My Orders
Jenn-Air Range Hinges
GET YOUR OFFICIAL Jenn-Air PARTS TO ENSURE VICTORY
Popular Jenn-Air Range Hinges
The hinges control the rate that the oven door opens and closes, and allows the door to stay open at an angle. This hinge can be used on either the left or right hand side of your oven, and is approximately 20 1/2 inches long. If your oven door will not open or close easily, you may need to replace this part. It may be a good idea to replace both hinges at the same time. If a spring has become loose on one hinge, the other hinge is likely to have the same issue. The repair is simple and only requires a Phillips screwdriver and a small bent nail. For a full step-by-step guide, check out the video below.
The hinges control the rate that the oven door opens and closes, and allows the door to stay open at an angle. This hinge can be used on either the left or right hand side of your oven, and is approximately 20 1/2 inches long. If your oven door will not open or close easily, you may need to replace this part. It may be a good idea to replace both hinges at the same time. If a spring has become loose on one hinge, the other hinge is likely to have the same issue. The repair is simple and only requires a Phillips screwdriver and a small bent nail. For a full step-by-step guide, check out the video below.
Installation Instructions
William from Statesville, NC
Oven door wouldn't close completely
Parts arrived in three days and it was an easy swap of the hinges but the same problem still existed: the oven door wouldn't close completely, so the oven light stayed on and the convection wouldn't work either unless the door closed all the way. The replacement hinge's springs apparently aren't strong enough to close it and the springs a
... Read more
ren't adjustable - which is a design flaw. I did correct the problem though, by using three dollars worth of 1" round magnets, which I placed inside the door: they stay put and are strong enough to pull the door tight.
Read less
This door hinge can be used for the left or right side. As per the manufacturer if the hinges have never been replaced on the appliance, they suggest to replace the door hinge receptacle kit.
This door hinge can be used for the left or right side. As per the manufacturer if the hinges have never been replaced on the appliance, they suggest to replace the door hinge receptacle kit.
Installation Instructions
Norman from Brockton, MA
I leaned on the door and broke the hindge
I had a lot of trouble unlocking the door hindge you must pull the door out to change the hinge they are on the hinge and slide foward then pull the door up and out lay the door flat on a table cover the table with a towel so you don't scrach either one. Unscrew 6 screws on the door cover. 3 on top 3 on bottom take the cover off the hinge
... Read more
s are exposed there 3 screws on the hinge 1 on the front and 2 on the bottom replace hinges install face insert door and lock the hinge it's all done. I wish I had these directions
Read less
Need to reorganize your fridge? Look no further! The GE Shelf Support End Cap is made just for the right side of your refrigerator shelf. It?s a key piece when it comes to keeping things where they should be ? it holds the door shelf in place, keeping your fridge tidy and making the most out of your space. Think of it as a tiny bit of support for your hardworking fridge. It?s a genuine GE part, which means it?s been designed and built especially for your appliance. So you can be confident it?ll fit your fridge perfectly and work like a dream. Don't compromise on a part like this - it plays a big role in the daily function of your fridge. With the GE Shelf Support End Cap, you know you're getting reliable quality that?s guaranteed. Trust us when we say this is the piece you need to get your refrigerator back to working like the day you bought it.
Need to reorganize your fridge? Look no further! The GE Shelf Support End Cap is made just for the right side of your refrigerator shelf. It?s a key piece when it comes to keeping things where they should be ? it holds the door shelf in place, keeping your fridge tidy and making the most out of your space. Think of it as a tiny bit of support for your hardworking fridge. It?s a genuine GE part, which means it?s been designed and built especially for your appliance. So you can be confident it?ll fit your fridge perfectly and work like a dream. Don't compromise on a part like this - it plays a big role in the daily function of your fridge. With the GE Shelf Support End Cap, you know you're getting reliable quality that?s guaranteed. Trust us when we say this is the piece you need to get your refrigerator back to working like the day you bought it.
Installation Instructions
Barrett from MERCER ISLAND, WA
The oven door didn't shut all the way
Clearly, the oven gasket was not the cause of the problem.
The hinge replacements did not fix the problem. I think the problem was that the hinge's mating part inside the door had been deformed, perhaps by leaning on the door when fully opened. I compensated for that by placing two stacked magnets near the upper hinge mounting scre ... Read more w hole on the inside of the oven body. (0.75" screws , 8-24 or metric equiv., needed for the upper screw location.) This gave the hinge about 15 degrees of additional door tilting force. In addition, I added 6 ceramic magnets across the top of the door mating surface, kudos to that website. Now it pulls fully flush with the magnets.
Ceramic magnets are good to 400+ degrees and they come in boxes of 120 for $12.00.
I only had one oven as a sample, but I could see what I thought was deformation on the inside of the oven door where the hinges are inserted. In this case, I think that makes (only) hinge replacement futile.
Sorry if this solution does not fit your marketing desire, but I did leave the new hinges installed.
