Frigidaire Dryer Wheels and Rollers
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Frigidaire Dryer Wheels and Rollers
Your Price
$36.85
In Stock
Frigidaire Dryer Drum Roller
PartSelect Number PS12741852
Manufacturer Part Number 5304523152
This is a genuine replacement drum roller for a dryer. This part includes a roller which has an axle and two tri-rings. The dryer drum roller holds the drum in place while it rotates on the dryer support wheels. If rollers are worn out, the dryer will be noisy. This is a genuine OEM replacement part. If your dryer has more than one drum support roller, it is recommended to replace both at the same time to ensure proper rotation. They often wear at the same rate. You will need to remove the outer front panel to access this part. This replacement part is sold separately.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Philip from Oakland, CA
Noisy Dryer
When I described the noise to a YouTube appliance diagnostician, I was directed to check the felt seals front and back of the rotating drum for wear, tears, or foreign objects. As it happens the felt seals looked find and there were foreign objects so, not wanting to disassemble and reassemble the dryer more than I had, I ended up replacing all the replaceable moving parts that I considered possible culprits: The idler tension spring, the idler tension bracket (which includes a nylon pulley wheel), the drum belt, the five rubber-tipped bearings that support the drum and keep it in place, and the foam seal on the blower housing which seemed a little brittle and old, as well as high-temperature adhesive for the latter. The instructional videos here and on YouTube were extremely helpful (I doubt that I would have attempted this job at all, had I not watched these ahead of time). The most time-consuming aspect was waiting for the arrival of the parts as I didn't order them all at the same time or all from the same place (I ordered from whomever could ship me a given part the fastest. Disassembly took less than an hour. Re-assembly with the new parts in place took about the same but was a little more awkward because this appliance sits in a very narrow closet and it's difficult to ensure that the 4" flexible duct stays in place when sliding the appliance back into the closet. No regrets. Now I know the basics if this dryer needs attention in future and I also know all the parts that I can eliminate as suspects in any future maintenance (the parts that I replaced)
Read more...
Your Price
$105.32
In Stock
Frigidaire Dryer Blower Housing With Wheel
The top panel was easily taken off by removing 2-screws from the back edge of the panel, and sliding it back to release it from the front panel seam.
The front panel is more involved, but still relatively easy for your average "do-it-yourselfer". I removed the front door panel by first removing the control panel (4-screws; 2 on top and 2 from the back of the panel). I removed 2 cable assemblies from the control panel via connecters (different sizes so didn't need to mark) and 2-wires attached to the large control panel mode selector (I marked these 2-wires). I set aside the control panel. I removed the front door panel by taking off 6-screws (2 on top, 2 on the bottom, and the remaining 2 on the inside of the panel on either side of the drum). After removing these 6-screws, I carefully pulled the front door panel away from the front of the dryer, carefully releasing 4-alignment latches (2 on either side). The front door panel was still electrically attached to the machine so I had to disconnect a couple more wires. I carefully disconnected 2-wires from the door light assembly and 3 more wires from the door switch (I marked the 3-wires on the door switch). I set aside the front door panel.
From the back of the dryer, I removed the small motor access panel on the bottom left corner. This panel also provides access to the drum belt. I released the drum belt from the motor drive wheel by releasing spring tension at the tensioner. The belt can easily be disconnected from the motor drive wheel and tensioner assemblies.
Removal of the drum was now possible. With the front door panel removed, the front of the drum is maintained in place via a small plastic stop on the top crossmember. I removed this stop prior to removing the drum. With one hand, carefully grabbing the belt that is was loosely draped across the back of the drum, and the other hand holding the front lip of the drum, I provided a quick and forceful upward motion to the back of the drum in order to dislodge the drum shaft from the bearing housing assembly. Once this was accomplished, I simple pulled the drum out of the dryer housing via the front of the machine.
The drum bearing repair kit ordered came with the replacement ball bearing, bearing housing, drum shaft, high-temperature grease, and attaching hardware.
I replaced the drum shaft on the drum via the 4-screws accessed on the drum rear panel.
I removed the old bearing/bearing housing via the 2-screws holding it in place. I wasn't too concerned about loosing the small ball bearing as the kit provided me a new one. I generously applied some high-temperature grease to coat the interior lining of the new bearing housing. I also placed a dab on the back seat where the new ball bearing sits. This helped hold the bearing in place while reattaching it. I reinstalled the bearing housing to finish replacing the repair parts.
