My Orders
Jenn-Air Range Switches
GET YOUR OFFICIAL Jenn-Air PARTS TO ENSURE VICTORY
Popular Jenn-Air Range Switches
This surface burner switch is a genuine replacement component designed to regulate the heat output of the left front burner on select electric ranges. It functions by cycling electrical power to the burner, maintaining the desired temperature throughout cooking. A faulty switch may result in overheating, lack of heat, or the burner remaining at a single temperature setting. Replacing this part restores precise temperature control and ensures safe, consistent operation. Installation should be performed with the appliance disconnected from power, and may require basic tools and reference to model-specific instructions.
This surface burner switch is a genuine replacement component designed to regulate the heat output of the left front burner on select electric ranges. It functions by cycling electrical power to the burner, maintaining the desired temperature throughout cooking. A faulty switch may result in overheating, lack of heat, or the burner remaining at a single temperature setting. Replacing this part restores precise temperature control and ensures safe, consistent operation. Installation should be performed with the appliance disconnected from power, and may require basic tools and reference to model-specific instructions.
Installation Instructions
Shannon from Orlando, FL
Front 3 setting burner was not heating properly; switched to high without adjustment
Looked up the part in the online manual, watched a YouTube video, removed upper back of range, swapped out part. Saved $200!!
This infinite switch is for 8-inch range burners. When an element is unable to produce any heat on a modern oven, the problem may lie with the infinite switch. This switch is responsible for sending power to the surface elements. Check the element and terminal block to ensure they are working properly. If they are in working order, check the infinite switch at the control panel for any wires that have overheated, or broken terminals to or from the infinite switch. If the infinite switch is damaged or malfunctioning, it will need to be replaced. Remember to unplug your range before beginning this repair.
This infinite switch is for 8-inch range burners. When an element is unable to produce any heat on a modern oven, the problem may lie with the infinite switch. This switch is responsible for sending power to the surface elements. Check the element and terminal block to ensure they are working properly. If they are in working order, check the infinite switch at the control panel for any wires that have overheated, or broken terminals to or from the infinite switch. If the infinite switch is damaged or malfunctioning, it will need to be replaced. Remember to unplug your range before beginning this repair.
Installation Instructions
JACK from FRANKLINVILLE, NJ
Burner switch would not regulate heat
Turn off breaker in electric panel fore stove. Put screw driver into slots in front of glass top surface. Pry top up carefully until top pops up.Remove burner dial, remove two philips head screws holding switch. Lift top carefully and prop up.With new switch close remove wires from old switch one at a time and place on new switch. Place n
... Read more
ew switch back in place, securing with philips screws. Remove prop and carefully press top down until it snappes into place.Replace dial, turn breaker back on and try burner.
Read less
This dual surface element control switch is a genuine OEM replacement part designed to fit select models of stoves, ovens, and ranges. The control switch is an essential component that allows you to turn the surface element on and off, as well as regulate the amount of heat the element produces. If your stove’s surface element isn’t heating properly, fluctuates in temperature, or won’t turn off, replacing the control switch can restore full functionality. Before installation, ensure the range is unplugged, or disconnect the power at the house circuit breaker to avoid electrical hazards. The surface element control switch is usually located behind the stove’s front control panel. To install, remove the panel and disconnect the old switch from the wiring harness. Install the new switch by securing it in place and reconnecting the wiring to match the original configuration. After installation, turn the power back on and test the surface element to verify it operates correctly.
This dual surface element control switch is a genuine OEM replacement part designed to fit select models of stoves, ovens, and ranges. The control switch is an essential component that allows you to turn the surface element on and off, as well as regulate the amount of heat the element produces. If your stove’s surface element isn’t heating properly, fluctuates in temperature, or won’t turn off, replacing the control switch can restore full functionality. Before installation, ensure the range is unplugged, or disconnect the power at the house circuit breaker to avoid electrical hazards. The surface element control switch is usually located behind the stove’s front control panel. To install, remove the panel and disconnect the old switch from the wiring harness. Install the new switch by securing it in place and reconnecting the wiring to match the original configuration. After installation, turn the power back on and test the surface element to verify it operates correctly.
Installation Instructions
Vanessa from Castleberry, AL
The right front dual burner went to high no matter the setting
I located the model number. Then searched the problem on YouTube. I saw that it was most likely the infinite switch and was an easy fix, so I ordered the part from this site and replaced it following the directions on the video. It's now as good as new!
