Maytag Dryer Belts

Find your part

Enter your model number or a part number and click "Search"
Need help finding your model number?
Maytag Appliance Parts
Shop By Part Type

Popular Maytag Dryer Belts

Your Price
$16.60
  In Stock
Multi Rib Belt - 92-1/4"
★★★★★
★★★★★
(353)
PartSelect Number PS346995
Manufacturer Part Number 341241
This dryer drum belt (Whirlpool Dryer Belt, Drive Belt) has four ridges, three grooves and is 1/4" wide, and 92 1/4 inches in length. It comes in black and is made of rubber. The belt transfers the rotation of the motor to turn the drum. The belt attaches to the drum, idler pulley, and motor pulley.
Fixes these symptoms
  • Heat stays on after drum has stopped
  • No heat or not enough heat
  • Noisy
  • See more...
Installation Instructions
Ray from Denton, TX
Dryer tub belt broke
Removed the two screws that attatch the lent channel to the top of the dryer, then lifted the top of the dryer by pushing in on the two locking tabs located at the front , left and right , corners of the dryer top with a small flat head screw driver. The top of the dryer will fold back out of the way. At this point I removed the two 1/4 inch screws that are located on the inside of the dryer front left and right corners that hold the front panel/door to the two side panels. Now I was able to lift the front panel up and set it to the side. The bottom of the front panel that contains the dryer door that I just removed was held on the bottom by two clips that slide into slots on the front panel and did not require any removal to disconnect the bottom of the front panel, just pull up on the front panel. Since the tub was held in place by floating on a seal at the back of the dryer and a seal on the front panel , which I just removed the tub is now free floating except for the two alignment roller wheels at the bottom of the tub. It is easier if you lay the dryer on its back at this point with front of the tub pointing up. I pulled the tub out and cleaned the years of built up lent and removed all the pieces of the old , destroyed, belt. Note, the belt tentioner is located at the front of the motor which on the bottom right hand side. If your belt is broke like mine the tensioner may/will fall to the back of the dryer when you tilt it back, but do not worry. Once the dryer was cleaned up I put the tub back in place , still on its back and made sure the two alignment rollers were in place and rolled freely when the tub was turned by hand. Another note, my original belt tensioner did not have a rolling wheel that the belt rode on , but was a semi-circle smooth surface that the belt remained in constant friction with when the dyer was running, so I made sure the replacement tensioner I ordered with my new belt did have a rolling wheel that the belt would ride on, which I believe will reduce wear and extend the belt life. The new belt came with a diagram of the belt and tensioner routing which was helpful. Note: do not take the tensioner wheel off/apart when trying to route the belt. Follow the instructions routing diagram. The tensioner is held in palce by inserting the bottom back half into the slot in the bottom floor of the dryer making sure it is aligned with the belt pully on the shaft of the dryer motor. The dryer is still on its back side. Now, it was easier for me to route the belt around the center of the tub, following the marks from the original belt, and hold in in place in a few spots with masking tape and then route it thru the tensioner and onto the front pully of the motor. Make sure you have the grooves of the belt against the tub and the grooves are aligned with the pully on the motor. Now you can remove the masking tape that was holding the belt around the tub and spin the tub by hand watching the belt making sure it is not in a bind and is traveling around the motor pully , tensioner and tub freely. Make sure the tub is still sealed on the back side wall. As you turn the tub by hand you can adjust the belt by hand so that is following the original marks around the tub left by the orignal belt. Also double check the two alingment rollers and make sure they are spinning and on track. Now put the front panel with the door on by sliding it onto the two clips that are one the bottom at each side and put the two screws in that hold the front panel to the two side panels. Now stand the dryer back up and spin the tub by hand again making sure it has a good seal on the back side and on the front panel. Pull the top back down and put the two screws in that hold the lent channle to the top. I am not sure when the belt started failing on my dryer, but was amazed at how quiet it runs now. Guess I was use to the extra noise made by a dryer that was about to die. This was a cheap and easy repair and glad I did it myself. Read more...
Your Price
$51.76
  In Stock
Dryer Repair Kit
★★★★★
★★★★★
(178)
PartSelect Number PS373088
Manufacturer Part Number 4392067
This dryer repair kit contains a multi rib dryer belt (part #661570V), 4 drum support rollers, 1 idler assembly, 9 tri rings, and 1 washer. In order to install this kit, you will need a 1/4 inch nut driver, a long flat-blade screw driver, a short flat-blade screw driver, and a Phillips screw driver. Make sure to disconnect power to the dryer before beginning this repair. Note: Please research drive belt by model number.