Reassembly of the drum is in the reverse order. I paid particular attention to making sure the new drum shaft properly seated with the new drum bearing housing.
After reinstalling the drum and while the front door panel was still off the dryer, it was easy to inspect the blower housing. I found the squirrel cage had broken loose from the molded nut that attaches it to the motor shaft. That would explain the heat problem; the heat was not being exhausted through the duct.
THE SQUIRREL CAGE IS REVERSE THREADED. I was unable to remove the nut from the motor shaft as the design encompasses a metal bushing molded into a plastic nut shaped form. The plastic would not hold up to the force I was applying trying to loosen the squirrel cage. So I ended up removing the entire motor and blower housing assembly from the base Read more...
PartSelect Number PS418726
Manufacturer Part Number 131775600
***Please Note: This part is a substituted part by the manufacturer. It may appear different, but should still work with your appliance.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Gerald from Cumming, GA
Had 2-seperate problems; 1st was a high pitch squeel, 2nd was the cover overheating
The high pitch squeel was the result of a failing drum bearing. It was particularly evident when first turning on the dryer, but became softer as the dryer heated up. In order to replace the drum bearing, I removed the top panel and front door panel.The top panel was easily taken off by removing 2-screws from the back edge of the panel, and sliding it back to release it from the front panel seam.
The front panel is more involved, but still relatively easy for your average "do-it-yourselfer". I removed the front door panel by first removing the control panel (4-screws; 2 on top and 2 from the back of the panel). I removed 2 cable assemblies from the control panel via connecters (different sizes so didn't need to mark) and 2-wires attached to the large control panel mode selector (I marked these 2-wires). I set aside the control panel. I removed the front door panel by taking off 6-screws (2 on top, 2 on the bottom, and the remaining 2 on the inside of the panel on either side of the drum). After removing these 6-screws, I carefully pulled the front door panel away from the front of the dryer, carefully releasing 4-alignment latches (2 on either side). The front door panel was still electrically attached to the machine so I had to disconnect a couple more wires. I carefully disconnected 2-wires from the door light assembly and 3 more wires from the door switch (I marked the 3-wires on the door switch). I set aside the front door panel.
From the back of the dryer, I removed the small motor access panel on the bottom left corner. This panel also provides access to the drum belt. I released the drum belt from the motor drive wheel by releasing spring tension at the tensioner. The belt can easily be disconnected from the motor drive wheel and tensioner assemblies.
Removal of the drum was now possible. With the front door panel removed, the front of the drum is maintained in place via a small plastic stop on the top crossmember. I removed this stop prior to removing the drum. With one hand, carefully grabbing the belt that is was loosely draped across the back of the drum, and the other hand holding the front lip of the drum, I provided a quick and forceful upward motion to the back of the drum in order to dislodge the drum shaft from the bearing housing assembly. Once this was accomplished, I simple pulled the drum out of the dryer housing via the front of the machine.
The drum bearing repair kit ordered came with the replacement ball bearing, bearing housing, drum shaft, high-temperature grease, and attaching hardware.
I replaced the drum shaft on the drum via the 4-screws accessed on the drum rear panel.
I removed the old bearing/bearing housing via the 2-screws holding it in place. I wasn't too concerned about loosing the small ball bearing as the kit provided me a new one. I generously applied some high-temperature grease to coat the interior lining of the new bearing housing. I also placed a dab on the back seat where the new ball bearing sits. This helped hold the bearing in place while reattaching it. I reinstalled the bearing housing to finish replacing the repair parts.
Reassembly of the drum is in the reverse order. I paid particular attention to making sure the new drum shaft properly seated with the new drum bearing housing.
After reinstalling the drum and while the front door panel was still off the dryer, it was easy to inspect the blower housing. I found the squirrel cage had broken loose from the molded nut that attaches it to the motor shaft. That would explain the heat problem; the heat was not being exhausted through the duct.
THE SQUIRREL CAGE IS REVERSE THREADED. I was unable to remove the nut from the motor shaft as the design encompasses a metal bushing molded into a plastic nut shaped form. The plastic would not hold up to the force I was applying trying to loosen the squirrel cage. So I ended up removing the entire motor and blower housing assembly from the base Read more...
