Estate Washer Hardware
Popular Estate Washer Hardware
Your Price
$7.03
In Stock
Estate Washer Agitator Bolt
PartSelect Number PS11741866
Manufacturer Part Number WP358237
This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".
Fixes these symptoms
- Leaking
- Marks left on clothes
- Spinning Issues
- See more...
Installation Instructions
Dexter from Milwaukie, OR
Washer made a loud banging noise at end of spin cycle, leaked water and agitator seemed loose
After entering the model number of your appliance you will be taken to a page where all of the parts are displayed by sections. On that page about in the middle there is a heading called "Find Part By Symptom." I figured out from there which symptom the washer had and read what other people were saying and how they made the repairs. Basically I had three problem areas, Noise, Leaking and a problem with the agitator. I focused on the loud noise first and decided I needed to replace the clutch/brake assemblies. I found the clutch parts page and on that page there was a video on how to make this repair. This video is all you need to gain access to all moving parts located under the cabinet. Which ever part you are replacing, I recommend watching this video! After removing the console, back panel and cabinet then laying the machine on its back just as seen on the video, I had access to the water pump, motor, transmission and related clutch/brake parts. As it turned out I did not need the clutch/brake assembly but as a precaution and because the parts were cheap, I replaced the motor coupling, water pump and tub wear pads. I decided to replace the agitator assembly because of several worn parts associated with the dog ears/drive shaft ETC. I put the machine back upright and took off the top cap on the agitator, then there is an inner cap with seal that gives access to the 7/16" bolt you must remove to remove the agitator. However once the agitator was removed I noticed metal shavings and play in the shaft. I used a spanner wrench to remove the spanner nut. I removed the Plastic Tub Ring (has several clips around the outer tub), then removed the inner washer tub to replace the Drive Block. Replacing the Drive Block stopped the loud noise at the end of the spin cycle. Now just reverse the order to put the machine back together and your done. For my situation it was best to take the machine apart and decide which parts I needed before ordering to minimize errors. These machines are made very cheaply and are designed to brake at some point in time and it is very easy to determine which parts are worn because most are made of plastic. In this process I also noticed where my leaks (did I say Leaks) were coming from. There were two hose clamps installed improperly from the factory, so check all clamps, hoses ETC. and you should be good to go.
Read more...
Estate Washer Screw, 8/18 x 3/8
PartSelect Number PS11746840
Manufacturer Part Number WP90767
This screw is sold individually.
Installation Instructions
Alexander from Lakeland, FL
Broken Dryer Knob
First let me just say that Partselect.com is now one my stored favorites in my web browser. I came home from a business trip and saw a pair of pliers on the dryer. I thought that was odd until my wife informed me that the knob on the dryer had broken. So she was using the pliers to select the cycle. Somehow she knew where the missing pointer was actually pointing. Since the dryer was over 5 years old I saw this as an opportunity to upgrade both appliances. Not with my frugal wife. A search of the Internet popped up partselect. I ordered Wednesday morning and the parts where on my doorstep late Thursday. Trust me I was very surprised. Everything worked perfectly. Two thumbs up!!!
Read more...
Estate Washer Cover Screw
A licensed electrician had also moved the power line over to the new location and left a wire sticking out of the bottom of the wall to hardwire the dishwasher in again. We decided to convert the dishwasher to be able to be plugged into a standard 20amp wall outlet instead. We had already purchased a kit with a nice long cord and strain-relief snap on plastic fitting that snapped onto the metal incoming power box on the bottom front of the dishwasher. Using the supplied wire nuts, etc., we connected the wires and ground wire to the proper wires from the dishwasher and ground lug. We put the dishwasher aside and then went to work on converting the power wire coming out of the bottom of the wall, to a conventional outlet. I am mentioning all this because in our first attempt we unfortunately put the receptacle a bit high off the floor and the new power cord plug end, stuck out and hit the back of the dishwasher so it would not go all the way in and was sticking out from under the counter top. I tried using one of those flat adapter cables, but even that still stuck out to far. So we ended up relocating the outlet box as low as we could on the wall and this allowed the plug to stick out into the opening area at the bottom rear area of the dishwasher so it could now be slid all the way in under the kitchen counter properly. I hope that bit of trial and error will save you some time if you ever decide to go the pluggable route too.
The new installation required the use of the dishwasher side mount brackets, so we had to purchase a replacement set of those, complete with the hardware to screw them down.
