Amana Dryer Hardware | Replacement Parts & Accessories | PartSelect
Our response to COVID-19
We're open and continuing to ship packages. Learn about our response to COVID-19

Popular Amana Dryer Hardware

Your Price
$7.65
Roller Support Tri-Ring
PartSelect Number PS11755850
Manufacturer Part Number WPW10512946
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pulley shaft, or on the rear drum roller shaft. In either case, you will need to remove the front panel of the dryer and the drum to access the part for repair. Once you have accessed the damaged tri ring, you will simply need to slip it off and replace it with the new one. This part is sold individually. Be sure to disconnect the power source from the dryer before you begin this repair.
Fixes these symptoms
Noisy
Will not tumble


Installation Instructions
John from Tucson, AZ says,

worn out part
The repair was fairly easy. The most timely part of the repair was removing the twelve screws from the back panel to expose the repair....read more

Your Price
$41.24
Igniter Kit
PartSelect Number PS334180
Manufacturer Part Number 279311
If your dryer will not heat, takes too long to dry, or does not provide enough heat, you might want to replace your igniter kit. This silicone carbide igniter with ceramic holder kit includes the 3-inch flat igniter, bracket, 4-inch wire leads, and the plug. The kit can replace both round and flat igniters and is used for many gas clothes dryers. Be sure to disconnect the power source from your dryer before you do this repair. The igniter is located within the burner assembly, so you will require tools to complete the repair. You will need a putty knife, a small flat blade screwdriver, a 5/16 nut driver, and a 5/16 socket with a ratchet.
Fixes these symptoms
No heat or not enough heat
Takes too long to dry
Will Not Start

See more...
Installation Instructions
TEODY from MILPITAS, CA says,

No Heat. Dryer keeps running but no heat to dry clothes.
Repair was very easy. We are in the internet age so I use it all the time to get info on how to repair any thing in the house including cars. This time it was my dryer. I typed up 'Kitchen Aid dryer h...read more

Your Price
$5.69
Thrust Washer
PartSelect Number PS11740482
Manufacturer Part Number WP233520
This genuine OEM washer has a 3/4 inch outside diameter. This thrust washer can be used on most makes and models of dryers. A complete list of compatible dryers is available below. The washer is found on dryers around the drum support rollers and idler pulleys, and helps prevent the rollers and pulleys from bumping up against the brackets they are installed on. Your thrust washer could be defective if you notice your dryer wont tumble, rotate, or turn; or there is a load squealing or whining noise when the dryer tumbles. The repair is a relatively easy job. You will require a putty knife, 5/16 inch nut driver, and E-Ring pliers. Remember to disconnect the power to your dryer before you begin the repair.
Fixes these symptoms
Burning smell
Noisy
Pumps but will not spin

See more...
Installation Instructions
Chris from Hopedale, MA says,

Drum not centered , clothes getting stuck in dryer
The first thing I did was to unplug the dryer from the wall. Then I removed the bottom two screws and slid the bottom cover off so i could see all the way to the back, I tipped the dryer back against...read more

Your Price
$7.48
Drum Roller Shaft Washer
PartSelect Number PS11740748
Manufacturer Part Number WP312535
If you notice that your dryer is noisy or will not tumble, then you may need to replace the drum roller shaft washer. This drum roller shaft washer is just under an inch in diameter and is sold individually. It is located on the shaft of the drum roller, in the interior of your dryer. To access the drum roller shaft, you will need to remove the front panel of your dryer, and then remove the drum. Before completing this repair, be sure to disconnect the power source from the dryer. Tools required for this repair include a 5/16 nut driver, a stubby Phillips screwdriver, and a pair of snap ring pliers.
Fixes these symptoms
Noisy
Will not tumble


Installation Instructions
gerald from park city, MT says,

dryer squeeking
removed front panel,lifted top, removed drum and drive belt,remove old rollers and acc and instlled new and reinstalled dryer parts....read more

