Maytag Range Fuses

Your Price

$5.45

Maytag Range Ceramic Fuse - 20 Amp

★★★★★

3 Reviews

PartSelect Number PS11747931

Manufacturer Part Number WPM0805101

This microwave fuse is just over an inch in length. It has a white ceramic center, and metal on either end. This is a twenty amp 250-volt fuse, and is used to power your microwave. If your microwave will not heat properly, will not turn on, or the touch pad becomes unresponsive, there could be a faulty fuse which should be replaced. Remember, since this part contains an electrical charge, before you replace the fuse from your microwave, make sure that the power is disconnected from the unit. This part is sold individually. NOTE: Make sure your microwave is unplugged, and your capacitor is discharged before you begin this repair. A capacitor stores large amounts of electricity even after your microwave is unplugged.

Fixes these symptoms

Won’t turn on
See more...

Installation Instructions

Jay from Edwardsville, IL

Blows main fuse when the microwave generator start, (cooking function).

Remove microwave from oven cabinet. remove cover and check main fuse with ohm meter.
Tried fuse, it does not blow untill cooking starts.
Check capacitor with ohm meter, after properly performing capacitor dischagre procedure.
Order new capacitor, simple installation. another new fuse and all is good and cooking again. Read more...

Your Price

$86.93

Maytag Range Thermal Fuse

PartSelect Number PS11752972

Manufacturer Part Number WPW10328492

This thermal fuse is a critical safety component designed to cut power to the heating element if temperatures exceed safe limits, preventing overheating and reducing the risk of fire. It works by breaking the electrical circuit when excessive heat is detected, protecting the appliance from damage. A blown fuse can cause the range or oven to stop heating entirely. This is a single-use device and must be replaced once it fails. For safety, always unplug the appliance or shut off the circuit breaker before installation.

Your Price

$15.00

Maytag Range Fuse

PartSelect Number PS12348785

Manufacturer Part Number W11188752

Your Price

$98.10

Maytag Range Thermal Fuse

PartSelect Number PS11742553

Manufacturer Part Number WP4450249

Installation Instructions

Christy from Paso Robles, CA

After using the "self-clean" option, the panel blew out and the door remained locked. We knew we burnt fuses but didn't know which ones. We had a technician come out and tell us which ones. ($70.00) He quoted us a price of $495.00 for parts and labor. We did the repair ourselves and cost us $157

The hardest part was getting the oven out. The double oven is pretty heavy.

The screws were on the sides under a removable strip. Have a table about the same height as the base of the oven. It was easy to slide it straight over to the table.

The schematics are on top of the oven. Although you probably won't need them for the parts we replaced. When you have the oven out and the back panel removed, it is easy to identify the exact parts you are replacing. The part numbers were the same on the fuses. The thermostat was a simple pull apart. Then undo the 2 screws inside the oven. The heat sensor required some figuring. There is a pin that holds it in place in a plastic casing. We used a small flat head screw driver to push the pin flat to loosen it from the casing. This part was behind the digital panel and the only one that didn't require the oven coming out.

We would easily do this project again and glad we did. We saved $340.00 by doing it ourselves. I am glad I found PartSelect.com

Make sure you turn off the breaker to the appliance first. You don't want any electrical surprises. The hospital bill would be more expensive than the repairman !! Read more...

Your Price

$50.56

Maytag Range Use Wpl 74010080

PartSelect Number PS2366079

Manufacturer Part Number 7733P424-60

Your Price

$49.50

Maytag Range Fuse Block

PartSelect Number PS2350379

Manufacturer Part Number W10245194

Your Price

$17.15

Maytag Range Fuse

PartSelect Number PS11747999

Manufacturer Part Number WPW10017410

This microwave time delay fuse is a 20-amp safety component designed to protect the appliance from damage caused by power surges. If your microwave fails to start, a blown fuse may be the reason. Replacing it can help restore safe and reliable operation. Compatible with a wide range of models, this fuse is built to meet the performance needs of many household appliances. Before installation, disconnect the microwave from its power source and wear protective gloves to ensure safety.