Fixes these symptoms
  • No heat or not enough heat
  • Noisy
  • Takes too long to dry
  • See more...
Installation Instructions
jason from HOLDEN, MA
very loud squeeling sound
The issue was the idler pulley. First I began opening up the front panel based on a youtube video but soon realized the model was slightly different and required a lot more items to remove. I saw the pulley in the back with nothing in the way so I put the front panel crap back on and removed the rear panel. There it was, very simple to remove and replace. I'm not looking forward to drum rollers though. Hopefully they're aren't as difficult as they appear. Read more...
Your Price
$31.44
  In Stock
Tumbler and Motor Belt
★★★★★
★★★★★
(136)
PartSelect Number PS11757542
Manufacturer Part Number WPY312959
The tumbler and motor belt in your dryer allows the drum to spin during the drying cycle. At 100 inches in length, this dryer drum belt is 3/8 of an inch wide and has five ridges. The belt is black in color and it is made entirely of rubber. If your dryer will not tumble, is noisy during operation, or will not start you may need to replace the belt. To complete this repair, you will need to remove the front panel as well as the drum. You will need a 5/16 nut driver and a stubby Phillips screwdriver to complete the repair. Be sure to disconnect power to the dryer before you begin this repair. During the repair, make sure the belt doesn't fall into the groove in the drum, which will cause it to be too loose. You should be able to access the belt and replace it by removing the front panel and bulkhead.
Fixes these symptoms
  • Marks left on clothes
  • No heat or not enough heat
  • Noisy
  • See more...
Installation Instructions
Raymond from West Bend, WI
electric dryer was rumbling - wheel or belt?
Unplugged dryer. Front came off easily. Removed front of blower. Wheel came off fairly easily - could then see that shaft of motor was circular with flattened side but inside of old wheel was rounded. New wheel popped right on. Took tumbler off so I could clean lint out more easily and get a good view of how the belt threaded through. Put the tumbler back on and reached back with both hands to thread it. Took a half dozen tries until I was sure it was seated correctly and not twisted. Put front... of dryer back on. So far (a week or so) the rumble is gone. Seems blower wheel was the cause of the rumble. Belt didn't seem worn but replaced anyhow. Read more...
Your Price
$21.20
  In Stock
Drive Belt
★★★★★
★★★★★
(45)
PartSelect Number PS11722115
Manufacturer Part Number 661570V
The Drive Belt is a 93 1/2" belt which wraps around the dryer drum to allow tension and movement. If broken the dryer will not turn properly, or there may be loud noises. The part is rated as "medium" difficulty to install. Refer to your model number and user manual to ensure this part is correct for you. To complete this repair you will need a Phillips screwdriver, 1/4 inch nut driver, a putty knife, and a pair of needle nose pliers. Ensure you disconnect your power to the dryer before beginning this repair, which should take between 30 and 60 minutes maximum to complete.
Fixes these symptoms
  • No heat or not enough heat
  • Noisy
  • Takes too long to dry
  • See more...
Installation Instructions
Lucas from Nuevo, CA
Need it a new pulley and belt
I did the repair all by my self and just payed for the parts. Read more...
Your Price
$11.92
  In Stock
Multi Rib Belt
★★★★★
★★★★★
(100)
PartSelect Number PS11742271
Manufacturer Part Number WP40111201
This dryer drum drive belt attaches to the motor pully and works the drum as the motor rotates. The belt has a length of 93- 3/6 inches, and wraps all the way around the dryer drum, around a tension pulley, and then around the drive motor pully. Replacing the rib belt could solve symptoms such as a screeching noise when the dryer tumbles, a broken belt (dryer will not tumble if its broken), no heat or not enough heat, or the dryer will not start. The tools needed for this repair are a nut driver and a putty knife. Remember to unplug the dryer before installing the part and protect your hands by wearing gloves.
Fixes these symptoms
  • No heat or not enough heat
  • Noisy
  • Takes too long to dry
  • See more...
Installation Instructions
Robert from Skokie, IL
Replace drive belt
Remove front panel, lint basket, motor mounts,exhaust hood, front drum brackets. Then slip serpentine belt around drum, pressure w/ tension idler pulley and slip around drive motor spindle. Replace all parts in reverse order (a two person job).
Vacuumed inside of dryer (full of lint.) Read more...
Your Price
$27.41
  In Stock
Multi Rib Belt - 91-5/8 Inches
★★★★★
★★★★★
(31)
PartSelect Number PS11741110
Manufacturer Part Number WP33002535
This multi rib belt spins the dryer drum during the drying cycle. This belt is 91-5/8 inches in length, 3/8th of an inch wide and has five ridges. It is black in color and made of rubber. You may need to replace the belt if your dryer is noisy or will not tumble.
Fixes these symptoms
  • Noisy
  • Takes too long to dry
  • Will Not Start
  • See more...
Installation Instructions
Mark from Lafayette, LA
Dryer squeeking loudly becoming worse quickly
I received my parts promptly and had no problems, they were accurate and fit well.

