Jenn-Air Range Wire Plugs and Connectors
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Jenn-Air Range Wire Plugs and Connectors
Your Price
$13.91
In Stock
Jenn-Air Range Surface Burner Receptacle Kit
My sister's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts.
The element is working great now.
Whenever I need appliance parts again I'll use partselect.com. Read more...
PartSelect Number PS1570190
Manufacturer Part Number 12001676
The tools you will need to replace the surface burner receptacle kit on your range include a Phillips screw driver, and a pair of wire strippers. Before doing this repair, make sure to disconnect your appliance from the power supply and wear work gloves to protect your hands. The surface burner receptacle kit comes with a plastic block, high temperature wire nuts, a metal bracket, and wires. This part functions as the connection between the wire harness and the surface element in your range.
Fixes these symptoms
- Element will not heat
- Will Not Start
- See more...
Installation Instructions
Richard from Carthage, NC
Stove top element not working due to bad receptacle.
Turned off the power at the breaker box, cut the wires approximately 5 inches from the bad receptacle and removed it after removing one screw. Stripped back the wires about 1/2 inch and attached the new wires with the ceramic wire nuts provided and secured the receptacle back in place with the new screw provided in the kit.My sister's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts.
The element is working great now.
Whenever I need appliance parts again I'll use partselect.com. Read more...
Your Price
$34.09
In Stock
Jenn-Air Range Terminal Block
PartSelect Number PS11750972
Manufacturer Part Number WPW10245259
This part is for oven ranges, it connects individual wires and protects the device from electrical surges, voltages, and current. With this part, the house power is connected to the range wire harness. Some symptoms replacing the terminal block could be a solution for are little to no heat when baking, element will not heat and/or it will not start. This part will prevent loosening and will reduce damage caused by corrosion (by two different metals). Refer to the instructional diagram for further replacement guidance and exact placement. You must unplug the appliance before installing this part and wear gloves to protect your hands.
Fixes these symptoms
- Element will not heat
- Little to no heat when baking
- Touchpad does not respond
- See more...
Installation Instructions
Joseph from Decatur, GA
Burned terminal block and filter board
Removed and replaced above named parts, rewired.Be sure to tighten all nuts that secure wires. I believe this is what caused the problem.
Read more...
Your Price
$19.60
In Stock
Jenn-Air Range Terminal Block
PartSelect Number PS11747341
Manufacturer Part Number WP9761958
This is the terminal block for the power cord on an electric range.
Fixes these symptoms
- Element will not heat
- Will Not Start
- See more...
Installation Instructions
Wesley from Spring Hill, FL
stove/oven started popping like the 4th of July while on
Terminal block burned up along with 220 cord & front burner. With breaker off, disconnected the block & cord....and assembled new parts. Next, took 2 screws out of stove top and lifed stovetop up. Disconnected bracket holding burner-took off old burner & reattached new burner. Reattached bracket and put back screws..turn on breaker and everything is like new. Do not recommend service companies to do these repairs. Excellent service with this company on receiving parts within 24 hours. Original manufacturers mark up their prices 30-40% more...Part Select is the way to go. Thank you for your execellent service.
Read more...
Your Price
$24.59
In Stock
Jenn-Air Range Main Power Terminal Block
PartSelect Number PS11745232
Manufacturer Part Number WP8203546
Sold individually.
Fixes these symptoms
- Will Not Start
- See more...
Installation Instructions
Frank from Silverhill, AL
Your Price
$47.69
In Stock
Jenn-Air Range Cartridge Receptacle
PartSelect Number PS11757565
Manufacturer Part Number WPY702434
This cartridge receptacle is almost four inches long. It is white in color and is made of ceramic.
Fixes these symptoms
- Element will not heat
- See more...
Installation Instructions
Stephen from Andover, MA
Infinite switch ran more than one burner
Purchased 1 infinite switch and installed it on the left front burner. problem still there so I used the switch that I replaced on the rear burner and all was ok. The front switch had been sending full heat to the rear burner,but the problem ended up with the rear switch. The switches are interconnected and all are the same part number.Diagrams on partsselect were the key to a successful repair.To access the switch you need only to remove the fan cover, remove the 2 screws holding the switch assembly and move it foreward and then lift to reveal slide on connectors. Power to the unit is off at the main panel during the entire process.
