Whirlpool Microwave Hardware

Whirlpool Appliance Parts
Shop By Part Type

Popular Whirlpool Microwave Hardware

Your Price
$8.12
  In Stock
Top Mounting Screw
★★★★★
★★★★★
(2)
PartSelect Number PS11744892
Manufacturer Part Number WP8169704
This screw is sold individually.
Installation Instructions
Michelle from Gilbert, AZ
Bought Used needed Top Mount Screws and Filters
Awesome! Everything fit and worked! Thanks! Read more...
Your Price
$7.76
  In Stock
Screw
PartSelect Number PS11743743
Manufacturer Part Number WP681249
Sold individually.
Your Price
$7.76
  In Stock
Cover Screw
PartSelect Number PS11740701
Manufacturer Part Number WP308685
Sold individually.
Installation Instructions
Curtis from PALM BAY, FL
Relocating dishwasher into the new kitchen layout
In this case the dishwasher had already been installed for a few years. After removing it, we inspected it and saw it needed a bit of TLC. The transport wheels on the back were missing, making it harder to move around without scratching the tile and some of the original hardware was rusted or broken off. I looked up the parts easily here on PartsSelect using their parts breakdown diagrams and was glad to see what I needed was still available. We had a licensed plumber relocate the hot water line and drain for us to make things a bit easier.
A licensed electrician had also moved the power line over to the new location and left a wire sticking out of the bottom of the wall to hardwire the dishwasher in again. We decided to convert the dishwasher to be able to be plugged into a standard 20amp wall outlet instead. We had already purchased a kit with a nice long cord and strain-relief snap on plastic fitting that snapped onto the metal incoming power box on the bottom front of the dishwasher. Using the supplied wire nuts, etc., we connected the wires and ground wire to the proper wires from the dishwasher and ground lug. We put the dishwasher aside and then went to work on converting the power wire coming out of the bottom of the wall, to a conventional outlet. I am mentioning all this because in our first attempt we unfortunately put the receptacle a bit high off the floor and the new power cord plug end, stuck out and hit the back of the dishwasher so it would not go all the way in and was sticking out from under the counter top. I tried using one of those flat adapter cables, but even that still stuck out to far. So we ended up relocating the outlet box as low as we could on the wall and this allowed the plug to stick out into the opening area at the bottom rear area of the dishwasher so it could now be slid all the way in under the kitchen counter properly. I hope that bit of trial and error will save you some time if you ever decide to go the pluggable route too.
The new installation required the use of the dishwasher side mount brackets, so we had to purchase a replacement set of those, complete with the hardware to screw them down.

This project took a bit longer than planned due to the power plug problem, one which we will remember for any other similar appliance relocation projects, as well as the time to get our new parts in that we had to order, but other than that the rest went smoothly and the dishwasher was relocated successfully.
Read more...
Your Price
$7.76
  In Stock
Screw, 8/18 x 3/8
★★★★★
★★★★★
(2)
PartSelect Number PS11746840
Manufacturer Part Number WP90767
This screw is sold individually.
Installation Instructions
Alexander from Lakeland, FL
Broken Dryer Knob
First let me just say that Partselect.com is now one my stored favorites in my web browser. I came home from a business trip and saw a pair of pliers on the dryer. I thought that was odd until my wife informed me that the knob on the dryer had broken. So she was using the pliers to select the cycle. Somehow she knew where the missing pointer was actually pointing. Since the dryer was over 5 years old I saw this as an opportunity to upgrade both appliances. Not with my frugal wife. A search of the Internet popped up partselect. I ordered Wednesday morning and the parts where on my doorstep late Thursday. Trust me I was very surprised. Everything worked perfectly. Two thumbs up!!! Read more...
Your Price
$8.12
  In Stock
SCREW
★★★★★
★★★★★
(2)
PartSelect Number PS11728054
Manufacturer Part Number W10841091
Sold individually.
Installation Instructions
Richard from PRINCETON JCT, NJ
Door Handle failed (cracked at mount)
KitchenAid Microwave [Model: KHMS 145 JBS-0]Door Handle Repair
Tools and Parts
• Door Handle [Part # PS390101]
• Putty Knife
• Phillips Screwdriver
• Tray (cup) for parts during disassembly/reassembly (3 screws on door; 2 screws on handle; spacer on top-door edge).
Instructions
• Preparation
o Disassembly can be managed with the door mounted on the unit. The handle is attached by 2-screws that can be accessed only by separating the outer/inner door panels.
o Before starting the project, watch the Youtube.com video for a GE Microwave, which is the most applicable video for removing the collar [i.e., plastic bezel around the viewing window on the inner door) and for separating the outer/inner door panels ].