Your Price
$77.75
In Stock
Frigidaire Dryer Drum Roller Kit
PartSelect Number PS12746506
Manufacturer Part Number 5304523155
This is a genuine replacement drum roller for a dryer. This part includes a roller which has an axle and two tri-rings. The dryer drum roller holds the drum in place while it rotates on the dryer support wheels. If rollers are worn out, the dryer will be noisy. This is a genuine OEM replacement part. If your dryer has more than one drum support roller, it is recommended to replace both at the same time to ensure proper rotation. They often wear at the same rate. You will need to remove the outer front panel to access this part. This replacement part is sold separately.
Fixes these symptoms
- Noisy
- See more...
Your Price
$59.35
In Stock
Frigidaire Dryer Idler Arm Assembly
DISCONNECT ELECTRICITY and GAS LINES
1.popped top by pushing and prying at front /top clips about 2-3in. in from side edges. lifted it off
2. removed the front panel by removing the 2 top front screws from the inside, then the two lower screws from the front after removing the small white plastic hole covers. disconnected the multiplug electric connector top right. set panel aside.
3.remove small back panel.and loosened belt.(observe belt path and idle pulley assy.
4. lifted drum and slid it out the front.
5. using socket, removed rear plastic bearing housing and replaced the same. be careful of observing the small ball bearing and the small piece on outside back panel. replace the same. you wil probably need a second set of hands to hold the piece on the outside when screwing in the screws from the inside.
6. unscew the "bearing" from the rear of the drum and replace with new one.(the screws are self-tapping and go in HARD!!)
7. apply lubricant liberally to plastic bearing holder
8. place new belt around drum(rubber side against drum cloth side out.
9. idle pulley assy. is removed by removing spring and just sliding assy out of holder. replace with new
10. replace drum and belt
11. take front panel and remove top drum glide and lower basket seal.( i marked where the two seal/glide come together with a marker )
12. scrape and remove as much felt and possible. I then used "goo gone" to remove all the glue. clean well and using the provided high temp adhesive reattached glide and seal.
13. reassemble and enjoy your NEW? dryer Read more...
PartSelect Number PS1156706
Manufacturer Part Number 131863007
Part may differ in color from image. Please note that this is only a cosmetic difference.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
john from owego, NY
clothes got caught , burned and ripped on front of drum
I felt ,if I was going to replace the top drum glide and lower basket seal, I might as well replace the belt ,bearing assembly and the idle pulley assembly and avoid having to replace these sooner than later. All of the parts showed alot of wear and the belt like all drive belts, should be changed every 5-6 years.DISCONNECT ELECTRICITY and GAS LINES
1.popped top by pushing and prying at front /top clips about 2-3in. in from side edges. lifted it off
2. removed the front panel by removing the 2 top front screws from the inside, then the two lower screws from the front after removing the small white plastic hole covers. disconnected the multiplug electric connector top right. set panel aside.
3.remove small back panel.and loosened belt.(observe belt path and idle pulley assy.
4. lifted drum and slid it out the front.
5. using socket, removed rear plastic bearing housing and replaced the same. be careful of observing the small ball bearing and the small piece on outside back panel. replace the same. you wil probably need a second set of hands to hold the piece on the outside when screwing in the screws from the inside.
6. unscew the "bearing" from the rear of the drum and replace with new one.(the screws are self-tapping and go in HARD!!)
7. apply lubricant liberally to plastic bearing holder
8. place new belt around drum(rubber side against drum cloth side out.
9. idle pulley assy. is removed by removing spring and just sliding assy out of holder. replace with new
10. replace drum and belt
11. take front panel and remove top drum glide and lower basket seal.( i marked where the two seal/glide come together with a marker )
12. scrape and remove as much felt and possible. I then used "goo gone" to remove all the glue. clean well and using the provided high temp adhesive reattached glide and seal.
13. reassemble and enjoy your NEW? dryer Read more...
