Estate Washer Hoses and Tubes
Popular Estate Washer Hoses and Tubes
Your Price
$38.89
In Stock
Estate Washer Drain Hose
PartSelect Number PS11753688
Manufacturer Part Number WPW10358149
It connects from the pump to the back panel. The clamp is not included.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Esther from Santa Ana, CA
Drain hose had a leak
The repair was so easy. The part came quickly and with easy to follow directions. I am a woman and a single parent; needless to say, I don't have time or money to waste. This repair cost me under $30 and under 30 minutes to fix. Thank you again!
Read more...
Your Price
$21.90
In Stock
Estate Washer Water Inlet Hose
This time I was replacing both the water inlet valve and the hose leading to the disperser.
First remove the two screws holding down the control panel. It then flips back and hangs out of the way behind the washer. Then remove the spring-clip holding the rear plate to the body of the washer, one on each side under the control panel.
Next you need to remove the screws holding the body down to the base at the rear of the machine.
I then tipped the body of the washer forward and let it rest on a bucket so I didn't have to take it completely off. Then it is easy to access the hose and the water inlet valve. Shut off the water and remove the supply hoses to the washer. Remove the two screws holding the water inlet valve to the rear of the washer using a nut driver. Next remove the wires to teh inlet valve, making sure to note which one is cold and hot, and which orientation they are. Mine was yellow on top and brown on bottom. Next remove the springs clamps holding the hose on. Replace the hose re-using the same clamps. Replace the water inlet valve reverse the process to re-assemble the washer. Tilt the body back on, put the screws in the base, clamp the back to the body, flip the contorl panel back over and insert the screws. Reattach the water supply lines and you are done! Read more...
PartSelect Number PS11741209
Manufacturer Part Number WP3357328
This part is the replacement water inlet hose for your washer. It is black in color, made of plastic, and is approximately 19 inches long. The water inlet hose connects the water inlet valve to the water fill nozzle. Over time the hose can become cracked and damaged, and this can cause it to leak. A damaged hose will need to be replaced. Be sure to disconnect the water supply to the washer before you begin this repair. You should also determine if any of the other parts that transport water into the washer are leaking, and if they need to be repaired as well. This part is sold individually and is a genuine OEM part.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Timothy from Springfield, VA
Cold water flowed slowly
First, be sure to take the washer apart properly! The first time I fixed my washer I took it apart the hard way to change the clutch, and believe me it took longer to put it back together!This time I was replacing both the water inlet valve and the hose leading to the disperser.
First remove the two screws holding down the control panel. It then flips back and hangs out of the way behind the washer. Then remove the spring-clip holding the rear plate to the body of the washer, one on each side under the control panel.
Next you need to remove the screws holding the body down to the base at the rear of the machine.
I then tipped the body of the washer forward and let it rest on a bucket so I didn't have to take it completely off. Then it is easy to access the hose and the water inlet valve. Shut off the water and remove the supply hoses to the washer. Remove the two screws holding the water inlet valve to the rear of the washer using a nut driver. Next remove the wires to teh inlet valve, making sure to note which one is cold and hot, and which orientation they are. Mine was yellow on top and brown on bottom. Next remove the springs clamps holding the hose on. Replace the hose re-using the same clamps. Replace the water inlet valve reverse the process to re-assemble the washer. Tilt the body back on, put the screws in the base, clamp the back to the body, flip the contorl panel back over and insert the screws. Reattach the water supply lines and you are done! Read more...
Estate Washer Break Hose
PartSelect Number PS11745951
Manufacturer Part Number WP8317926
This hose goes from valve to inlet.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
JANET from GERMANTOWN, NY
The water intake hose had a hole and was leaking. I think a rat chewed it.
I first watched a YouTube video on how to open up the machine. It was a breeze. I removed the part the hose attaches to where the water comes out and into the tub. The hardest part was removing the old hose clamps. Had I known I would have used new clamps. I took off old hose and replaced with the new one, it took longer because of the clamp issue. Otherwise it went fairly easy, to my surprise. Even tho I am a 70 yr old woman I will try to fix what I can. Doing this saved me at least $600. For a new washing machine. I'm so proud of myself.
Read more...
Your Price
$21.27
In Stock
Estate Washer Tub-to-Pump Hose Kit
PartSelect Number PS334685
Manufacturer Part Number 285871
This kit comes with the clamps.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Marc from Morton Grove, IL
Two leaking hoses in my washing machine
Put the machine on its side. Remove old hoses and screw new ones into place. Done in under 20 minutes.
Read more...
Your Price
$46.70
In Stock
Estate Washer Drain Hose
PartSelect Number PS11748248
Manufacturer Part Number WPW10096921
This drain hose is 42" long and includes the clamps.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Francis from Yuba City, CA
I bought a used washer from a friend and they had cut the drain hose short .
I got a pair of channel lock pliers and took off clamp on the hose, after laying wash machine on it's side, poped off a few little clips and replaced the hose, and now everything works perfect.
Read more...
Your Price
$48.02
In Stock
Estate Washer HOSE-DRAIN
PartSelect Number PS11749880
Manufacturer Part Number WPW10189267
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
John from MT PROSPECT, IL
Very little hot water was the problem
I followed the video you guys sent me. You guys and woman are the best!
Read more...
Your Price
$21.51
In Stock
Estate Washer Inlet Hose - 5 FT
PartSelect Number PS11746820
Manufacturer Part Number WP89503
This hose can handle hot or cold water and is five feet long.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Helen from NASHUA, NH
Your Price
$48.51
In Stock
Estate Washer Drain Hose with Clamp
PartSelect Number PS334596
Manufacturer Part Number 285664
Used to drain water.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Steve from Cypress, CA
Leaking drain hose
First I removed hose from drain, next I loosened the clamp at the drain hose connection at the washer. Removed hose. Have rags/towels as there is some residual water that will spill out of the washer. Reinstall in reverse.
Read more...
Estate Washer Drain Hose
PartSelect Number PS334597
Manufacturer Part Number 285666
This drain hose is 10 feet long and comes with a clamp.