This surface burner switch, also known as an infinite switch, controls and regulates the heat output of the burners on a stovetop. The user simply adjusts the knob on the user interface panel, which in turn controls this switch. Made for various ranges, wall ovens and cooktops, this is a genuine OEM part that comes by itself, without any hardware like screws or nuts. This burner switch is an electrical component that you also handle directly, so it can become faulty leading to problems like your stovetop not heating enough, overheating or staying at a fixed heat. This burner switch is a vital component for your stovetop and if it presents any of those issues, it needs to be replaced immediately. A screwdriver, set of pliers and wiring diagram will be needed for the replacement and installation process, and you will need to remove your appliance from the wall outlet first. Remove the knobs from the control panel and then gain access to the underneath portion of it with your screwdriver and disconnect the switch. Remove the wires from the burner switch with a set of pliers and disconnect the securing screws holding the switch in place. Now, you can install the new switch and reassemble the panel, being mindful of wiring each connector to the appropriate wire.
This surface burner switch, also known as an infinite switch, controls and regulates the heat output of the burners on a stovetop. The user simply adjusts the knob on the user interface panel, which in turn controls this switch. Made for various ranges, wall ovens and cooktops, this is a genuine OEM part that comes by itself, without any hardware like screws or nuts. This burner switch is an electrical component that you also handle directly, so it can become faulty leading to problems like your stovetop not heating enough, overheating or staying at a fixed heat. This burner switch is a vital component for your stovetop and if it presents any of those issues, it needs to be replaced immediately. A screwdriver, set of pliers and wiring diagram will be needed for the replacement and installation process, and you will need to remove your appliance from the wall outlet first. Remove the knobs from the control panel and then gain access to the underneath portion of it with your screwdriver and disconnect the switch. Remove the wires from the burner switch with a set of pliers and disconnect the securing screws holding the switch in place. Now, you can install the new switch and reassemble the panel, being mindful of wiring each connector to the appropriate wire.
Installation Instructions
James H from Oxford, NY
Burner had one temperature--hot, regardless of setting
1. Killed power and removed the regulator's knob, noted the position of the old control.
2. Took off the cover for the center vent and loosened the two screw holding the housing in place--the screws didn't have to come out completely as it is a U-shaped friction hold.
3. Unscrewed the two screws holding the old control switch in ... Read more place--lifted the housing enough to get at the old switch and carefully pulled it loose--it was a front burner so the control switch was about as far back as it could be but still wasn't that hard to get at.
4. Turned the new switch to orient the wire connectors, then, using a needle-nose pliers, removed each friction connector, one at a time, and fitted them on the new switch (note: one of the wires fitted best if it went under as opposed to around the base of the new switch).
5. Replaced the control back through the housing and screwed it in place, making sure the orientation of the control matched the way it looked originally.
6. Slide the housing back over the two screws and tightened, replace vent.
7. Replaced the knob and turned on the power.
(The above took me about twice as long to write as it did to make the repair and I write professionally but am not a professional electrician.)
Also, I bought a second control switch because, given the age of the unit, I'm sure another one will go. The second one will assure that it won't happen :-).
2. Took off the cover for the center vent and loosened the two screw holding the housing in place--the screws didn't have to come out completely as it is a U-shaped friction hold.
3. Unscrewed the two screws holding the old control switch in ... Read more place--lifted the housing enough to get at the old switch and carefully pulled it loose--it was a front burner so the control switch was about as far back as it could be but still wasn't that hard to get at.
4. Turned the new switch to orient the wire connectors, then, using a needle-nose pliers, removed each friction connector, one at a time, and fitted them on the new switch (note: one of the wires fitted best if it went under as opposed to around the base of the new switch).
5. Replaced the control back through the housing and screwed it in place, making sure the orientation of the control matched the way it looked originally.
6. Slide the housing back over the two screws and tightened, replace vent.
7. Replaced the knob and turned on the power.
(The above took me about twice as long to write as it did to make the repair and I write professionally but am not a professional electrician.)
Also, I bought a second control switch because, given the age of the unit, I'm sure another one will go. The second one will assure that it won't happen :-).
Read less
This is a push-and-turn switch. This kit includes all necessary hardware to install the part. Switch comes with a D-shaped shaft.
This is a push-and-turn switch. This kit includes all necessary hardware to install the part. Switch comes with a D-shaped shaft.
Installation Instructions
Michael from Eden, VT
Regular Parts Replacement/Maintenance.
We love our Jenn-Air electric range that we have owned since 1983 and couldn't get parts from where we bought it recently. We called around to Sears and other appliance dealers and they couldn't help us. We found your company searching on the internet and we are very much pleased with your parts listing and your great service. We will be
... Read more
back. Jody and Mike Hayden, Eden, Vt.
Read less
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
The surface element control switch is an essential component in electric ranges, responsible for regulating the heat output of the surface burner. It allows you to adjust the temperature levels by controlling the electrical flow to the burner. If your stovetop burner fails to turn on, stays on high heat, or doesn’t respond to adjustments, a faulty switch could be the cause. This switch features a double flat shaft design and is nut-mounted for secure installation. Always disconnect the power supply before replacing the switch to prevent electrical hazards. Ensure compatibility with your appliance model before purchasing.