• Remove the collar
Photo 1: Inner-side clip (bottom of collar) used on
3-sides of the collar (top edge is a spacer) Photo 2: Hinge side clip (right edge)

o As indicated in the video, small clips are on the inner-side of the collar on 3-sides (top, bottom, and open-door edge).
o The clips are on the outside of the collar for the door-hinge side.
o These clips are small and somewhat fragile – once a few are popped, finger pressure will generally pop the remaining clips.


• Separate the outer/inner door panels

Photo shows the inner/outer doors separated, and the 3-screws removed.
o Remove the 3-screws on the door edge before separating the outer door panel.
o There is a plastic spacer on the top, outside edge of the door that is not cemented. Remove the spacer after separating the door panels.
o Use a putty knife to pop the clips for the outer-door panel around the top, bottom, and open-door sides.
o The top door corner (the spacer edge) is tight and should be gently pushed back.
o The outer door panel will remain attached on the hinged edge and function like a second door – move gently.
o The viewing glass is clamped in place; but, handle with caution.

• Remove the Door Handle
o With the outer/inner panels separated, remove the two screws holding the handle and remove the handle.
o Retain the screws for later use.

• Install the new Door Handle
o Reuse the original screws (Note, [Part # W10841091 – screw] is a different thread, and is not self-tapping)
o The door-handle screw holes are not tapped; so insert the old screws in the handle to tap before installing the handle, leaving approximately 1/8 - 3/16” exposed.
o Remove the screws and reuse to install the handle.


Comparison of 2-original screws vs. replacement screw (note thread gauge differences).
• Reinstall the Outer Door Panel
o Align the spacer with the inner-panel edge in the upper corner.
o Close the outer panel, gently snapping the clips into place.
o Reinstall the 3-screws on the door edge.

• Reinstall the Collar
o Snap the hinge side in place.
o Gently snap the remaining sides in place
Read more...
Your Price
$7.76
  In Stock
Screw
★★★★★
★★★★★
(1)
PartSelect Number PS11742721
Manufacturer Part Number WP488729
Metallic screw that is less than an inch long. Does not include the plastic washer.
Installation Instructions
Kyle from Wimauma, FL
Black Cam was bren on lower door hinge
This was a very simple job. Remove the top Hinge bracket, a total of 4 screws, lifted the door off the bottom hinge, removed the bottom hinge set up, 2 screws, replaced it, and attached the new bottom black door cam, lifted the door back onto the bottom hinge and aligned the top hinge, and reinserted the screws, and Ta Da, The door works like a new refrigerator door. 15 to 30 min tops. I did not even have to take the refrigerator items out of there door holder. Read more...
Your Price
$7.76
  In Stock
Screw
PartSelect Number PS11742539
Manufacturer Part Number WP4449154
Sold individually.
Installation Instructions
Dan from Madison, MS
Bake Unit not heating properly
Turned the power to the oven off. Took two crews out. Disconnected the old unit, connected the new unit, put the two screws back in and tested the unit. Read more...
Your Price
$8.12
  In Stock
Nut
PartSelect Number PS8260221
Manufacturer Part Number W10596040
Your Price
$7.76
  In Stock
Screw
★★★★★
★★★★★
(1)
PartSelect Number PS11743744
Manufacturer Part Number WP681414
This screw is sold individually.
Installation Instructions
Pamelia from LA CROSSE, VA
Our washer was purchased 1/6/2006 and it started banging and walking out of its place when the washer started into the spin cycle. This would occur no matter the size of the load.
We followed the instructions show on the video. However, our model was assembled slightly different. We had to remove the screws from both sides of the side panels so that we could remove the tub from inside of the machine. Also our model only has one belt not two.
Over all it was easy considering my husband and I had never attempted to repair a washer. Once we got it back together it when back to working like it had never been broken!
We would have never been able to repair our washer without the video that your site provided... thanks so much!!??

Sure wish the manufactures would consider making the older models again as lots of us are not happy with the new modules being manufactured presently!
Read more...
Your Price
$7.76
  In Stock
Screw
★★★★★
★★★★★
(1)
PartSelect Number PS11741601
Manufacturer Part Number WP3400805
Sold individually.
Installation Instructions
joan from arlington heights, IL
Door handle broken
Couldn't have been easier. Unscrewed old handle and screwed in the new. I ordered new screws but didn't need them, just used the old ones. Read more...

Related Parts