This door hinge can be used for the left or right side. As per the manufacturer if the hinges have never been replaced on the appliance, they suggest to replace the door hinge receptacle kit.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Castor R - May 3, 2023
Verified Purchase
Replace hinge on my oven door
The new part worked well. Easy to replace. 30 minutes is all it took.
★★★★★
★★★★★
ALAN S - December 26, 2022
Verified Purchase
Exact part, mint condition-cavalier about delivery
Great part - ordered wee AM hrs day before Thanksgiving, paid top dollar for priority delivery, but didn't touch the part for shipping until after Thanksgiving, not cool.
★★★★★
★★★★★
Gary L - March 5, 2019
Verified Purchase
Jenn-Air oven door hinges
The parts were packaged differently but were a perfect fit. I recommend viewing tutorials on You Tube. What they did not mention in the tutorial is that the screws that hold the door together (top and bottom) must be removed in order to remove/install the part; but this is common when you look at the door assembly. The parts installed in minutes and the oven is like new again.
★★★★★
★★★★★
Carl B - January 21, 2019
Verified Purchase
Failed
Repair seemed to go well but hinges failed after second use. Locked up and couldn’t disengage. Needed to replace oven.
January 22, 2019
Hello,
Thank you for leaving a review on the part ordered. I have sent you an email in regards to the order. Hope to hear from you!
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.8 / 5.0, 9 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Oven door would not close tightly
Remove door Remove front cover of door Remove hinge screws Put back together.
Allen from PISGAH FOREST, NC
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I leaned on the door and broke the hindge
I had a lot of trouble unlocking the door hindge you must pull the door out to change the hinge they are on the hinge and slide foward then pull the door up and out lay the door flat on a table cover the table with a towel so you don't scrach either one. Unscrew 6 screws on the door cover. 3 on top 3 on bottom take the cover off the hinges are exposed there 3 screws on the hinge 1 on the front and 2 on the bottom replace hinges install face insert door and lock the hinge it's all done. I wish I had these directions
Norman from Brockton, MA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
14 of 23 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the oven door would not shut all the way, so heat was leaking
The part fit perfectly.Ther repair was logic. The door was of course heavy . I needed an extra hand. I would have appreciated of instructions were included with the part. Also a web link on how to do it would alos have helped greatly
mohaemd from pittsburgh, PA
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
4 of 10 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My wife dropped a cast iron dish on the door while it was open, bent the hinges, so it would not close properly.
It was really easy, just lift the door off from the range, I set it down on the box that the hinges came in, took the six screws out to release the front fascia of the door from the back, hinges are right there, un-screw and install the new hinges, put everything back together in reverse and lift the door back on to the range, less than 10 minutes!
Barry from Barre, VT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
4 of 6 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replaced faulty door hinge and installed tip-over bracket to floor
removed door (no tools required - just lift and pull door out of range). removed front door panel with a screwdriver. removed/replaced door hinge with nutdriver. replaced front door panel with screwdriver. replaced door on range (again, no tools required). then installed tip-over bracket to floor/wall behind range. measured location, drilled pilot holes and installed wood screws into the floor and rear wall stud.
First I released the lock on the oven door hinge so that I could take the door off by lifting it up and out. Then it was just a matter of removing screws, replacing the hinges, and putting it back together. I did have to guess a little as I started removing screws as I wasn't sure exactly what to remove, but it became pretty self evident as I looked it over. Not as bad as I had expected.
Odin from Warrensburg, MO
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
15 of 29 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door won't close properly
Removed and replace the old spring and it close properly again.
Removed door from oven. Removed 6 screws to dismantle door. Removed 3 more screws to remove hinge from door...reverse order to assemble. Very easy
Jeff from Syracuse, UT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
2 of 9 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The door was stepped on and did not open or close correctly
I took the door off, removed the inside of the oven door and replaced the three screws for each hinge. I replaced the inside of the oven door and put the door back on and everything worked GREAT.
Ask our experts a question about this part and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Robert
November 8, 2017
Got the door off can not get it back on
For model number AER5715QAW
Hi Robert,
Thank you for your question. You should be able to slide your door back on to the hinges. We did have a customer who wrote in with some instructions that may help you: " I had a lot of trouble unlocking the door hindge you must pull the door out to change the hinge they are on the hinge and slide foward then pull the door up and out lay the door flat on a table cover the table with a towel so you don't scrach either one. Unscrew 6 screws on the door cover. 3 on top 3 on bottom take the cover off the hinges are exposed there 3 screws on the hinge 1 on the front and 2 on the bottom replace hinges install face insert door and lock the hinge it's all done. " I hope that helps. Good luck with your repair.
3 people found this helpful.
Was this helpful?
Thank you for voting!
E T
December 18, 2017
The springs on this oven door produce loud "stretching" noise when the door is opened or closed, especially when hot. Do i need to replace them is there some way to quiet them ? I found the hinge/spring assembly # 74010546. Is the spring availablr alone or must i replace the entire assembly ? Thanks, eti
For model number MERH 752BAN
Hi E T,
Thank you for your question. If your door hinges are making a loud noise when you open the door, especially when it is hot, you will need to replace them. I hope this helps. Thank you and have a great day!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Lenny
November 8, 2019
Oven door does not close tight
For model number MER5755QAW
hello Lenny, Thank you for the question. I suggest checking the Door Hinges PartSelect Number PS2087906 and the Hinge Receptacle PartSelect Number PS11744396 for wear or damage. Hope this helps!
Hello - We replaced the hinges on the door from your company maybe 2 years ago. When I opened the door the other day, the right-side hinge came loose and was disengaged from the oven. We were unable to reconnect the oven door. I think we need to replace the hinges with the PS2087906 hinges (MFG #7401546), but do we need to replace the door hinge receptacle kit as well? Thank you.
For model number AER5735QAW
Hello Deanne, thank you for the question. The manufacturer recommends replacing both the hinges and the receptacles. We recommend replacing the hinge receptacle, part number PS11744396, to fix your issue. We hope this information is useful!