This project took a bit longer than planned due to the power plug problem, one which we will remember for any other similar appliance relocation projects, as well as the time to get our new parts in that we had to order, but other than that the rest went smoothly and the dishwasher was relocated successfully. Read more...
PartSelect Number PS11740701
Manufacturer Part Number WP308685
Sold individually.
Installation Instructions
Curtis from PALM BAY, FL
Relocating dishwasher into the new kitchen layout
In this case the dishwasher had already been installed for a few years. After removing it, we inspected it and saw it needed a bit of TLC. The transport wheels on the back were missing, making it harder to move around without scratching the tile and some of the original hardware was rusted or broken off. I looked up the parts easily here on PartsSelect using their parts breakdown diagrams and was glad to see what I needed was still available. We had a licensed plumber relocate the hot water line and drain for us to make things a bit easier.A licensed electrician had also moved the power line over to the new location and left a wire sticking out of the bottom of the wall to hardwire the dishwasher in again. We decided to convert the dishwasher to be able to be plugged into a standard 20amp wall outlet instead. We had already purchased a kit with a nice long cord and strain-relief snap on plastic fitting that snapped onto the metal incoming power box on the bottom front of the dishwasher. Using the supplied wire nuts, etc., we connected the wires and ground wire to the proper wires from the dishwasher and ground lug. We put the dishwasher aside and then went to work on converting the power wire coming out of the bottom of the wall, to a conventional outlet. I am mentioning all this because in our first attempt we unfortunately put the receptacle a bit high off the floor and the new power cord plug end, stuck out and hit the back of the dishwasher so it would not go all the way in and was sticking out from under the counter top. I tried using one of those flat adapter cables, but even that still stuck out to far. So we ended up relocating the outlet box as low as we could on the wall and this allowed the plug to stick out into the opening area at the bottom rear area of the dishwasher so it could now be slid all the way in under the kitchen counter properly. I hope that bit of trial and error will save you some time if you ever decide to go the pluggable route too.
The new installation required the use of the dishwasher side mount brackets, so we had to purchase a replacement set of those, complete with the hardware to screw them down.
This project took a bit longer than planned due to the power plug problem, one which we will remember for any other similar appliance relocation projects, as well as the time to get our new parts in that we had to order, but other than that the rest went smoothly and the dishwasher was relocated successfully. Read more...
Your Price
$7.38
In Stock
Estate Washer Suspension Spring Retainer
PartSelect Number PS11749057
Manufacturer Part Number WPW10145155
This is a replacement suspension spring retainer for your washer. The retainer holds the suspension spring in place while the washer is operating. If you notice movement, or an unusual noise or shaking of your washer when it is in use, it could mean that the suspension spring has been disconnected because of a broken or missing spring retainer. You will find the suspension spring retainer at the bottom of the tub assembly. To replace the retainer, use a pair of pliers to disconnect the suspension spring from the chassis mount to relieve the tension. Then, remove the spring from the retaining clip, and remove the retaining clip from the bottom of the washer. Attach the new retaining clip to the bottom of the washer, reattach the spring, and stretch it slightly so it can connect to the chassis. This part is sold individually.
Installation Instructions
RUSSELL from SOUTHOLD, NY
machine was out of balance
Removed the washing machine from the wall and found a broken spring on the floor. Began disassembling the unit before accessing your sight. (Later I viewed your video of the more simple dis assembly).Used your parts breakdown to identify the 6 parts I needed (3 springs and 3 retainers),and ordered them. They arrived on time and as per the video, installed them with ease and reassembled the unit. My wife is very happy. Thank you, Rusty
Read more...
Your Price
$11.77
In Stock
Estate Washer Hose Clamp
PartSelect Number PS11743008
Manufacturer Part Number WP596669
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This clamp is used to securely attach a hose to another part of your appliance, which helps prevent leaks from those connections. Depending on the appliance, it can attach hoses to drain pumps, water inlet valves, pressure switches, and injector nozzles. We recommend you refer to model-specific diagrams for appropriate uses and exact placement. This hose clamp is made of metal, and is sold individually. To access and replace this part you will need a nut driver, pliers, and screwdrivers. Before you begin any repair work, make sure you have unplugged your appliance, and shut off the water supply if applicable.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
jeff from lindenhurst, IL
Washing Machine was leaking water
Loosened the hose clamp, removed the injector valve and injector nozzle assembly, replaced both and tightened with new hose clamp. Fixed the problem for less than $20!! Washing machine is 20 years old and this was the first problem--hopefully it is now good for another 20 years!
Read more...
