KitchenAid Range Hardware
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular KitchenAid Range Hardware
Your Price
$6.25
In Stock
KitchenAid Range Torx Screw
This was made more difficult by the fact that the screws that hold the burners to the range top were rusted and had to be drilled out so the the burners could be released from the top.
1. Disconnect the power to the range.
2. Open the top oven door.
3. Remove 2 - 1/4" sheet metal screws at the front corners of the range top assy. Remove the Burner knobs and the two Phillps screws that holds the gas valve assembly to the range top.
4. With a drill, remove the tops of the screws to release the burners from the range top. If the screws are in good condition and just unscrew them and the upper burners from the Orifice Holders. (I had to replace the orifice holders because the screws were stuck in them due to rust).
5. When the burners are free, lift the range top at the front and remove it from the range. Disconnect the ignitor wires from the ignitors on each holder.
6. To replace the Orifice Holders, disconnect the gas supply pipes from each holder by loosening the compression nut at the holder using an adjustable wrench. Secure the Orifice Holders when loosening the fittings, BE CAREFUL not to damage the aluminum gas supply pipes.
7. Note that there are 3 different Holders, be sure to use the holder that matches the specific location.
8. For LP gas fueled ranges ONLY, remove the small gas jets from the old holders and install them in place of the parts supplied with the new orifice holders. The new parts contain NATURAL GAS jets which are not compatible with LP gas. Each Different Orifice Holder uses a specific orifice or jet, make certain that the orifice matches the orifice holder. Check for leaks at the gas connections using soapy water.
9. Carefully raise the old ignitor switches (4) off the shafts of the gas valves. Note the top and bottom configuration of the switches
10. Carefully release the wires that come from the rear of the range from the rearmost switch. Press a suitable pin or other suitable tool in a the hole, beside the wire, just enough to release the wire. (Look at the NEW switch assemble to see how this works). Remove the wires from the NEW switch first to see how it is done. Repeat the process on the old switches. (you will re-use the wires that come up from the rear of the range.
11. Install the new switch assembly over the four (4) burner gas valves, take care to align the "D" shaped shafts with the holes in each valve.
12. Insert the wires in the two connections on the rearmost switch. CAUTION!!! Be sure to install the wires so that the color codes agree with the wires on the new switch assembly. Black to black and gray to gray.
13. Install the 4 clear plastic "shields" over the shafts and against the top of each switch.
14. Re-connect the ignitor wires to the burners and Re-Install the range top, in the reverse order of dis-assembly. Read more...
PartSelect Number PS11741257
Manufacturer Part Number WP3368921
7-18 x 3/4-Inch - sold individually.
Fixes these symptoms
- Gas igniter glows, but will not light
- Will Not Start
- See more...
Installation Instructions
Michael from Dardanelle, AR
Ignitor switches shorted out
The ignitor switches are installed on top of the 4 gas valves for the range top. These switches control the electronic ignition. To replace the switch assembly the top of the range must be removed to gain access. This was made more difficult by the fact that the screws that hold the burners to the range top were rusted and had to be drilled out so the the burners could be released from the top.
1. Disconnect the power to the range.
2. Open the top oven door.
3. Remove 2 - 1/4" sheet metal screws at the front corners of the range top assy. Remove the Burner knobs and the two Phillps screws that holds the gas valve assembly to the range top.
4. With a drill, remove the tops of the screws to release the burners from the range top. If the screws are in good condition and just unscrew them and the upper burners from the Orifice Holders. (I had to replace the orifice holders because the screws were stuck in them due to rust).
5. When the burners are free, lift the range top at the front and remove it from the range. Disconnect the ignitor wires from the ignitors on each holder.
6. To replace the Orifice Holders, disconnect the gas supply pipes from each holder by loosening the compression nut at the holder using an adjustable wrench. Secure the Orifice Holders when loosening the fittings, BE CAREFUL not to damage the aluminum gas supply pipes.
7. Note that there are 3 different Holders, be sure to use the holder that matches the specific location.
8. For LP gas fueled ranges ONLY, remove the small gas jets from the old holders and install them in place of the parts supplied with the new orifice holders. The new parts contain NATURAL GAS jets which are not compatible with LP gas. Each Different Orifice Holder uses a specific orifice or jet, make certain that the orifice matches the orifice holder. Check for leaks at the gas connections using soapy water.
9. Carefully raise the old ignitor switches (4) off the shafts of the gas valves. Note the top and bottom configuration of the switches
10. Carefully release the wires that come from the rear of the range from the rearmost switch. Press a suitable pin or other suitable tool in a the hole, beside the wire, just enough to release the wire. (Look at the NEW switch assemble to see how this works). Remove the wires from the NEW switch first to see how it is done. Repeat the process on the old switches. (you will re-use the wires that come up from the rear of the range.