The hinge replacements did not fix the problem. I think the problem was that the hinge's mating part inside the door had been deformed, perhaps by leaning on the door when fully opened. I compensated for that by placing two stacked magnets near the upper hinge mounting scre ... Read more w hole on the inside of the oven body. (0.75" screws , 8-24 or metric equiv., needed for the upper screw location.) This gave the hinge about 15 degrees of additional door tilting force. In addition, I added 6 ceramic magnets across the top of the door mating surface, kudos to that website. Now it pulls fully flush with the magnets.
Ceramic magnets are good to 400+ degrees and they come in boxes of 120 for $12.00.
I only had one oven as a sample, but I could see what I thought was deformation on the inside of the oven door where the hinges are inserted. In this case, I think that makes (only) hinge replacement futile.
Sorry if this solution does not fit your marketing desire, but I did leave the new hinges installed.
Read less
Sold individually.
Sold individually.
Installation Instructions
Patrick from MORAGA, CA
Two digits on the touch pad didn't work "9" & "0". Went to utube and they said hinges go bad causing heat to leak affecting touch pad
Pull range out 6 inches. Open door to 45 degrees and pull up to remove door. Remove both side plates, two screws each side. Remove both hinges by loosening two small bolts on the front of range that connect to the hinges. Place new hinges in place. Bolt hinges using bolts you removed, replace side panels. Slide door on hinges and push ba
... Read more
ck range.
Read less
This hinge can be used for either the left or the right side of the oven door. Sold individually.
This hinge can be used for either the left or the right side of the oven door. Sold individually.
Installation Instructions
Lar from Cary, NC
Oven Door hinge broke
0. Throw oven circuit breaker 1. Open oven door and slide/lift door off of hinge posts 2. Remove oven drawer 3. Slide oven out from between cabinets and turn so that the back is accessible. 4. remove Phillips screws holding the cover-rear and side panel to the stove. Note which screws have pan heads and which are hex head. 5. remove stov
... Read more
e elements and pans 6. Raise stove Top Assembly and release ceramic element sockets from their clips. 7. Push the supports for the Top Assembly fornt and back to release them from their sockets so that the Top Assembly can be lifted to near vertical. 8. Remove the hex head screw holding the Control Panel End Cap to the side panel. (Steps 5-7 might be avoided if you have a small socket wrench that can get to this screw without removing the elements.) 9. Remove the other screws holding the top of the side panel to the "Box Burner" pan that sits under the Top Assembly. 10. Pull side panel slightly away from the oven and lift it to disconnect it from the posts that hold the side panel to the front of the oven. 11. Remove the two screws on the front of the oven that hold the hing mechanism. 12. tilt and remove the hinge. 13. Open the replacement hinge so that it can fit through the hinge opening in the front of the oven. 14. Reassemble.
Read less
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
This door hinge assembly is made entirely of metal. It is used on either the left or right hand side of the oven door.
This door hinge assembly is made entirely of metal. It is used on either the left or right hand side of the oven door.
Installation Instructions
James from Morgantown, PA
oven door difficult to open and shut
Initially installed two oven hinges. To remove door: fully open oven door and insert a small nail (wire or metal paper clip will work) into the hole on the moveable arm on each hinge. (This pin will prevent the hinge from snapping shut when you remove the door.) Next you remove one screw from the small cover plate where the hinge enters
... Read more
the body of the stove. After removal, close the door to broiling position (about two or three inches open). Now lift the entire door up and then out away from the stove (this action will lift the hinges up and off of the pins on the hinge receptacle and allow you to remove the entire door). Remove the several screws that attach the door "skin" to expose the hinges. Remove two screws from one end of each hinge and disengage the retaining arms from the slots on the other end to remove each hinge. Installation is the reverse. I decided to disassemble the oven door glass and clean all sides. This took a lot longer than the hinge replacement but looks new again. Your new hinges will have cute little pins that you will need to remove before it will close (install door and open completely to install cover plates and then remove pins) FYI, I didn't know about this Parts Select site so I had purchased the hinges without installing the hinge receptacles (the small metal case with the pins that attaches the door to the stove). My site didn't have the hinge receptacles and it didn't appear that they could be defective. BIG MISTAKE! The door did not close completely......it was easy to open and close but it was not sealing properly. After researching on the internet I found that new hinges require new/redesigned receptacles as the pins are slightly different. So after installing the receptacles (remove door to access four small 1/4 metal screws) on the stove sides (our built-in stove doesn't have sides so acess was easy). The door closed properly.
Read less
Each hinge is sold seperately.
Each hinge is sold seperately.
Installation Instructions
James from Elmont, NY
broken door hinge
unplug unit remove rear panel screws lift up stove top remove top two screws remove panel remove two hinge screws remove replace hinge and follow in reverse order
This range oven door hinge is designed to restore smooth, secure door operation by properly supporting and controlling the movement of the oven door. Intended for the left-hand side, it helps ensure the door opens and closes evenly, seals correctly, and stays in position during use. It is commonly used to fix issues such as stiff movement, shaking, or doors that do not close properly.
This range oven door hinge is designed to restore smooth, secure door operation by properly supporting and controlling the movement of the oven door. Intended for the left-hand side, it helps ensure the door opens and closes evenly, seals correctly, and stays in position during use. It is commonly used to fix issues such as stiff movement, shaking, or doors that do not close properly.
