Amana Dryer Brackets and Flanges

Amana Appliance Parts
Shop By Part Type

Popular Amana Dryer Brackets and Flanges

Your Price
$41.30
  In Stock
Stacking Kit
★★★★★
★★★★★
(1)
PartSelect Number PS990537
Manufacturer Part Number 8572546
This kit allows you to stack your washer and dryer to maximize your laundry space.
Your Price
$54.31
  In Stock
STACK KIT FOR LONG VENT DRYER
★★★★★
★★★★★
(1)
PartSelect Number PS12069913
Manufacturer Part Number W10869845
Installation Instructions
Nelson from Middletown, NY
Washer Would Drain But Not Spin
Removed rear cover (6 screws) unpluged harness from motor control and removed same. Replaced motor control reinstalled harness. Replaced rear cover. Parts used motor control board. Read more...
Your Price
$44.23
  In Stock
Stacking Kit
★★★★★
★★★★★
(6)
PartSelect Number PS888067
Manufacturer Part Number 8541503
This kit comes with 2 adhesive pads, 2 brackets and 4 screws. This is for stacking the appliances vertically - dryer over washer.
Installation Instructions
Randy from Brentwood, CA
Placing Dryer on Top of Washing Machine with Stack Kit
I purchased a stack kit from "Part select.com". The item was just what I needed to do the job. The delivery of the part was made the next morning. WOW! Excellent service! The process was completed in less than 24 hours, start to finish. Very impressed! Read more...
Your Price
$41.30
  On Order
Plate
PartSelect Number PS11750411
Manufacturer Part Number WPW10208419
Your Price
$51.58
  In Stock
Glide Bracket Kit
PartSelect Number PS2003560
Manufacturer Part Number 12002090
This kit contains two glide brackets and four screws.
Fixes these symptoms
Installation Instructions
David from Underwood, IA
Loud banging sound. Worn out roller.
Pulled off the lower panel with 5/16 socket.Pulled off the door assembly by removing the two screws at the bottom of the door assembly. I pulled down a little and then out. be carefull of the wires. Other posts said to remove. The wires were long enough I did not have to remove them. I just leaned it against the wall. I then removed the 4 screws that hold the front piece in.pulled it off replaced brackets , installed self adhesive felt(stuck good) and then glides. Mine were thin but not the problem. I then reached under the drum and released the belt from the tensioner. I then pulled the whole drum out.This is the time to vacum out good. I could get to the rear rollers very easy. The left roller was shot and the shaft half wore into(the problem). I pulled off the two screws holding the roller support. Normally You have to remove the wheel with snap ring pliers first to remove the support. In this case snap ring long gone. Replaced support shaft, installed thrust washers and roller with grease for both sides. The right support shaft was still good. Removed tensioner pulley and inspected. It was just as good as the new one. Cleaned and greased and reinstalled. Put new belt on the tub and slid it back in. Be carefull to get the belt on the proper side of the tensioner. I then installed the front supprt in place to support the tub with the 4 screws. Spun the tub(felt good) then reached under and reinstalled belt to motor and tensioner. Spun again to check for belt alignment. (Check) Reinstalled door an lower panel. Test Quiet Sounds like new. Very easy! I hope this helps someone just as the other post has helped me. Blessings to all. Read more...
Your Price
$13.22
  On Order
Bracket, Ignitor
PartSelect Number PS11743787
Manufacturer Part Number WP694298
Your Price
$18.36
  In Stock
BRACKET
PartSelect Number PS12070354
Manufacturer Part Number W11032820
Installation Instructions
Edward from Andover, NJ
Dryer was sqeaking loudly when running
I Looked on internet sites for this type of problem.
Most sites said the support rollers could cause this.
I found your site PartSelect and with help of your diagrams of the machine ordered the parts I thought were needed plus other parts that might cause the problem.
With machine torn down I replaced the rollers.
I had also ordered the main drive belt and idler assembly with the rollers and these also needed replacement. It is a good idea to order other suspect parts when doing this type of repair since you can return the parts not needed.
Your return policy is great.

Edward Brennan
Read more...
Your Price
$33.65
  Special Order
BRACKET
PartSelect Number PS383992
Manufacturer Part Number 694538
Your Price
$26.08
  On Order
Bracket
PartSelect Number PS11750406
Manufacturer Part Number WPW10208382
Your Price
$11.30
  On Order
CLIP
PartSelect Number PS334279
Manufacturer Part Number 279771
Installation Instructions
Jeff from OAKLAND, TN
Dryer would not heat and the timer would not turn as it should
I replaced a bad thermostat Read more...

Related Parts