Washer Hoses and Tubes

Your Price

$26.17

Drain Hose

★★★★★

52 Reviews

PartSelect Number PS890597

Manufacturer Part Number WH41X10096

The drain hose is black in color and made of flexible material. This is a part for your top-load washer. The hose measures 57 inches long. This part moves the water out of the washer and into the drain. If this parts cracks or becomes damaged it will leak during the drain cycle of your wash and you may find water on the floor. To access the hose, you will need to move the washer away from the wall to get to the back of the appliance. There will be two screws holding it in place that will need to be removed.

Fixes these symptoms

Leaking
Will not drain
See more...

Installation Instructions

Anthonie from Beale AFB, CA

Old Hose Had A Leak

First I removed the screws that held the hose drain hose clip in place. Removed the damaged hose. Placed the new drain hose clip at the end of the new drain hose. Re-inserted back in hole, pushed in hose to necessary depth then tighted screws, Very easy and painless. Read more...

Your Price

$24.09

Washer Drain Hose

★★★★★

13 Reviews

PartSelect Number PS12578897

Manufacturer Part Number W11244231

The drain hose carries used water from the washer to your house drain.

Fixes these symptoms

Leaking
See more...

Installation Instructions

Delmar from EAST TROY, WI

replaced drain hose that was missing

slipped the new drain hose on and with locking plyers slipped the wire clap in place after three trys Read more...

Your Price

$49.39

Faucet Adapter

★★★★★

21 Reviews

PartSelect Number PS11751238

Manufacturer Part Number WPW10254672

The faucet adapter for your portable dishwasher or washing machine attaches to the faucet and allows you to connect the machine to the tap. Before you install the faucet adapter on your taps, be sure that it fits the coupler on your dishwasher or washer. As per the factory, this is used for faucets with inside or outside threads. For female connection (outside) just remove the washers. This adapter is approximately 1 inch in length, and slightly less than one inch in diameter. This adapter comes with two different thicknesses of rubber washer. You will not need to use both so be sure to determine which thickness works best for your tap before installing it.

Fixes these symptoms

Leaking
Will not fill with water
See more...

Installation Instructions

Stephen from Enfield, CT

faucet attachment would not sit correctly in hose connector to portable dishwasher. Received machine second hand. Could not find a replacement faucet adapter. So ordered new one and hose plus connector.

Turned machine on side. Removed two casters with Wonder Tool prybar. Then used it to remove plastic push screws holding cardboard bottom cover. Unscrewed water hose. Used screwdriver to remove clamp on drain hose. Stood machine upright, opened door. Unscrewed two screwsfrom tabs into woodblock top. Slid top forward and removed it. Cut plastic hose retainer. Removed hose assembly. Installed new hose by reversing steps. Used a new wire strap to hold hoses in place on top corner of machine. Read more...

Your Price

$37.60

Drain Hose

★★★★★

25 Reviews

PartSelect Number PS11753688

Manufacturer Part Number WPW10358149

It connects from the pump to the back panel. The clamp is not included.

Fixes these symptoms

Leaking
See more...

Installation Instructions

Esther from Santa Ana, CA

Drain hose had a leak

The repair was so easy. The part came quickly and with easy to follow directions. I am a woman and a single parent; needless to say, I don't have time or money to waste. This repair cost me under $30 and under 30 minutes to fix. Thank you again! Read more...

Your Price

$20.59

Rubber Injector Valve

★★★★★

33 Reviews

PartSelect Number PS11738945

Manufacturer Part Number WP216201

This part is commonly known to cause a leak at the top left corner of the outer tub. It fits over the injector nozzle. It is black in color and measures approximately 2 inches in length. To access this part, you will need to remove the front panel of your washer. There will be 2 screws holding it in place. Once these have been removed, the top will pivot to open, which will give you access to the injector assembly. This is an OEM part that comes right from the manufacturer and is sold individually.

Fixes these symptoms

Leaking
See more...

Installation Instructions

Catherine from Wyandotte, MI

Front load washing machine leaking on floor while in fill mode.

Removed two screws at bottom of front panel and then removed front panel. Then removed two self-tapping bolts (one on each side) holding top panel in place and swung the panel up, out of the way, to expose top of tub and water injection components. Cut off one pinch clamp and loosened screw clamp holding two injector hoses to the injector sleeve. Removed these water injector hoses from injector sleeve assembly which is mounted on top of left side panel upper flange. Replaced deteriorated rubber injector valve, nozzle and the sleeve for the injector (plastic housing containing the injector valve and nozzle). Also replaced deteriorated injector tube seal where injector tube elbow mounts to top of tub assembly. Reinstalled injector hoses with a replacement screw clamp to replace the one cut off. tightened the new clamp and the other, original, screw clamp and checked for leaks. This solved the leakage problem. Secured top panel and re-installed front panel. Hardest part of the task was determining where the leak emanated from but once found and parts ordered, it was a relative snap to fix. Read more...

