new ECB and bake element in place, the oven reached 350 F in exactly 10 minutes. We were very happy with this.
24. Re-attach back panels
25. Done!
NOTE: You may smell a little bit of machine oil burn on the first and second uses of the oven. This burns off completely by the third use. Read more...
Related Electrolux Range Parts
- All Electrolux Range parts
- Electrolux Range Brackets and Flanges
- Electrolux Range Caps and Lids
- Electrolux Range Circuit Boards and Touch Pads
- Electrolux Range Deflectors and Chutes
- Electrolux Range Doors
- Electrolux Range Drawers and Glides
- Electrolux Range Ducts and Vents
- Electrolux Range Grates
- Electrolux Range Handles
- Electrolux Range Hardware
- Electrolux Range Hinges
- Electrolux Range Hoses and Tubes
- Electrolux Range Igniters
- Electrolux Range Insulations
- Electrolux Range Knobs
- Electrolux Range Lights and Bulbs
- Electrolux Range Motors
- Electrolux Range Panels
- Electrolux Range Racks
- Electrolux Range Seals and Gaskets
- Electrolux Range Sensors
- Electrolux Range Springs and Shock Absorbers
- Electrolux Range Switches
- Electrolux Range Thermostats
- Electrolux Range Trims
- Electrolux Range Valves
- Electrolux Range Wheels and Rollers
- Electrolux Range Wire Plugs and Connectors