My Orders
Jenn-Air Range Motors
GET YOUR OFFICIAL Jenn-Air PARTS TO ENSURE VICTORY
Popular Jenn-Air Range Motors
This control panel cooling fan is a blower motor assembly designed to regulate airflow within the control panel area of select ranges and ovens. Engineered to prevent overheating, it helps maintain optimal operating temperatures for electronic components, thereby extending their lifespan and ensuring consistent performance. The assembly includes a hall sensor for precise monitoring and is intended to replace older fan models across a variety of compatible units. Common symptoms of a failing fan—such as low-speed errors, stalling, or smoke—can be resolved with this replacement.
This control panel cooling fan is a blower motor assembly designed to regulate airflow within the control panel area of select ranges and ovens. Engineered to prevent overheating, it helps maintain optimal operating temperatures for electronic components, thereby extending their lifespan and ensuring consistent performance. The assembly includes a hall sensor for precise monitoring and is intended to replace older fan models across a variety of compatible units. Common symptoms of a failing fan—such as low-speed errors, stalling, or smoke—can be resolved with this replacement.
What this part fixes:
- Element will not heat
- Little to no heat when baking
- Oven is too hot
Installation Instructions
Richard from EUGENE, OR
FE80 Error, blower motor underperforming
Remove cover under controls, unscrew rangetop (front only). Motor on right side of oven directly under rangetop detaches with 3 screws and remove with care. Swap foam seal to new motor and install. May require contact cement to attach seal to new part.
This motor isolator is less than an inch long.
This motor isolator is less than an inch long.
Installation Instructions
John from Berkley, MI
Blower motor died and I needed to replace it
Most of the repair was obvious as I took the blower apart before ordering the parts. Unfortunately the new motor was significantly larger than the original motor so I had to um. Adjust the position of some of the other parts to fit it in. There was a sheet metal flange that was installed on the other side of the blower from the motor whi
... Read more
ch was designed to focus the air flow into the blower. I used a hammer to ajust the angle of flange so it no longer extended as far into the blower housing.
It works just fine although its a bit louder than the old motor was.
It works just fine although its a bit louder than the old motor was.
Read less
Used with down-draft models. This part helps draw the steam and odors through the vent when the fan switch is activated.
Used with down-draft models. This part helps draw the steam and odors through the vent when the fan switch is activated.
Installation Instructions
Steven from Marshfield, MA
Downdraft Blower Failure
Blower motor stopped working and the breaker tripped. Horrible smell! from the somewhere in the oven. Looking at the wiring diagram told me that there was a relay board feeding he motor, but I had no idea where it was, which took a little Internet searching to find it. Finally seeing that it was in the rear I was happy to see that there
... Read more
was enough flexible gas line to pull out the stove enough to check the board, which was fried. I replaced the board and then looked for the reason it smoked and found that the blower motor was shorted (and stank horribly).
It was straighforward to replace, but when I put everything back, NOTHING worked at all - no lights on the control panel, nothing. I then checked the voltage across the terminals and saw 240V and was puzzled until saw that there was no 120V to neutral where the plug connected to the back of the stove. The outlet, however, had 120V to neutral. Since it was a molded plug I thought that was not likey to be a cmmon failure, so after killing th breaker I took off the outlet cover that the stove plugged into and found out that the neutral terminal was intermittent.
The neutral contacts were not grabbing the netral terminal on the plug tightly enough and were a little discolored in one spot. All that moving around of the plug while moving the stove probably moved it just enough not to work at all - that thing was a fire hazard that I'm surprised hadn't been the cause of more damage in a house only 12 years old. Rather than try and clean the termnals and trust bending them to be tighter (and worry about metal fatigue) I spent the $10 so that I could sleep better for a tight new 240V 30A outlet.
Everthing works like a charm now.
It was straighforward to replace, but when I put everything back, NOTHING worked at all - no lights on the control panel, nothing. I then checked the voltage across the terminals and saw 240V and was puzzled until saw that there was no 120V to neutral where the plug connected to the back of the stove. The outlet, however, had 120V to neutral. Since it was a molded plug I thought that was not likey to be a cmmon failure, so after killing th breaker I took off the outlet cover that the stove plugged into and found out that the neutral terminal was intermittent.
The neutral contacts were not grabbing the netral terminal on the plug tightly enough and were a little discolored in one spot. All that moving around of the plug while moving the stove probably moved it just enough not to work at all - that thing was a fire hazard that I'm surprised hadn't been the cause of more damage in a house only 12 years old. Rather than try and clean the termnals and trust bending them to be tighter (and worry about metal fatigue) I spent the $10 so that I could sleep better for a tight new 240V 30A outlet.
Everthing works like a charm now.
Read less
This is a blower motor for your range, but you may also know it as a blower fan motor or a downdraft vent fan motor. This part is used with down draft models. It helps draw the steam and odors through the vent for the stove top when the switch is activated. The blower motor has a diameter of five inches. The shaft on this model has a 3/8-inch diameter with a counter clockwise rotation. This motor includes the foam seal.
This is a blower motor for your range, but you may also know it as a blower fan motor or a downdraft vent fan motor. This part is used with down draft models. It helps draw the steam and odors through the vent for the stove top when the switch is activated. The blower motor has a diameter of five inches. The shaft on this model has a 3/8-inch diameter with a counter clockwise rotation. This motor includes the foam seal.
Installation Instructions
Janellen from Aiken, SC
blower motor died
Pulled the motor and blower wheel from below. Replaced both. I think it was easier to replace the two together than just the motor.I also had old light indicators so we replaced them since the stove was sort of apart. The repair was not difficult at all, and my 30+ stove top looks and runs great!
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
This blower motor moves air through the appliance to support ventilation, cooling, or heating functions. Proper airflow helps maintain efficiency and protect internal components. Replacing a worn or noisy blower motor can restore consistent performance.
This blower motor moves air through the appliance to support ventilation, cooling, or heating functions. Proper airflow helps maintain efficiency and protect internal components. Replacing a worn or noisy blower motor can restore consistent performance.
This fan motor assembly is a genuine OEM replacement designed for ranges and ovens, ensuring proper air circulation during operation. Its primary role is to rotate the convection or cooling fan blade, which helps maintain stable temperatures for even cooking and prevents overheating of essential electronic components. By promoting consistent airflow, this part supports optimal performance and reliability. For safety, always disconnect power before installation and follow the manufacturer’s instructions.
This fan motor assembly is a genuine OEM replacement designed for ranges and ovens, ensuring proper air circulation during operation. Its primary role is to rotate the convection or cooling fan blade, which helps maintain stable temperatures for even cooking and prevents overheating of essential electronic components. By promoting consistent airflow, this part supports optimal performance and reliability. For safety, always disconnect power before installation and follow the manufacturer’s instructions.
Convection fan assembly circulates hot air through the oven for even heating.
Convection fan assembly circulates hot air through the oven for even heating.