11. Install the new switch assembly over the four (4) burner gas valves, take care to align the "D" shaped shafts with the holes in each valve.
12. Insert the wires in the two connections on the rearmost switch. CAUTION!!! Be sure to install the wires so that the color codes agree with the wires on the new switch assembly. Black to black and gray to gray.
13. Install the 4 clear plastic "shields" over the shafts and against the top of each switch.
14. Re-connect the ignitor wires to the burners and Re-Install the range top, in the reverse order of dis-assembly. Read more...
Your Price
$7.30
In Stock
KitchenAid Range Screw - 10-16 X 1
PartSelect Number PS11741409
Manufacturer Part Number WP3387230
This screw is sold individually.
Installation Instructions
Wendy from BRAINTREE, MA
Freezer handle came loose on one side
Discovered that the seating in the handle was stripped on one side so removed the old handle (toughest part of the repair). Based on a previously asked/answered question, the PartSelect website provided an accurate list of the required parts (and corresponding part numbers) so I had everything I needed. Installing the new handle was very straightforward and quick.
Read more...
Your Price
$7.30
In Stock
KitchenAid Range Screw
PartSelect Number PS11750186
Manufacturer Part Number WPW10200660
Discover the unmatched excellence of the Whirlpool Screw for stoves, ovens, and ranges. This impressive Screw, 10-16 x 3/4 size, is a genuine OEM part compatible with various models from Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef. While distinct in size and shape, rest assured this part fits seamlessly into your appliance. Thriving on quality and optimum performance, it is always recommended to confirm the adequacy of the part number for your model before ordering. The installation of this screw should always be carried out following the right safety practices. Get your appliance up and running with the proven reliability of Whirlpool parts.
Fixes these symptoms
- Door won’t close
- See more...
Your Price
$7.30
In Stock
KitchenAid Range Igniter Screw
- Removed te two Torx screws.
- Pulled the burner a couple of inches to be able to disconnect the wire.
- Spent a lot of time removing the small Philips screw holding the ignitor. Ended up breaking the ignitor with pliers to be able to put WD40 under the screw's head.
- Treated all screws with a high temperature copper paste to prevent oxidation.
Installed the new ignitor with the new screw.
- Reconnected the wire.
- Installed the two Torx screws.
- Voila, it works. Read more...
PartSelect Number PS11745563
Manufacturer Part Number WP8273062
This screw is sold individually.
Fixes these symptoms
- Gas igniter glows, but will not light
- Will Not Start
- See more...
Installation Instructions
Didier from LONE TREE, CO
Ignitor did not work
- Removed the cover.- Removed te two Torx screws.
- Pulled the burner a couple of inches to be able to disconnect the wire.
- Spent a lot of time removing the small Philips screw holding the ignitor. Ended up breaking the ignitor with pliers to be able to put WD40 under the screw's head.
- Treated all screws with a high temperature copper paste to prevent oxidation.
Installed the new ignitor with the new screw.
- Reconnected the wire.
- Installed the two Torx screws.
- Voila, it works. Read more...
Your Price
$20.95
In Stock
KitchenAid Range Washer Screw
PartSelect Number PS12741703
Manufacturer Part Number W11404293
Sold individually.
Fixes these symptoms
- Lid or door won’t close
- See more...
Installation Instructions
Ed from NEW BERN, NC
Replace hinge and hinge spring assembly.
I mounted the left and right hinge assemblys into the washer (spring assembly) and then mounted the glass top on to the hinge assemblies. Inserted the screws and tightened as required.
Read more...
Your Price
$7.30
In Stock
KitchenAid Range Dryer Screw
PartSelect Number PS11746840
Manufacturer Part Number WP90767
This screw is sold individually.
Installation Instructions
Alexander from Lakeland, FL
Broken Dryer Knob
First let me just say that Partselect.com is now one my stored favorites in my web browser. I came home from a business trip and saw a pair of pliers on the dryer. I thought that was odd until my wife informed me that the knob on the dryer had broken. So she was using the pliers to select the cycle. Somehow she knew where the missing pointer was actually pointing. Since the dryer was over 5 years old I saw this as an opportunity to upgrade both appliances. Not with my frugal wife. A search of the Internet popped up partselect. I ordered Wednesday morning and the parts where on my doorstep late Thursday. Trust me I was very surprised. Everything worked perfectly. Two thumbs up!!!
Read more...
Your Price
$7.30
In Stock
KitchenAid Range Dryer Support Roller Clip
PartSelect Number PS11746832
Manufacturer Part Number WP90296
Sold Individually.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
randy from simi valley, CA
bad drum rooller bearing
took the top, sides and back removed the drum and replaced the roller roller shaft and drive belt and the belt tensioner
Read more...
