My Orders
KitchenAid Range Thermostats
GET YOUR OFFICIAL KitchenAid PARTS TO ENSURE VICTORY
Popular KitchenAid Range Thermostats
This part is used as a safety feature. If your range overheats this part will shut the range down.
This part is used as a safety feature. If your range overheats this part will shut the range down.
What this part fixes:
- Element will not heat
- Little to no heat when baking
- Little to no heat when broiling
Installation Instructions
Andrew from BOTHELL, WA
Oven would heat up very slowly and not reach more than 325 *F
I purchased all the likely suspects. It was a corroded lower heating element that was faulty. Fixed the burnt out light bulb for good measure while I was in there.
This thermostat is also known as a thermal cut-off fuse and is used in conjunction with your range. This part establishes and maintains the internal temperature of the oven cavity. When the temperature of your range gets too hot it will trip the high-limit thermostat safety, this will cut the power to the oven so that it does not continue to overheat. For this installation, you will need a Phillips screwdriver and a pair of needle-nose pliers. If your oven does not heat after a self-cleaning cycle you may need to replace the high-limit thermostat.
This thermostat is also known as a thermal cut-off fuse and is used in conjunction with your range. This part establishes and maintains the internal temperature of the oven cavity. When the temperature of your range gets too hot it will trip the high-limit thermostat safety, this will cut the power to the oven so that it does not continue to overheat. For this installation, you will need a Phillips screwdriver and a pair of needle-nose pliers. If your oven does not heat after a self-cleaning cycle you may need to replace the high-limit thermostat.
What this part fixes:
- Door won’t open after self cleaning cycle
- Element will not heat
- Little to no heat when baking
Installation Instructions
Joseph from Worthington, PA
Self Cleaning blows the thermostat fuse
Something Kitchen Aid wont tell you but running a self clean on this model stove blows the fuse located on the back of the stove.
First I slid the stove out and removed the back of the stove held in place by 8 Phillips screws. The thermostat fuse is located near the top middle on the back of the stove. Remove the 2 screws hold ... Read more ing it in place. Disconnect the wires, plug in the new part. Put it all back together. Job done in less than 30 minutes.
This repair would have cost $164 through A&E factory service.
First I slid the stove out and removed the back of the stove held in place by 8 Phillips screws. The thermostat fuse is located near the top middle on the back of the stove. Remove the 2 screws hold ... Read more ing it in place. Disconnect the wires, plug in the new part. Put it all back together. Job done in less than 30 minutes.
This repair would have cost $164 through A&E factory service.
Read less
An oven thermostat is a switch that opens and closes in response to the temperature it senses. It is typically found in the control panel, where a liquid-filled temperature-sensing bulb senses and maintains the internal oven temperature by cycling heat on and off. This safety thermostat trips when the controls are not working properly, or if the range gets too hot. If your oven will not start or is not heating properly, there could be an issue with the limit thermostat, and you should look to replace the part.
NOTE: Remember to disconnect the power from your range before you start this repair. This is an electrical appliance that can potentially hold a 220 volt charge.
An oven thermostat is a switch that opens and closes in response to the temperature it senses. It is typically found in the control panel, where a liquid-filled temperature-sensing bulb senses and maintains the internal oven temperature by cycling heat on and off. This safety thermostat trips when the controls are not working properly, or if the range gets too hot. If your oven will not start or is not heating properly, there could be an issue with the limit thermostat, and you should look to replace the part.
NOTE: Remember to disconnect the power from your range before you start this repair. This is an electrical appliance that can potentially hold a 220 volt charge.
What this part fixes:
- Door won’t open after self cleaning cycle
- Element will not heat
- Little to no heat when baking
Installation Instructions
Frederick from St. Louis, MO
No heat after cleaning oven
This built-in oven was slid out of it's space and set on a box. I removed the back cover with nut driver and located the safety overload device. removed nuts and used pliers to remove wires and replace them. The power must be off to do this repair.Replaced the cover and slid back into place. This could be a lot more difficult if your pow
... Read more
er cord or gas line is not long enough to make it out of your wall space. Or of your oven is attached well to the frame.
Read less
This high-limit thermostat is a safety-critical component designed to prevent overheating in ranges and wall ovens. It monitors internal temperatures and cuts power to the heating elements if the oven exceeds a preset threshold, typically around 335°F (170°C). Constructed from heat-resistant materials for long-term durability, it helps protect internal components and reduce the risk of fire or damage caused by control system failures, ventilation blockages, or fan malfunctions. A faulty thermostat may result in no heat, uneven cooking, or failure to start. Replacing this part restores safe and reliable oven operation. Installation should be performed with the appliance disconnected from power.
This high-limit thermostat is a safety-critical component designed to prevent overheating in ranges and wall ovens. It monitors internal temperatures and cuts power to the heating elements if the oven exceeds a preset threshold, typically around 335°F (170°C). Constructed from heat-resistant materials for long-term durability, it helps protect internal components and reduce the risk of fire or damage caused by control system failures, ventilation blockages, or fan malfunctions. A faulty thermostat may result in no heat, uneven cooking, or failure to start. Replacing this part restores safe and reliable oven operation. Installation should be performed with the appliance disconnected from power.
