Maytag Dryer Wire Plugs and Connectors

Maytag Appliance Parts
Shop By Part Type

Popular Maytag Dryer Wire Plugs and Connectors

Your Price
$10.68
  In Stock
Heating Element Connection Wire Kit
★★★★★
★★★★★
3 Reviews
PartSelect Number PS334206
Manufacturer Part Number 279457
This kit is used for electric clothes dryers, and it comes with a yellow wire nut.
Fixes these symptoms
  • No heat or not enough heat
  • Takes too long to dry
  • See more...
Installation Instructions
Christopher from dublin, OH
no heat
took a couple differant parts to fix the dryer. i ordered one part at a time. i was expecting to wait the 5 days for shipping but i got home from work the next day of odering parts and they were there waiting for me on my doorstep. all three times i ordered. this website is the best site to order parts. i wont go to another website or store if i need to order parts for appliances. u guys have my business for life. thumbs up. Read more...
Your Price
$18.27
  In Stock
Terminal Block - Block Only
★★★★★
★★★★★
1 Review
PartSelect Number PS11741489
Manufacturer Part Number WP3397659
This part is an electrical connector where you can attach wires. This part does NOT included the wires, screws, and nuts. Must be order separately
Fixes these symptoms
  • No heat or not enough heat
  • Will Not Start
  • See more...
Installation Instructions
DAVID from LEESBURG, FL
One of the power cord connections on the terminal block was loose. Screw on terminal block was cross threaded when installed. Took six years to smoke the wire.
Removed and replaced terminal block, power cord and black wire to timer. Read more...
Your Price
$10.95
  In Stock
Terminal Block
★★★★★
★★★★★
2 Reviews
PartSelect Number PS11741048
Manufacturer Part Number WP33001244
This terminal block assembly does not come with any hardware. It it three inches long and made of plastic and metal.
Fixes these symptoms
  • No heat or not enough heat
  • Will Not Start
  • See more...
Your Price
$10.66
  In Stock
Wiring Harness
PartSelect Number PS11752344
Manufacturer Part Number WPW10298258
Your Price
$10.76
  In Stock
JUMPER WIR
PartSelect Number PS11757520
Manufacturer Part Number WPY304693
Fixes these symptoms
Installation Instructions
Jim from Bethlehem, PA
Maytag DE512 dryer would't heat.
After 22 years of continued use, my Maytag dryer stopped heating. Needless to say that I'm very impressed with the quality of Maytag products and I haven't had any problems with this unit until now. Your website was very informative and it really helped me pinpoint my problem. The parts were easy to install and it took less then 1 hour to complete. First: disconnect the power cord and the vent hose and lay the dryer on its back. There are two screws on the bottom of the door frame, remove these and then tilt the door assembly up until you can unlock the spring clips which hold the top of the door assembly to the dryer frame. Disconnect the two wires that are attached to the door switch and remove the door. The heater element is located on the right side, it's tube shaped. Remove the two slip-on connector wires attached to the top of the heater element. There are 4 tiny screws (use nut driver) holding the heater assy. First, remove two screws that hold the metal flap on the front of the element tube, then remove the screw located inside the element near the front lip (use a short nut driver) and then one screw attached to a flange at the back-end of the element on the right side. Pull out the heater assy, and install the replacement. If you're replacing the short jumper wire located on the element so be sure to replace it before you install the new element. Bolt the new element to the dryer using the 4 tiny screws, connect the 2 wires to the heater assy, re-attach the door by first aligning the spring clips to the top of dryer assy, then re-connect the 2 wires to the door switch, lower the door assy and install the 2 screws at the bottom of the door frame. Re-connect the vent hose and power. Read more...
Your Price
$23.57
  In Stock
Heating Element Terminal & Insulator Kit
★★★★★
★★★★★
1 Review
PartSelect Number PS1760665
Manufacturer Part Number Y304596
This kit comes with two ceramic insulators.
Fixes these symptoms
Your Price
$63.20
  In Stock
Terminal and Wire Kit
PartSelect Number PS334181
Manufacturer Part Number 279318
Fixes these symptoms
  • No heat or not enough heat
  • Will Not Start
  • See more...
Your Price
$74.45
  In Stock
Moisture Sensor Wire Harness
PartSelect Number PS11741707
Manufacturer Part Number WP3406653
Fixes these symptoms
  • No heat or not enough heat
  • Shuts off too soon
  • Takes too long to dry
  • See more...
Your Price
$10.68
  In Stock
Terminal Block
PartSelect Number PS11743293
Manufacturer Part Number WP61923
This part is connected to the rear bulkhead of the dryer with screws. It provides a way of connecting individual electrical wires and offers protection of the device from electrical surges (voltages and/or currents).
Fixes these symptoms
Installation Instructions
Henry from LA FOLLETTE, TN
Dryer not heating
Terminal Block was cracked and dryer was not receiving enough voltage, causing the heating element not to heat. Here were the steps I took to fix the problem:
1. Turn off breaker to dryer from 240v outlet
2. Unplug dryer from 240v wall outlet.
3. On outside, rear of dryer, remove cover plate and the clamp that the power cord goes through with nut driver or phillips screwdriver and take picture or write down how the power cord wires go to the terminal block.
4. Use nut driver or phillips screwdriver to remove the power cord wires from terminal block and ground wire from dryer body.
5. On top front of dryer, use large slotted screwdriver or some other tool to push in on the two clips in order to lift the cover up on dryer.
6. Take picture or write down how wires are attached to terminal block.
7. Remove wires from terminal block with nut driver or phillips screwdriver.
8. Use nut driver to remove terminal block from washer and install the new terminal block.
9. Reinstall wires to new terminal block.
10. Close dryer cover.
11. Reinstall clamp onto power cord wires and reinstall wires to new terminal block and ground wire to washer body then put cover plate back on.
12. Plug in dryer then turn on breaker.
13. Start dryer to see if it heats now.
Read more...
Your Price
$10.72
  In Stock
Dryer Belt Switch Jumper Wire
PartSelect Number PS11757524
Manufacturer Part Number WPY307173
This belt switch jumper wire is for dryers and takes the place of the belt switch in some models produced without the switch.
Fixes these symptoms

Related Parts