Your Price
$23.05
In Stock
KitchenAid Range Leveler Foot Screw (nylon)
PartSelect Number PS16875974
Manufacturer Part Number W11665456
This is a leveling leg for your oven, range, or stove. The leveling legs on your oven allow your appliance to sit perfectly flat. The new one may be longer in length than your original, but will work the same. Install the new leveling leg, and test if you have it adjusted properly by putting the appliance on four legs. Adjust in or out as required if your oven is rocking. It is recommended to check the other three leveling legs on your appliance in case they are also damaged or worn. The leveling leg measures 1.859", is all black in color, and is made entirely out of plastic. This leg may be shorter than the original but is the factory replacement. Longer leg is not available.
Installation Instructions
Eric from Goldens Bridge, NY
cracked glass top and broke leveling leg in moving the stove
Directed my wife because I have shoulder injury. She did all the work.
Read more...
Your Price
$7.30
In Stock
KitchenAid Range Air Conditioner Cover Screw
In this spirit of any repair, I replaced them, and it was not the issue. I don't know what I expected.
Ceiling. YouTube. Pacing.
Then I figured it was this part - the motor coupling. I unplugged the machine and took out the drain tube. I leaned the machine back and propped it up with an empty detergent bottle, because those were abundant. Ratchet off a few bolts and the motor comes out. The coupling was indeed broken. The new one slips right in - I tapped it a few times with a mallet for good measure / vengeance. Ratcheted the bolts back on and tipped it back up.
Pros: Washer works now.
Cons: Everest-esque laundry pile to address.
But hey, it worked! I am no handyman and it wasn't too bad at all. Half hour tops. Read more...
PartSelect Number PS11740701
Manufacturer Part Number WP308685
Sold individually.
Installation Instructions
Peter from WRENTHAM, MA
Kenmore 80 Series Washer - Agitator Stopped Working
First I screamed at the ceiling, because I have a three year old and an infant, and the washing machine was dead. Then I went to youtube. It seemed like the "agitator dogs" were the issue. In this spirit of any repair, I replaced them, and it was not the issue. I don't know what I expected.
Ceiling. YouTube. Pacing.
Then I figured it was this part - the motor coupling. I unplugged the machine and took out the drain tube. I leaned the machine back and propped it up with an empty detergent bottle, because those were abundant. Ratchet off a few bolts and the motor comes out. The coupling was indeed broken. The new one slips right in - I tapped it a few times with a mallet for good measure / vengeance. Ratcheted the bolts back on and tipped it back up.
Pros: Washer works now.
Cons: Everest-esque laundry pile to address.
But hey, it worked! I am no handyman and it wasn't too bad at all. Half hour tops. Read more...
Your Price
$7.30
In Stock
KitchenAid Range Screw
PartSelect Number PS11741605
Manufacturer Part Number WP3400832
This screw is sold individually.
Installation Instructions
Alan from PEARISBURG, VA
Broken front glass
Very easy. Take the two top screws out and the two bottom holders off. The bottom holders hold the glass up in place. Grab the handle and pull glass out. To install put handles screws back on the glass and slide in place. Once in place install the bottom holders pieces back on. *** I would buy screws because after years of use the head rust out and sometimes they are hard to get off... all in all very easy to install
Read more...
Related KitchenAid Range Parts
- All KitchenAid Range parts
- KitchenAid Range Brackets and Flanges
- KitchenAid Range Caps and Lids
- KitchenAid Range Circuit Boards and Touch Pads
- KitchenAid Range Cooktops
- KitchenAid Range Doors
- KitchenAid Range Drawers and Glides
- KitchenAid Range Ducts and Vents
- KitchenAid Range Elements and Burners
- KitchenAid Range Fans and Blowers
- KitchenAid Range Fuses
- KitchenAid Range Grates
- KitchenAid Range Handles
- KitchenAid Range Hinges
- KitchenAid Range Hoses and Tubes
- KitchenAid Range Igniters
- KitchenAid Range Ignitions
- KitchenAid Range Insulations
- KitchenAid Range Knobs
- KitchenAid Range Latches
- KitchenAid Range Legs and Feet
- KitchenAid Range Lights and Bulbs
- KitchenAid Range Manuals and Literatures
- KitchenAid Range Motors
- KitchenAid Range Panels
- KitchenAid Range Power Cords
- KitchenAid Range Racks
- KitchenAid Range Seals and Gaskets
- KitchenAid Range Sensors
- KitchenAid Range Switches
- KitchenAid Range Thermostats
- KitchenAid Range Trims
- KitchenAid Range Valves
- KitchenAid Range Wire Plugs and Connectors