Your Price
$45.82
In Stock
Frigidaire Dryer Blower Wheel
PartSelect Number PS417911
Manufacturer Part Number 131476300
This blower wheel is a genuine OEM replacement part for your dryer. The wheel can become damaged through use of the dryer, especially if the drive motor shaft, which it is attached to, becomes damaged. This repair will require some disassembly of the dryer. Make sure to disconnect the power source and wear appropriate work gloves while conducting this repair.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Jeffrey from Gulf Breeze, FL
dryer squeeked and rattled
after removing the panel covering the dryer blower and removing the blower cover, i pulled the old blower wheel off and placed the new whell on carefully lining the flat edge of the wheel hole up with the flat edge on the blower piston, the n i placed the clamp on and put back all the housing covers and panels...and now my dryer runs quiet and drys cloths fast....thanks to partselect!!!!
Read more...
Your Price
$37.91
In Stock
Frigidaire Dryer Roller
PartSelect Number PS12731677
Manufacturer Part Number 807787702
This roller supports smooth sliding or rotation of components by reducing friction and maintaining alignment. It is commonly replaced when movement becomes rough, noisy, or restricted.
Your Price
$140.58
In Stock
Frigidaire Dryer Blower Wheel With Housing
Connected electrical plugs to motor. Put drum in and plastic piece in front top of dryer. Hooked belt back up from rear. Replaced rear door. (2 screws). Reconnected ground wire on back top of dryer. Put on front making sure all wires to Timer are connected(they can pull off when taking drum out). Close front. Polug dryer in. Reset dryer in place. Turn on Breaker. Done. Read more...
PartSelect Number PS419097
Manufacturer Part Number 131967600
This part includes the blower wheel, housing and cover. These 3 parts are not available separately. Must order full assembly.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
RICHARD from MERCHANTVILLE, NJ
Dryer stopped every 5 minutes. Had to be hand turned to stop.
Repair to replace motor and blower kit. Disconnected Power Source and turned off breaker. Removed top and front with screwdriver. Removed back plate with screwdriver. Disengaged belt. Removed plastic piece in front top with phillip screwdriver. Removed Drum. Disconected thermostat from blower. Unplugged motor connections. Removed screws holding in blower unit. Removed blower unit and motor as a unit. Removed pully unit (2 Screws). Took off blower unit security nut to be used on new unit. Took old seal out of pully unit. (New Motor has one installed on it). Put pully unit back in. Put in new motor and blower unit. Screwed them in place. Reconnected thermostat. (2 screws).Connected electrical plugs to motor. Put drum in and plastic piece in front top of dryer. Hooked belt back up from rear. Replaced rear door. (2 screws). Reconnected ground wire on back top of dryer. Put on front making sure all wires to Timer are connected(they can pull off when taking drum out). Close front. Polug dryer in. Reset dryer in place. Turn on Breaker. Done. Read more...
Your Price
$36.85
Special Order
Your Price
$110.59
Special Order
Your Price
$100.27
Special Order
Related Frigidaire Dryer Parts
- All Frigidaire Dryer parts
- Frigidaire Dryer Bearings
- Frigidaire Dryer Belts
- Frigidaire Dryer Brackets and Flanges
- Frigidaire Dryer Caps and Lids
- Frigidaire Dryer Circuit Boards and Touch Pads
- Frigidaire Dryer Doors
- Frigidaire Dryer Drawers and Glides
- Frigidaire Dryer Drums and Tubs
- Frigidaire Dryer Ducts and Vents
- Frigidaire Dryer Elements and Burners
- Frigidaire Dryer Fans and Blowers
- Frigidaire Dryer Filters
- Frigidaire Dryer Fuses
- Frigidaire Dryer Handles
- Frigidaire Dryer Hardware
- Frigidaire Dryer Hinges
- Frigidaire Dryer Hoses and Tubes
- Frigidaire Dryer Knobs
- Frigidaire Dryer Latches
- Frigidaire Dryer Lights and Bulbs
- Frigidaire Dryer Motors
- Frigidaire Dryer Panels
- Frigidaire Dryer Pulleys
- Frigidaire Dryer Seals and Gaskets
- Frigidaire Dryer Sensors
- Frigidaire Dryer Springs and Shock Absorbers
- Frigidaire Dryer Switches
- Frigidaire Dryer Thermostats
- Frigidaire Dryer Timers
- Frigidaire Dryer Trims
- Frigidaire Dryer Valves
- Frigidaire Dryer Wire Plugs and Connectors