What this part fixes:
- Door won’t open after self cleaning cycle
- Element will not heat
- Will Not Start
Installation Instructions
William from Carbondale, CO
upper oven of wall oven would not heat suspected high temp limit switch
removed unit from cabinet tested switch it was OK checked wiring and found shorted out wire leading to switch. cut out bad section and spliced wire back together
problem solved
problem solved
This part will trip the controls if your appliance gets too hot or if it isn't working properly. It is a safety feature.
This part will trip the controls if your appliance gets too hot or if it isn't working properly. It is a safety feature.
Installation Instructions
Christy from Paso Robles, CA
After using the "self-clean" option, the panel blew out and the door remained locked. We knew we burnt fuses but didn't know which ones. We had a technician come out and tell us which ones. ($70.00) He quoted us a price of $495.00 for parts and labor. We did the repair ourselves and cost us $157
The hardest part was getting the oven out. The double oven is pretty heavy.
The screws were on the sides under a removable strip. Have a table about the same height as the base of the oven. It was easy to slide it straight over to the table.
The schematics are on top of the oven. Although you probably won't ... Read more need them for the parts we replaced. When you have the oven out and the back panel removed, it is easy to identify the exact parts you are replacing. The part numbers were the same on the fuses. The thermostat was a simple pull apart. Then undo the 2 screws inside the oven. The heat sensor required some figuring. There is a pin that holds it in place in a plastic casing. We used a small flat head screw driver to push the pin flat to loosen it from the casing. This part was behind the digital panel and the only one that didn't require the oven coming out.
We would easily do this project again and glad we did. We saved $340.00 by doing it ourselves. I am glad I found PartSelect.com
Make sure you turn off the breaker to the appliance first. You don't want any electrical surprises. The hospital bill would be more expensive than the repairman !!
The screws were on the sides under a removable strip. Have a table about the same height as the base of the oven. It was easy to slide it straight over to the table.
The schematics are on top of the oven. Although you probably won't ... Read more need them for the parts we replaced. When you have the oven out and the back panel removed, it is easy to identify the exact parts you are replacing. The part numbers were the same on the fuses. The thermostat was a simple pull apart. Then undo the 2 screws inside the oven. The heat sensor required some figuring. There is a pin that holds it in place in a plastic casing. We used a small flat head screw driver to push the pin flat to loosen it from the casing. This part was behind the digital panel and the only one that didn't require the oven coming out.
We would easily do this project again and glad we did. We saved $340.00 by doing it ourselves. I am glad I found PartSelect.com
Make sure you turn off the breaker to the appliance first. You don't want any electrical surprises. The hospital bill would be more expensive than the repairman !!
Read less
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
Replace this part if the oven stops working and the door locks while using the self-clean option on some appliances.
Replace this part if the oven stops working and the door locks while using the self-clean option on some appliances.
What this part fixes:
- Door won’t open after self cleaning cycle
- Little to no heat when baking
- Touchpad does not respond
Installation Instructions
Abdurehman from Lawrenceville, GA
When using self cleaning, oven door wouldn't open and screen panel went blank.
I searched similar problems on the web and learned that a whole lot of people have Kitchenaid stove with the same problem. They all stated that the thermostat burns when self cleaning. Since technician wanted $190.00, I decided to change it myself. The part cost me $40.00. To instal the thermostat, I removed the panel at the back of
... Read more
the stove and the thermostat is attached with two wires. After I replaced the thrmostat, the screen panel came on and I was able to open the door. I am posting this to tell people that anyone can do this.
Read less
L280-110F
L280-110F
Installation Instructions
curtis from Paris, IL
Oven would not shut down, kept heating
The front oven control panel was already in need of replacement. The digital readout had quit working sometime ago, so we began by replacing the control panel as well as the temperature probe. Neither of these items did the trick. Next I replaced the HI/Lo sensor switch. This replacement was a bit more labor intensive. Have to remove seve
... Read more
ral screws and remove a large portion of the top of the stove. Once access is gained to the hi/lo switch, it takes (2) minutes to replace it. This of course did not take care of the problem either. Finally I replaced the bake/broil/convection circuit board. This was a bit of a job, only because of the amount of wires to and from this board. I litterally took a picture of the board (from this web site) and drew in the wires and marked them by color and noted where they went. I then merely unplugged each wire and with one screw, removed the board and installed the new one. After plugging in the wires as per my picture, SUCCESS. The board did the trick. Over all, it was not bad doing the work myself. I know we saved a lot of money my doing it ourselves. Just gotta have patience.
Read less
This thermostat monitors temperature and regulates heating functions to maintain proper operating conditions. Designed for accuracy, it supports consistent performance and efficient operation.
This thermostat monitors temperature and regulates heating functions to maintain proper operating conditions. Designed for accuracy, it supports consistent performance and efficient operation.
This part establishes and maintains the internal temperature of the oven cavity.
This part establishes and maintains the internal temperature of the oven cavity.