Your Price

$30.26

Washer Hose with Bellows

★★★★★

6 Reviews

PartSelect Number PS3523347

Manufacturer Part Number 4738ER1004B

This washer hose with bellows, also known as a dispenser hose, is a genuine OEM replacement part for your washer. Replacing this part can be helpful if your washer is leaking. The dispenser hose connects the dispenser assembly to the tub. Before beginning the repair, unplug the washer and turn off the water supply. You will need a Phillips head screwdriver to complete this repair; a clamp tool can also be helpful. Remove the screws holding the lid of the washer in place, and take off the lid. Locate the dispenser hose and remove its clamps. Place the clamps on the new hose, using the arrows for a guide in positioning the clamps. Install the new hose and reassemble all other parts.

Fixes these symptoms

Leaking
See more...

Installation Instructions

mark from AUBURN, CA

LG washing machine flooded the Landry room.

Wife called me and said the washing machine just flooded the Landry room. I looked at it and didn't see anything wrong. Took the top off and the back off and started looking for a leak, did not see anything. Took the front part of the washer apart thinking the drain hole was plugged up where the rubber boot is. It was ok after taking the big rubber boot off or whatever that is called i was not getting anywhere. I put it back together left the top and the back off. I turned the water on and started the washer on a quick cycle looking for a leak. I found the bellows at the inlet had a small leak fixed that and started the washer again. So what i found out was the clean out drain plug was not in tight letting water out as it was washing after i tightened it all was ok. So i did find a leak that was small that we never saw. The hardest part was putting that wire clamp on the rubber boot it took two people to do that. Read more...

Your Price

$36.86

Tub-to-Pump Drain Hose

★★★★★

14 Reviews

PartSelect Number PS3523345

Manufacturer Part Number 4738ER1002A

This is a tub-to-pump drain hose for a front load washer. The hose features flexible bellows which allow it to expand and contract when necessary. It carries the water from the tub of the washer to the drain pump so the used water can properly empty from the tub. This part is made of rubber, is black in color and measures 13 inches long. Be sure to drain the excess water from the washer before completing this repair. This is an authentic OEM part that is sourced directly from the manufacturer.

Fixes these symptoms

Leaking
Will not drain
See more...

Installation Instructions

Leslie from STOWE, VT

leaking tub-to-pump drain hose

Pull washer away from wall. Unplug cord and remove drain hose from receptacle. Remove 4 screws holding panel to rear of washer. Squeeze and slide back hose clamps on each end of drain hose and loosen center clamp with screwdriver. Remove old hose. Reinstall new hose in reverse order using existing clamps. Re-install back panel. Read more...

Your Price

$21.24

Water Inlet Hose

★★★★★

6 Reviews

PartSelect Number PS11741209

Manufacturer Part Number WP3357328

This part is the replacement water inlet hose for your washer. It is black in color, made of plastic, and is approximately 19 inches long. The water inlet hose connects the water inlet valve to the water fill nozzle. Over time the hose can become cracked and damaged, and this can cause it to leak. A damaged hose will need to be replaced. Be sure to disconnect the water supply to the washer before you begin this repair. You should also determine if any of the other parts that transport water into the washer are leaking, and if they need to be repaired as well. This part is sold individually and is a genuine OEM part.

Fixes these symptoms

Leaking
See more...

Installation Instructions

Timothy from Springfield, VA

Cold water flowed slowly

First, be sure to take the washer apart properly! The first time I fixed my washer I took it apart the hard way to change the clutch, and believe me it took longer to put it back together!
This time I was replacing both the water inlet valve and the hose leading to the disperser.
First remove the two screws holding down the control panel. It then flips back and hangs out of the way behind the washer. Then remove the spring-clip holding the rear plate to the body of the washer, one on each side under the control panel.
Next you need to remove the screws holding the body down to the base at the rear of the machine.
I then tipped the body of the washer forward and let it rest on a bucket so I didn't have to take it completely off. Then it is easy to access the hose and the water inlet valve. Shut off the water and remove the supply hoses to the washer. Remove the two screws holding the water inlet valve to the rear of the washer using a nut driver. Next remove the wires to teh inlet valve, making sure to note which one is cold and hot, and which orientation they are. Mine was yellow on top and brown on bottom. Next remove the springs clamps holding the hose on. Replace the hose re-using the same clamps. Replace the water inlet valve reverse the process to re-assemble the washer. Tilt the body back on, put the screws in the base, clamp the back to the body, flip the contorl panel back over and insert the screws. Reattach the water supply lines and you are done! Read more...

Your Price

$32.58

Washer Tub-to-Pump Hose

★★★★★

2 Reviews

PartSelect Number PS11765836

Manufacturer Part Number W10899966

The tub-to-pump hose carries the water from the tub to the drain pump. Unplug the washer and shut off the water supply before installing this part. Wear work gloves to protect your hands

Fixes these symptoms