Amana Dryer Valves

Amana Appliance Parts
Shop By Part Type

Popular Amana Dryer Valves

Your Price
  In Stock
M Series New Style Coil Kit
PartSelect Number PS334310
Manufacturer Part Number 279834
When the igniter reaches a high enough temperature, these coils (Coil Valve, Dryer Gas Valve Coil Kit, Dryer Valve Coil Kit, Gas Valve Solenoid) work together to open the gas valve and allow the gas to enter the burner. This is a safety mechanism to ensure that there are no unsafe buildups of gas inside your appliance. The coils are attached to the dryer gas valve. If the dryer does not heat or heats intermittently, the coil may not be opening the gas valve. Both coils must be operational for the valve to open. No continuity would indicate a defective coil, but they can be intermittent and fail when they get hot. Both coils should be replaced when one of them is broken. This part can break as a result of material fatigue from normal use. This part measures approximately 1 inch in diameter and 1 inch in height, and is constructed of plastic and metal. It comes in black/beige. This part features a 3-terminal boost/hold coil and a 2-terminal secondary coil
Fixes these symptoms
  • No heat or not enough heat
  • Noisy
  • Shuts off too soon
  • See more...
Installation Instructions
Michael from Kirkwood, MO
Gas Dryer would not ignite
1. Removed lint screen and holder frame. Unplugged the electrical cord and closed the gas valve in the line before it goes into the dryer.
2. Removed two bolts at bottom front of machine and took off the bottom front panel.
3. Removed three bolts from black plastic exit vent and took it out to give more room to access everything.
4. removed two wires and screws on the limit thermostat. Did the reverse to place the new one.
5. Removed wires (remembering placement), then holder screw. rotated the Gas Dryer Sensor counter clockwise to release the bottom tab so the sensor can be taken off the flame tube. Did the reverse to place the new one on.
6. Removed the one screw on the gas/flame tube that holds the bracket and igniter inside the flame tube. Removed the wires fro the igniter (remember placement) Slid the whole assembly toward the back of the machine to get the tube off the gas valve then rotated the whole assembly counter-clocwise to release the tab on the left side of the bracket. This was a little tight and had to work with it a bit to get the tab out and slide the whole piece out of the flame tube.
7. Once the tube and igniter were out i removed the scree that holds the igniter and replaced with the new one. Made sure no dust, etc. was in the piece.
8. Did the reverse to place the tube/igniter back into the flame tube.
9. Carefully and forcefully removed the wire connectors to the two coils. These were tough to get off. Removed the two screws that hold the bracket that holds the two coils in place. Slid the coils off the spindles remembering which one has the two wire connection and which one has the three wire connection and the way they went on. Replaced the old with the new. Placed the bracket onto the new coils and made sure the little bumps on the top are in the holes in the bracket. Tightened the screws to hold the coil bracket. Reattached the wire connectors to the coils making sure they go ALL the way back on.
10. Vaccumed everything I could to get lint, dust, etc. out.
11.Replaced the black vent plastic.
12 Made sure the exit vent on the back was not crimped or clogged. Checked the little flap door where the vent goes outside to make sure it opens and closes super easy to no air flow is restricted.
13. For testing I left the bottom panel open. Make sure you closed the door, reconnect the plug and turn the gas valve back on. Hit the go button on autodry or timed dry. The door must be closed to create the closed circulation of the system so the fan sucks the flame into the tube otherwise the flame will not fire deep into the tube and will set off one fo the overheat sensors. After hitting the go button your drum will start to rotate, then a few seconds later you'll hear a click and your igniter will start to burn bright orange. Another click and the gas should flow and ignite.
14. This shows that you've fixed the ignition problem. I just replaced everything I thought that could be wrong in stead of hunting and trial and error. All the parts were about $137 so I thought it was worth making sure.
15. IMPORTANT: If during your test the flame turns off after a little while then turns back on only to turn off again, don't panic. This happened to me as well. I found that you need to run the dryer with wet clothes in the dryer. The wetness in the clothes will keep the autodry sensor from shutting off the dryer since there will be moisture in the exhaust. If it's on timed dry the wet clothes will cool the exhaust air and keep the overheat sensors from turning the heat off. So no heating of dry clothes to get out wrinkles. Just dry the wet clothes. This is all I did and it's been working great so far. Good Luck!
Your Price
  On Order
Liquid Propane Conversion Kit
PartSelect Number PS8691743
Manufacturer Part Number W10606694A