After removing the screws to the front door and panel I removed the wires to the door switch. Carefully I removed the belt and removed the drum. I took the time to vacuum all of the lent from the inside and and remove from all the wiring, motor and heating elements, etc. I replaced the drum rollers, belt, front glides and a buzzer that was on the blink. I reassembled the dryer and unforetunately the dryer was still squeeking. I later repeated the process and found that the tensioner wheel for the belt was the culprit. I cleaned then greased the bearing portion and replaced it. I reassembled the dryer a second time and now it's quiet as a mouse. By the way, you will need a rivet gun to replace the front glides and I recommend you give the belt tensioner wheel a good inspection the first time.

If your dryer is squeeking, go ahead and order the tensioner wheel also, it's a little money spent toward making sure you get rid of the noise! It might save you a lot of time and trouble. Read more...
Your Price
$56.44
  In Stock
Belt
★★★★★
★★★★★
(2)
PartSelect Number PS11750135
Manufacturer Part Number WPW10198086
Fixes these symptoms
Installation Instructions
Wayne from Woodbridge, VA
THE DRYER HAD A HUMMING NOISE THEN NOTHING KNOWING THE MOTOR HAD JUST BURNT OUT
PULLED THE DRYER APART TO GET TO THE MOTOR , REMOVED MOTOR , LOOKED FOR MODEL NUMBER OF DRYER AND DID RESEARCH ON WHERE TO BUY THE MOTOR AND BOUGHT FROM PARTS SELECT BECAUSE BOUGHT FROM THEM BEFORE Read more...
Your Price
$87.18
  In Stock
Dryer Drum Belt
★★★★★
★★★★★
(4)
PartSelect Number PS11748388
Manufacturer Part Number WPW10112954
This drum belt is for dryers. Drum belt attaches to the motor pulley and spins the drum as the motor rotates. Unplug the dryer before installing this part. Wear work gloves to protect your hand
Fixes these symptoms
Your Price
$60.71
  In Stock
Belt
★★★★★
★★★★★
(2)
PartSelect Number PS11748884
Manufacturer Part Number WPW10136934
Fixes these symptoms
Installation Instructions
GARY from CEDAR CITY, UT
metal rubbing sound at drum edge: found seal cut and idler bearing frozen
Getting the cabinet open is always fun. Prying the top open without breaking the clips. I took a small pry bar, covered the end with gray tape and found the the clips located on the front outer edges. You push in on the metal clips from the front and lift the top off the plastic alignment dowels. Remove the back, and two front panels. Removed the drum and vacuumed out everything (inspect). Remove old seal, idler pulley assembly from back of dryer (spring & bolt & note belt routing). Glue new felt seal on drum, slide on drive belt, bolt on new idler assembly & attach spring. Attach lower inner front panel screws. Flex out front panel and lower in the drum (make sure the felt seal lip is not folded over). Complete installing front panels. Slide belt towards center of drum (see old mark). Flex idler assembly and route drive belt. Hand spin drum to align belt. Plug in and run dryer briefly to confirm things run smoothly. Align lid clips and close. Unplug and attach back panel and vent hose. ALL DONE. Read more...
Your Price
$56.94
  In Stock
Blower Belt
★★★★★
★★★★★
(4)
PartSelect Number PS11746333
Manufacturer Part Number WP8544742
Fixes these symptoms
Installation Instructions
Tim from DUNCANVILLE, TX
1`) broken blower motor drive belt,2) blower moter drive belt pulley loosened & seperated from shaft
1) Unplugged unit & used the 5 in 1 tool to disengage top panel clips from top of front panel & tilted top panel up & out of the way, .
2) Disconnected electrical connection @ upper right of front panel, Used drill & 5/16" socket & adapter to remove 2 upper front panel screws on backside of panel & removed panel.
3) Removed 4 screws from lint screen duct, unplugged elect. con.@ the right & removed lint screen & duct from dryer bulkhead..
4) Loosened 2 top screws & removed 2 bottom screws from bulkhead & lifted bulkhead up & out & set aside.
5) Slid drum belt off the back of the drum & removed the drum
6) Ceaned the blower moter drive shaft threads & threads inside the shaft pulley. Used a file to clean up any burrs on shaft pulley, coated treads of pulley & shaft with red lock tite thread dressing & re-instaled pulley back onto shaft with ajustable pliers while holding blower fan blades steady from inside the blower motor housing. with other hand. note: (pulley is left handed thread)
7) Looped new belt onto drive motor pulley then worked it back onto blower moter pulley with one hand while turning the blades of the blower from inside the blower housing with other hand until it was back in place & ribs on belt were seated in the mating ribs of the pulley.
8) Put everything back in reverse order with the exception of removing the back panel to reinstall the drum belt onto the drive motor shaft pulley and tensioner @ bottom left in back of the dryer.

Hope this instructional is able to help some one else & good luck with your projects! Read more...

Related Parts

Back to Top