Your Price
$3.60
Screw - 10-16 x 1
PartSelect Number PS11741409
Manufacturer Part Number WP3387230
This screw is sold individually.
Fixes these symptoms
No Symptoms for this part
Installation Instructions
Sean from ROCK HILL, SC says,

Part broken in half
Remove screws, dryer sensor on screen. Put sensor back in place. Secure with screws. The way you take it off go in reverse....read more

Your Price
$3.89
Cover Screw
PartSelect Number PS11740701
Manufacturer Part Number WP308685
Sold individually.
Fixes these symptoms
No Symptoms for this part
Installation Instructions
Peter from WRENTHAM, MA says,

Kenmore 80 Series Washer - Agitator Stopped Working
First I screamed at the ceiling, because I have a three year old and an infant, and the washing machine was dead. Then I went to youtube. It seemed like the "agitator dogs" were the issue.

read more

Your Price
$9.94
Single Front Panel Cip
PartSelect Number PS11731288
Manufacturer Part Number W10854425
This part is the replacement single front panel clip for your dryer. It is made of metal and is approximately 2 inches long and ¾ inch wide. The front panel retainer clip is what holds the front panel on to the dryer. If the clip is damaged or missing, or if the front panel appears loose, you may need to replace the clip. This part is sold individually and is an authentic OEM part.
Fixes these symptoms
Noisy


Installation Instructions
Sean from BAR NUNN, WY says,

Belt was slipping, and having a hard time spinning the drum
First off, start by turning of the breaker to the dryer and confirming the power has been turned off. Next, remove the lint screen and two screws holding the lint screen housing to the lid. Remove the...read more

Your Price
$3.42
Hose Clamp
PartSelect Number PS11743008
Manufacturer Part Number WP596669
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This clamp is used to securely attach a hose to another part of your appliance, which helps prevent leaks from those connections. Depending on the appliance, it can attach hoses to drain pumps, water inlet valves, pressure switches, and injector nozzles. We recommend you refer to model-specific diagrams for appropriate uses and exact placement. This hose clamp is made of metal, and is sold individually. To access and replace this part you will need a nut driver, pliers, and screwdrivers. Before you begin any repair work, make sure you have unplugged your appliance, and shut off the water supply if applicable.
Fixes these symptoms
Leaking
Will not stop filling with water


Installation Instructions
jeff from lindenhurst, IL says,

Washing Machine was leaking water
Loosened the hose clamp, removed the injector valve and injector nozzle assembly, replaced both and tightened with new hose clamp. Fixed the problem for less than $20!! Washing machine is 20 years o...read more

Your Price
$6.69
Single Access Panel Spring Retainer/Clip
PartSelect Number PS11741425
Manufacturer Part Number WP3388229
Sold Individually.
Fixes these symptoms
Door won’t close


Installation Instructions
Russell from Orlando, FL says,

Dryer would not heat.
Watched on-line video on how to disassemble and test heater element, thermostat, and hi-temp shut down. Heater element was open. Ordered new heater element. Re-installed heater element iaw video pro...read more

Your Price
$7.65
Retaining Ring
PartSelect Number PS11740487
Manufacturer Part Number WP23748
The metal retaining ring, which is under an inch long, holds the rear wheels on the axels of the dryer. The main reason why it would need to replaced is if the retaining ring has sprung out of place or is damaged. Some the symptoms could be that your dryer does not tumble, it makes a loud buzzing noise, or if it pumps, but will not spin. The tools needed for this project are a putty knife, 5/16 nut driver, and snap ring pliers. Refer to the installation video and diagram for further instructions and guidance. Customers ranked this replacement project as easy.
Fixes these symptoms
Burning smell
Noisy
Pumps but will not spin

See more...
Installation Instructions
David from Underwood, IA says,

Loud banging sound. Worn out roller.
Pulled off the lower panel with 5/16 socket.Pulled off the door assembly by removing the two screws at the bottom of the door assembly. I pulled down a little and then out. be carefull of the wires. O...read more