This gas conversion kit is used to convert natural gas burners to liquid propane in dryers. If your dryer will not start, heat, or there is an unusual smell, replacing this part can be a solution to the problem. The tools needed for this repair project are: a putty knife, 5/16 inch nut driver, small flathead screwdriver, pliers, and a 3/8 inch wrench. As a safety precaution remember to unplug your dryer from the power source before beginning this installation project. Refer to the manual provided by the manufacturer for further installation instructions and a detailed diagram.
Installation Instructions
Robert from Tenino, WA
converting to LP gas
First I removed the front panel which allowed access to the burner assembly. Then I removed the gas connector and elbow from the back of the dryer. Then I removed 2 screws that hold burner assembly in place and 2 screws that hold an angle brace for the burner assembly. Had to loosen the screw that clamps around the gas pipe holding it in place clear in the back inside dryer housing. Unplugged all wiring connectors, then I removed the burner assembly and removed the 2 screws holding the burner tube to the valve. Remove the orifice and replaced with the proper size for LP gas. Then removed the blocking pin and replaced with one for LP gas. Then reassembled in reverse order. Actually pretty easy. Read more...
Your Price
  In Stock
Liquid Propane Conversion Kit
PartSelect Number PS3493998
Manufacturer Part Number 49572A
This part converts your appliance from Natural Gas to Liquid Propane.
Installation Instructions
Billy from Maryville, TN
cocverting natural gas to propane gas
removed burner installed propane orfice and kit as per instruction sheet. Read more...
Your Price
  In Stock
Gas Dryer Conversion Kit - NG to LP
PartSelect Number PS1943997
Manufacturer Part Number MAL9000AXX
This conversion kit contains all parts needed to convert your gas dryer from natural gas (NG) to liquid propane (LP). This kit will work with some Samsung dryers as well. Use model # to ensure you are getting the correct part.
Installation Instructions
Timothy from Lawson, MO
Brand new dryer...needed to convert to propane.
I followed the directions that came with the conversion kit; which I ordered from PartSelect. Your website was the only place that could help me. Our new dryer is actually a Samsung. The people at Best Buy were no help. I called the Samsung headquarters and a "real" person there told me I could order from them or use a Whirlpool kit because they are the same. You guys were faster in getting me one, so I went with you. My wife was happy. I would recommend you to others. Read more...
Your Price
  In Stock
Natural Gas Orifice for Dryer Gas Valve
PartSelect Number PS11740485
Manufacturer Part Number WP234826
Installation Instructions
Dexter from COUNCIL BLFS, IA
Needed to convert from LPG to Natural Gas
Two parts were needed in order to convert the dry back to Natural Gas. Part Select is usually good, but dropped the ball completely on this one. I received the correct Orifice, but was not asked or told about the need for the part for the regulator so the gas pressure would be changed back to Natural Gas. I found one at a local supplier and finished the switch. I chose to change the belt while in there because the dryer sounded like the belt had a chunk missing with the rhythmic thump. After installing the new, I found that one of the tumble paddles had a penny flopping inside it. One thump per revolution. This is the first in my career that the technician had not left the original orifice and regulator cap attached to the dryer. Read more...
Your Price
  In Stock
Liquid Propane to Natural Gas Conversion Kit
PartSelect Number PS11741137
Manufacturer Part Number WP33002924
This kit converts liquid propane to natural gas.
Your Price
  In Stock
Gas Valve Kit
PartSelect Number PS334359
Manufacturer Part Number 279923
This gas valve kit comes with the wiring harness.
Fixes these symptoms
Your Price
  In Stock
Natural Gas Limiter
PartSelect Number PS11743791
Manufacturer Part Number WP694424
The leak limiter or natural gas limiter is used in dryers. This part acts as a cover of the adjustment screw on the pressure regulator. If you are changing from propane (LP) back to natural gas, it is best to replace this part. To convert your washer from LP to natural gas, remove the top of the dryer and screws to access the computer. When control panel is accessed, remove the wire harnesses in the front and the control panel itself. Next, remove the access panel and disconnect the wire that activates the moisture sensor. Remove the main front panel using a 1/4 inch nut driver and the belt from the pulley. Once you pull out the drummer you now have access to the gas valve. Refer to the diagram for further installation instructions. Remember to unplug your dryer from the power source for safety.
Your Price
  In Stock
Orifice, Burner (Type 4 (Propa
PartSelect Number PS11740486
Manufacturer Part Number WP234868
Sold individually.
Your Price
  In Stock
Orifice, Burner (Type 1)
PartSelect Number PS11738696
Manufacturer Part Number WP15418

Related Parts