KitchenAid Range Valves

KitchenAid Appliance Parts
Shop By Part Type

Popular KitchenAid Range Valves

Your Price
$92.96
  In Stock
Surface Burner Valve - 16K - Left Front & Right Front
★★★★★
★★★★★
(15)
PartSelect Number PS11750353
Manufacturer Part Number WPW10206288
This is a surface burner valve for the left front and right front of your range. Burner valves are attached to the main gas line. When the switch is turned the gas then flows into a tube that mixes with air, creating the appropriate mixture for combustion. The valve monitors and controlsl the gas flow to the surface burner. It is roughly 3 inches long, 1.5 inches high, and about an inch wide. You should consider changing this part if your current one has seized and your range will not start.
Fixes these symptoms
Installation Instructions
Steve from Tracy, CA
Burner valve was seized
Lock the oven/stove controls by holding the START button for five seconds. This shuts off gas to the valve. Remove the knobs from the front of the stove using philips screwdriver. Undo the six screws that hold on the front bezel and remove to find the valve. Unscrew the top bracket using philps screwdriver. disconnect the valve using a wrench (I think it was 12mm). Compare the valve to the new one. Installation is reverse. Press the START button for five seconds to unlock the oven/stove. Test fire the burner. Cook a batch of chili. Read more...
Your Price
$120.75
  In Stock
Burner Valve - Left and Right Rear
★★★★★
★★★★★
(4)
PartSelect Number PS11750352
Manufacturer Part Number WPW10206287
Sold individually. This valve is for the right rear and left rear burners.
Fixes these symptoms
Installation Instructions
John from BEAUMONT, CA
Gas valve to grill burner locked closed.
1. Pulled range out from its cabinet setting and turned off the gas and unplugged the electric cord. 2. Removed all knobs (and soft pads) to burners. 3. Removed curved cover that covers the burners gas valves, gas manifold and igniter harness. 4. Removed a part that could be referred to as a flange or riser that is attached to the top of the range front at the burner level which the top of the curved piece is attached to. 5.The igniter attachments to the gas valves come off by pulling them away from the valve. I pulled away the one for the grill. 6. With these parts removed, eye sight and 1/2" open end wrench access is given to where the gas valve is attached to the burner gas line. 7. Disconnected the valve from the burner line. 8.Removed the bracket that holds the valve in place, thus removing the valve. 9. Installed new valve and bracket and attached valve to burner line. 10. Reattached the igniter part to the valve, then attached the flange (#4), then the curved cover, then the burner knobs (and soft pads). 11.Reconnected the electric cord and opened the gas valve. 12 Pushed the range back into its cabinet place and pushed the 'Cancel:' mark as directed by the digital read-out on the range's back riser control panel. Checked for gas leak. None. It took a bit of scrutiny to see what to remove and in what sequence. Read more...
Your Price
$48.50
  In Stock
LP Conversion Kit
★★★★★
★★★★★
(3)
PartSelect Number PS11749494
Manufacturer Part Number WPW10170516
Installation Instructions
Andy from LOYALTON, CA
Natural Gas to Liquid Petrolium Conversion
The LP Conversion kit for the 5 surface burners that was supplied with the range are wrong. The oven and broiler orifice jets that came with the range were correct. Order the 5 surface jets to complete your LP conversion. Read more...
Your Price
$34.40
  In Stock
Burner Cap - Small
★★★★★
★★★★★
(2)
PartSelect Number PS11740923
Manufacturer Part Number WP3191898
Sold individually.
Installation Instructions
Joseph from Matawan, NJ
needed to replace the main top of stove
First I removes all visible screws. The stove top would not budge. I noticed that the elements had screws holding the top in place. These were difficult to remove and all eight screw broke. I then removed the top. I had to remove the broken screws by drilling them out and re-tapping the threads. This was the single most difficult thing to do and took the most time. Once this was complete, re-installing the top was quite simple.
Haviong directions would have been very helpful.
Read more...
Your Price
$49.12
  In Stock
Gas Orifice (Spud)
PartSelect Number PS11753337
Manufacturer Part Number WPW10347414
Your Price
$46.75
  In Stock
Burner Head - 16K
★★★★★
★★★★★
(4)
PartSelect Number PS11754347
Manufacturer Part Number WPW10406878
This part distributes flame evenly to your cookware.
Installation Instructions
Charles from ATLANTA, GA
REPLACING burner head and ignitor
Remove the screw on the front of each side, also there are two screws holding the burner controls. Remove the burner knobs. There are two screws holding the burner head to the top of the burner panel, looking down on the burner head, these will not come out easily. Here's where the drill comes in. Drill the two screws head off, there are two gas line connections that must be removed, be careful not to twist the gas line. Remove the burner head and replace with the new one. When replacing the burner head, screw the gas line to the burner head first, then to the main gas control. Read more...
Your Price
$49.39
  In Stock
LP Orifice
PartSelect Number PS12070661
Manufacturer Part Number W11087486
This LP orifice is for the bake and broil, 17K & 11K. The LP orifice helps control the gas that comes out of the burner tubes.
Installation Instructions
Andy from LOYALTON, CA
Natural Gas to Liquid Petrolium Conversion
The LP Conversion kit for the 5 surface burners that was supplied with the range are wrong. The oven and broiler orifice jets that came with the range were correct. Order the 5 surface jets to complete your LP conversion. Read more...
Your Price
$28.65
  In Stock
Burner Head - 6K
PartSelect Number PS11754341
Manufacturer Part Number WPW10406243
This is the Right Rear Burner Head.
Installation Instructions
Charles from ATLANTA, GA
REPLACING burner head and ignitor
Remove the screw on the front of each side, also there are two screws holding the burner controls. Remove the burner knobs. There are two screws holding the burner head to the top of the burner panel, looking down on the burner head, these will not come out easily. Here's where the drill comes in. Drill the two screws head off, there are two gas line connections that must be removed, be careful not to twist the gas line. Remove the burner head and replace with the new one. When replacing the burner head, screw the gas line to the burner head first, then to the main gas control. Read more...
Your Price
$82.54
  In Stock
Burner Cap Kit - Black
PartSelect Number PS11749758
Manufacturer Part Number WPW10183374
This kit includes all 5 burner caps.
Your Price
$34.71
  On Order
Burner Cap
★★★★★
★★★★★
(2)
PartSelect Number PS11745641
Manufacturer Part Number WP8284669
Burner Cap - 6000 BTU Sold individually.

Related Parts