Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This splutch cam kit is a genuine replacement assembly designed for select Whirlpool, Maytag, and affiliated brand washing machines. It plays a critical role in the wash and spin cycles by engaging th...
This genuine OEM drive belt is designed to transfer power from the motor to the drum in select Whirlpool, Maytag, Kenmore, and other compatible washing machines. Operating at 115 volts and 60 Hz, the ...
This is lid lock designed for use within various washing machines. This lid lock, also known as a latch assembly, is used to secure the lid of your washing machine during the washing cycle. If your wa...
This suspension rod kit includes four rods designed to stabilize the wash tub in compatible top-load washing machines. By minimizing vibrations and excessive movement during wash and spin cycles, thes...
This 6-pin shift actuator is an authentic OEM part supplied directly by the manufacturer for use in washing machines. The shift actuator is responsible for controlling the movement of the washer trans...
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
This washing machine cleaner includes three time-release tablets designed to remove odor-causing residues, grime, and buildup from high-efficiency and top-load washing machines. The tablets work by cl...
This is a lid strike for various models of top-load washing machines. Lid strikes are designed to engage with the lid switch and communicate to the control board that the washer can start. If your was...
$21.45
In Stock
Order now and your part arrives by May 9
Questions And Answers for NTW4605EW0
Ask our experts a question about this model and we'll get back to you as soon as possible!
48 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Tony
January 27, 2020
I have a piece of a necklace sticking out from under the agitator, How do I lift the agitator out so as to remove this?
For model number NTW4605EW0
Hi Tony,
Thank you for your question. To remove the agitator, you will first need to remove the dispenser cap on the top of the agitator and expose the bolt underneath. Then you will just need to remove the bolt and then pull up on the agitator to remove it. We hope this helps. Thank you and have a great day.
12 people found this helpful.
Did this question help you?
Thank you for voting!
Debbie
February 23, 2020
Washer won't start. No power comes on but there is power to the outlet that it is plugged in to.
For model number NTW4605EW0
Hello, Thank you for your question. You will want to check into the door latch and the knobs that you use to operate the machine. The lock will not allow the unit to start is there is a short or it is not reading the door is closed. That is part#PS12704713. We hope this helps, good luck with this repair.
7 people found this helpful.
Did this question help you?
Thank you for voting!
Brian
March 2, 2020
I just replaced the lid lock on my washer. Now that that is in it wont fill lid lock light wont come on. Do i have to unlock them when there new?
For model number NTW4605EW0
Hello Brian, thank you for your question. Yes, It is possible that the latch was engaged in the lock position and not allowing the strike to enter the latch assembly. If you disconnect the lock from the control while the unit is turned off, you can test the lock to see if it is in the locked state. If you test the blue wire to the white wire for resistance, if it reads 0 ohms then it is in the locked state. If it reads infinite, then the lock is in the open position. This will help to identify if the lock is in the locked position. If it is in the locked position contact customer service to return the part and a new latch should be ordered. I hope this helps.
4 people found this helpful.
Did this question help you?
Thank you for voting!
Lalo
December 23, 2019
6 year old Amana marking loud ratcheting sound .I replaced the worn cam and actuator , still having same problem. What else should i be looking for to replace .
For model number NTW4605EW0
Hello Lalo and thank you for writing.
It certainly sounds like a faulty pulley PS10057144 and/or belt PS11747978 you should check for signs of damage, and replace it if needed. We hope this helps. Please contact us anytime.
Machine is going off balance but not every load. Could it be something under the drum or the springs and does the lid pop up.
For model number NTW4605EW0
Hello Becky, Thank you for the question. I suggest checking the Suspension Rod Kit, PartSelect Number PS11703288 for wear or damage. We hope this helps!
Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch
... Read moreand put aside, so you can snap off the cover for drive clutch on upper part with screwdriver and off the parts come and install whole unit back as took it apart. Line up the new upper clutch so that is position as was before. (Using parts diagram helps a lot as www. partsselect.com has for you or Maytag.com.) Then put the electronic part board back on and the gear and nut. Make sure it is tight by several attempts to make sure it's snugged up good and then slowly roll belt back on the pulley and motor drive. Put your cover guard back on with two screws and done.
Replaced the 4 suspension rods/springs. Only disconnect and replace one at a time. The tub will fall out if you disconnect and replace more than one rod/spring at a time.