The surface element control switch is an essential component in electric ranges, responsible for regulating the heat output of the surface burner. It allows you to adjust the temperature levels by controlling the electrical flow to the burner. If your stovetop burner fails to turn on, stays on high heat, or doesn’t respond to adjustments, a faulty switch could be the cause. This switch features a double flat shaft design and is nut-mounted for secure installation. Always disconnect the power supply before replacing the switch to prevent electrical hazards. Ensure compatibility with your appliance model before purchasing.
Installation Instructions
Malcolm from White House, TN
Burner Switch Broke were Knob attached
First I cut off power supply, removed screws that held panel on, pulled the switch up and disconnected wires. Installed new switch, being sure to connect wires in the correct places. Refastened panel to stove top. Turned power back on and tested switch and it Worked.
Does your appliance need a quick fix? Our GE Controller Assembly is here to help. This genuine GE part is the heartbeat of your appliance, keeping everything running smoothly and efficiently. It's specifically designed to fit your GE appliances perfectly, meaning you won't have to worry about any compatibility issues. This precision-crafted part doesn?t just improve appliance performance - it enhances its life and reliability too. The GE Controller Assembly is made with sustainability in mind, promising durability that makes for a lasting solution to your appliance woes. When you choose to repair your appliance with this GE part, you're choosing superior results and reliability. It's a simple, effective way to restore your appliance to its former glory. So why wait? Lay your worries to rest and boost your appliance's efficacy with the GE Controller Assembly.
Does your appliance need a quick fix? Our GE Controller Assembly is here to help. This genuine GE part is the heartbeat of your appliance, keeping everything running smoothly and efficiently. It's specifically designed to fit your GE appliances perfectly, meaning you won't have to worry about any compatibility issues. This precision-crafted part doesn?t just improve appliance performance - it enhances its life and reliability too. The GE Controller Assembly is made with sustainability in mind, promising durability that makes for a lasting solution to your appliance woes. When you choose to repair your appliance with this GE part, you're choosing superior results and reliability. It's a simple, effective way to restore your appliance to its former glory. So why wait? Lay your worries to rest and boost your appliance's efficacy with the GE Controller Assembly.
Installation Instructions
Robert from Monroe, NJ
Burners were intermittently working.
It turns out that the 6" and 8" burners we actually broken and the infinite switch for the 8" burner was not working properly. These we very simple replacements. You just need to note the numbers on the original burners to make sure that you use the same numbers on the bottom of the burners so that they install in the same slots. The
... Read more
wires on the infinite switch match and this takes less than 5 minutes to remove the back of the stove top and the front switch handle. Simple replace the infinite switch and the burners and whoowhooo ,,.... the fix is done.
Read less
Installation Instructions
Albert from VALLEY MILLS, TX
Switch to the left front burner not working right.
Repair has not been made yet still waiting for the part. The part is on order and was told it would be shipped in 1/3 business days. Still waiting for the part to come from China. This is the problem with parts being made out side the U. S. A.
This switch is used to operate the dual surface burner.
This switch is used to operate the dual surface burner.
Installation Instructions
Michael from Collierville, TN
Outer element of dual element burner didn't work
Remove Ceran Galss top by removing hex screws below the rim. Also remove the two opposing screws in the center of the downdraft opening. Ceran top comes off easily now.
The instructions with the new switch were very poorly written, so here is how I got the new switch to work:
Attach the black wire(s) from the old switch (termi ... Read more nal 2) to the new switch terminal P1. Also attach the jumper cable to P1 and "jump" it to S1.
Attach the orange wire (old switch terminal 5) to S2
Attach the yellow wire (old switch terminal 4) to 4a
Attach the tan/(white?) wire (old switch terminal 3) to terminal 4 on the new switch
Attach the single red wire from the right front element to terminal 2 on the new switch.
Attach the 'compound' red wires (the ones that come from the left rear/outlet connection and is also attached to the right rear switch) to terminal P2 on the new switch.
There is no need to seperate the compound red wires as the instructions might lead you to believe.
Good Luck
The instructions with the new switch were very poorly written, so here is how I got the new switch to work:
Attach the black wire(s) from the old switch (termi ... Read more nal 2) to the new switch terminal P1. Also attach the jumper cable to P1 and "jump" it to S1.
Attach the orange wire (old switch terminal 5) to S2
Attach the yellow wire (old switch terminal 4) to 4a
Attach the tan/(white?) wire (old switch terminal 3) to terminal 4 on the new switch
Attach the single red wire from the right front element to terminal 2 on the new switch.
Attach the 'compound' red wires (the ones that come from the left rear/outlet connection and is also attached to the right rear switch) to terminal P2 on the new switch.
There is no need to seperate the compound red wires as the instructions might lead you to believe.
Good Luck
Read less