Estate Washer Screw
PartSelect Number PS11742721
Manufacturer Part Number WP488729
Metallic screw that is less than an inch long. Does not include the plastic washer.
Installation Instructions
Kyle from Wimauma, FL
Black Cam was bren on lower door hinge
This was a very simple job. Remove the top Hinge bracket, a total of 4 screws, lifted the door off the bottom hinge, removed the bottom hinge set up, 2 screws, replaced it, and attached the new bottom black door cam, lifted the door back onto the bottom hinge and aligned the top hinge, and reinserted the screws, and Ta Da, The door works like a new refrigerator door. 15 to 30 min tops. I did not even have to take the refrigerator items out of there door holder.
Read more...
Your Price
$252.75
In Stock
Estate Washer Gearcase
PartSelect Number PS341974
Manufacturer Part Number 3360629
This is used in your direct drive washer that has a neutral drain.
Fixes these symptoms
- Leaking
- Will not agitate
- See more...
Installation Instructions
Troy from Storm Lake, IA
Tub wouldn't turn, but motor would allow it to drain.
I took the two screws for the control panel out and tilted it up and back. Then remove the two metal clips which held the outer panel to the back panel. After disconnecting the power and water I tipped the washer on its back. I had to remove two clips to take the water pump off of the motor, then removed the two screws and clips which held in the motor. After removing the motor, I found the coupler was bad. To remove the gearcase, I took out the softener dispenser and removed one bolt to take out the agitator. Under the agitator was a clip. Three bolts held the gearcase to the frame. After removing them, the gearcase pulled straight out the bottom. Replacement was just a reverse process, with the addition of a light coat of grease to the gearcase shaft.
Read more...
Your Price
$11.09
In Stock
Estate Washer Hose Clamp
PartSelect Number PS11740613
Manufacturer Part Number WP285655
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installation, you will need a flat head screw driver to replace the clamp and a drill to access the screws to remove the front of the washer. Be careful if you do not have specific clamp pliers as the clamp could fly off. Once the front of the washer has been removed, take a quick look for water damage or any obvious signs of where the leak is coming from. If it is not obvious, run water to test.
Fixes these symptoms
- Leaking
- Will not drain
- See more...
Installation Instructions
Stephen from Laveen, AZ
Drive Pump Leaked
It took some trial and error but overall not a difficult project. 1. Take the front covers off. 2. Undo the pully spring to loosen belt 3. Remove belt off idler pulley wheel and free up belt from the large wheel. 4. Disconect the wiring harness and the hoses. 5. Undo the motor mounting bolts (4) 6. Take motor out of washer and remove the 3 screws holding the pump to the motor. 7. The pump had melted to the shaft and required I chisel the pump off of the shaft. 8. Attach new pump paying attention to where the belt is positioned. 9. Reattach the motor bolts, hoses, and wiring harnes. 10. Attach the belt and test the pump. 11. Put the front back on.
Read more...
Estate Washer Spanner Nut
PartSelect Number PS11738884
Manufacturer Part Number WP21366
Right hand threaded nut holds the tub in place in direct drive, top loading washing machines. To remove the spanner nut you will need a spanner wrench.
Fixes these symptoms
- Leaking
- Will not agitate
- See more...
Installation Instructions
Diane from BALTIMORE, MD
Washer was leaking.. determined it was center gasket
Completely dismantled washer per video , replaced gasket and spanner nut, then re-assembled washer. I’m a 58 year old female. It was tough. Main issue was that video was for dif. Model washer. Had to figure out some things myself.
Read more...
Your Price
$10.97
In Stock
Estate Washer Pump Retainer
PartSelect Number PS11746362
Manufacturer Part Number WP8546127
Sold Individually.
Fixes these symptoms
- Leaking
- Will not drain
- See more...
Installation Instructions
Tom from Granby, MA
Water pump leaking when machine used.
The hardest part of this job was pulling the machine away from the wall so the hoses could be disconnected and the machine flipped onto it's back. Putting the machine on it's back does two things. It drains the water left in the bottom of the tub so it won't pour out onto the motor when the old pump is removed, and gives the necessary access to the pump. Once the machine is on it's back you remove the hose clamps with a pair of pliers and disconnect the hoses. The pump is secured to the motor with a pair of spring steel retaining clips which are easily popped off by hand. Once the clips are removed, the pump is in your hand. Put the new pump in place, replace the retaining clips and hoses, and you're done. This has to have been the easiest repair I've ever done. I wish cleaning gutters was this easy.
Read more...