Gibson Washer Hoses and Tubes

Videos!

Your Price

$20.60

Gibson Washer Drain Hose

★★★★★

11 Reviews

PartSelect Number PS417877

Manufacturer Part Number 131461200

This drain hose is designed for use in your washer. The function of this part is to carry water from the drain pump to the house drain. If your washer is leaking or will not drain, you may need to replace the drain hose. This part is black in color and is made of plastic. This drain hose comes with a 90-degree elbow attachment. Before you begin this repair, be sure to disconnect the power supply, as well as the water supply to the washer. This part is sold individually. This is an OEM part sourced directly from the manufacturer.

Fixes these symptoms

Leaking
Will not drain
See more...

Installation Instructions

Carl from Wilmington, DE

Drain hose was leaking due to small hole in hose

This is the third time I have ordered parts from this company .I can't say enough good things about them from their fast shipping( always arrives sooner than they state)To the quality of the parts and the shipping packages.A first class operation from start to finnish.First step was to disconect power supply.Second was to remove washer drain hose from house drain.Third remove two (2) phillips head screws from front cover of washer ,located at bottom right and left side of front panel near floor.Lift front panel up to unhook metal retainers on panel that connect it to washer side panels.Use pliers to remove spring clamp from hose. Remove hose from washer pump. Remove clamp from hose,remove plastic retainer holding hose to washer bottom.Feed hose out the back of the washer through washer drain hose hole in the back pannel of the washer.Remove plastic retainer.Insert the new hose through the hole in the back pannel install the hose clamp and install the hose back on the pump.Relocate clamp on hose, take front panel,lift into place,push down to lock retaining taps into side cover slots replace the two phillips head screws. Read more...

Your Price

$70.68

Gibson Washer Drain Hose

★★★★★

3 Reviews

PartSelect Number PS1524515

Manufacturer Part Number 134592700

This drain hose, used in washing machines, delivers water from the drain pump to the house drain. The hose is 7 1/2 feet (90 inches) long. If your hose is leaking, it is best to replace it with a new one. To repair it, first access the back of the washer and remove the clamp holding the hose. Switch the clamp onto the new hose before placing it back into the fitting. Refer to the manual provided by the manufacturer for further instructions and guidance. Remember to unplug the appliance from the power source before beginning installation.

Fixes these symptoms

Leaking
See more...

Installation Instructions

Edward from New Smyrna Beach, FL

water leaking on floor

Removed two screws at bottom of front panel, removed front panel. Used pliers to remove hose clamp on drain hose. Fished hose out of chassis and installed new hose. Tested for leaks. Read more...

Videos!

Your Price

$90.92

Gibson Washer Tub-To-Pump Hose

★★★★★

5 Reviews

PartSelect Number PS418742

Manufacturer Part Number 131784700

Fixes these symptoms

Leaking
See more...

Installation Instructions

Larry from East Point, KY

Washer would leak water out the bottom.

First I removed the two screws holding the front panel on and removed the panel. The hose is held on by two spring clips and a hose clamp. After getting those out of the way, I removed the damaged hose and slid the new one into place and fastening it down with the aforementioned clips and clamp. Read more...

Your Price

$57.17

Gibson Washer Pump to Tub Hose - Black

★★★★★

1 Review

PartSelect Number PS417966

Manufacturer Part Number 131494800

Fixes these symptoms

Leaking
See more...

Installation Instructions

Dixie from STRANG, OK

Leaking hoses

I made my job difficult by removing the back panel, then the side, and finally discovered the front panel opens giving access to the washer. Using heavy pliers I removed the spring clamps and replaced the pump to washer hose and the other hose end to the tub. Turned on the washer no leak only to discover the drain hose had developed a leak. So I ordered the second hose. I was not sure how to release the plastic retaining clamps. Finally just yanked them loose, which worked. Ran the hose through the machine out the back into the drain pipe. I was able to reattach the retaining clamps put the spring clamp on the pump end of the hose. The difficult part was getting the back, sides and front of the washing machine together that took hours. Read more...

Your Price

$2.38

Gibson Washer Hose Clamp

PartSelect Number PS466832

Manufacturer Part Number 5303318539

Sold individually.

Fixes these symptoms

Leaking
See more...

Installation Instructions

David from SPRING HILL, FL

Original hose needed replacement due to leaking holes

The replacement hose was not as long and the original and therefore did not fit into the track made for the original one. Though it was long enough to work, an additional 4 inches would have been an exact fit.
As a result, the replacement had to be duct taped to the side of the dishwasher to hold it in place. Otherwise, the new hose was of better quality that the flimsy original. All in all, I could have picked up 3 feet of rubber hose from an auto parts or hardware store cheaper and done the job just as well, if not better. Read more...