Read more...
Your Price
$86.70
In Stock
Jenn-Air Range Meat Probe Receptacle
PartSelect Number PS1486371
Manufacturer Part Number 8186589
This is just the receptacle. Meat probe is sold separately.
Your Price
$61.33
In Stock
Jenn-Air Range Burner Cartridge Terminal Block
PartSelect Number PS11757594
Manufacturer Part Number WPY708730
No spades or wiring come with this part. To order the spades or wiring, please research by model# of appliance.
Fixes these symptoms
- Element will not heat
- See more...
Installation Instructions
Calvin from Merced, CA
The top would not heat,large or small eye.
Removed the bottom cover and replaced the burned contact spade. Cleaned the wires and adjust the contact holder.
Read more...
Your Price
$13.95
In Stock
Jenn-Air Range Cartridge Male Contact Spade
PartSelect Number PS1988157
Manufacturer Part Number Y708572
This cartridge assembly male contact spade is made of metal. These are sold individually, though each range uses four contact spades.
Fixes these symptoms
- Element will not heat
- See more...
Installation Instructions
Calvin from Merced, CA
The top would not heat,large or small eye.
Removed the bottom cover and replaced the burned contact spade. Cleaned the wires and adjust the contact holder.
Read more...
Your Price
$71.30
In Stock
Jenn-Air Range Element Receptacle Assembly
(2) Removed old element receptacle assembly (note screww attaching the clip to ring was corroded and had to be drilled out and replaced - screw not included), retaining existing element (determined it was good)
(3) Fited up new element receptacle assembly and determined how far the new wires would go, cut the old wires at appropriate point (allowing for wire splice).
(4) Attached new element receptacle assembly using a machine screw I found in my collection
(5) Routed new wires though retaining clips, and spliced into old wires near the cartridge plug (note: be sure to use high temp splice nuts - not supplied in kit)
(6) Installed old element into new receptacle and tested by measuring resistance - element resistance should be about 12 ohms, with all connections to ground reading infinity)
(7) Reassembled cartrige assembly using six machine screws previously removed (note, make sure the part align properly - top inside the bottom)
(8) Put the assembly back on range - worked great! Read more...
PartSelect Number PS11744184
Manufacturer Part Number WP74007474
This part connects the surface burner to the wiring harness.
Fixes these symptoms
- Element will not heat
- See more...
Installation Instructions
Daniel from Great Falls, VA
Range element receptacle had shorted out
(1) Disassembled range element cartridge unit by removing six machine screws on sides(2) Removed old element receptacle assembly (note screww attaching the clip to ring was corroded and had to be drilled out and replaced - screw not included), retaining existing element (determined it was good)
(3) Fited up new element receptacle assembly and determined how far the new wires would go, cut the old wires at appropriate point (allowing for wire splice).
(4) Attached new element receptacle assembly using a machine screw I found in my collection
(5) Routed new wires though retaining clips, and spliced into old wires near the cartridge plug (note: be sure to use high temp splice nuts - not supplied in kit)
(6) Installed old element into new receptacle and tested by measuring resistance - element resistance should be about 12 ohms, with all connections to ground reading infinity)
(7) Reassembled cartrige assembly using six machine screws previously removed (note, make sure the part align properly - top inside the bottom)
(8) Put the assembly back on range - worked great! Read more...
Your Price
$12.30
In Stock
Related Jenn-Air Range Parts
- All Jenn-Air Range parts
- Jenn-Air Range Brackets and Flanges
- Jenn-Air Range Circuit Boards and Touch Pads
- Jenn-Air Range Cooktops
- Jenn-Air Range Doors
- Jenn-Air Range Drip Bowls
- Jenn-Air Range Elements and Burners
- Jenn-Air Range Grates
- Jenn-Air Range Hardware
- Jenn-Air Range Hinges
- Jenn-Air Range Igniters
- Jenn-Air Range Insulations
- Jenn-Air Range Knobs
- Jenn-Air Range Legs and Feet
- Jenn-Air Range Lights and Bulbs
- Jenn-Air Range Panels
- Jenn-Air Range Racks
- Jenn-Air Range Seals and Gaskets
- Jenn-Air Range Switches
- Jenn-Air Range Valves
