Maytag Range Sensors
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Maytag Range Sensors
Your Price
$75.13
In Stock
Maytag Range Oven Sensor
The sensor that has been replaced is not what is expected. After reading all of the instructions for adjusting the temperatures, the only temp that stays steady is when we first turn on the oven to 350 degrees. That stays steady but when I turn it to 400 it slowly goes up to 425 degrees. Read more...
PartSelect Number PS11749737
Manufacturer Part Number WPW10181986
This oven temperature sensor, for ranges, works together with the oven control board to measure and regulate the oven temperature. The sensor detects the temperature in the oven cavity. If the following symptoms occur, replacing the temperature sensor could be the solution: Little or no heat when baking, oven not heating evenly, oven will not start, and/or oven is overheating. Often, if the sensor is defective, the oven temperature will fluctuate and be inaccurate by more than 50 degrees. The tool needed for this replacement is a #2 square head screwdriver or a #2 Philips screwdriver. Remember to unplug the range before installing the part.
Fixes these symptoms
- Element will not heat
- Little to no heat when baking
- Little to no heat when broiling
- See more...
Installation Instructions
Ruth from Oregon, IL
temperature not accurate after 3 1/2 years of happy usage
Opened up the back of the stove. Unpluged the sensor. Replaced the sensor. Replace the back of the stove.The sensor that has been replaced is not what is expected. After reading all of the instructions for adjusting the temperatures, the only temp that stays steady is when we first turn on the oven to 350 degrees. That stays steady but when I turn it to 400 it slowly goes up to 425 degrees. Read more...
Your Price
$59.47
In Stock
Maytag Range Temperature Sensor
PartSelect Number PS820208
Manufacturer Part Number 316217002
The oven temperature sensor for your range may also be called a probe. The quick connect on this part may differ than your original piece. If the temperature sensor does not fit you will have to cut off the quick connect, and then wire together with porcelain wire nuts. The function of the oven temperature sensor is to measure the temperature in the oven and signal the other heating components. Before you begin this repair make sure to disconnect the power to the range. The tools required for this installation include a number two Phillips screwdriver or a number two square head screwdriver, and maybe a pair of wire strippers and crimpers.
Fixes these symptoms
- Element will not heat
- Little to no heat when baking
- Little to no heat when broiling
- See more...
Installation Instructions
Dan from Bellevue, ID
Oven not heating to desired temperature
Replaced clock control by removing surface burner control knobs and plastic nuts, and then the cover over the oven control. Two screw hold the clock in place, after removal and disconnecting the plug-in you can reinstall the new clock control. The Heat Sensor inside the oven will also need to be replaced. It is located inside the oven and attached with two screws; the back of the oven will need to be removed to unplug. Reverse removal procedure and turn the power back on to the stove.
Read more...
Your Price
$43.18
In Stock
Maytag Range Long Oven Sensor
PartSelect Number PS1570174
Manufacturer Part Number 12001656
This long oven sensor is also commonly known as a temperature sensor. It is designed for use with ovens and ranges. It is similar to a thermostat; it measures and regulates the internal temperature of your oven cavity. There is an adapter at one end, a probe at the other, and they are connected by an insulated wire. The probe is approximately 7 inches long. You can test the sensor with a multi-meter for functionality. You need to check the model-specific manual to determine what the proper resistance is for your specific appliance. This oven sensor comes with two wire harness adapters and a set of instructions.
Fixes these symptoms
- Door won’t open after self cleaning cycle
- Element will not heat
- Little to no heat when baking
- See more...
Installation Instructions
David from Westford, MA
Oven not holding 350 F, when cooling the coils did not reheat
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. The oven works fine! Note that due to thermal lag the temperature overshoots to 370 degrees and undershoots to 340 degrees, this appears to be normal oven operation. Putting door back in place was easy.
Read more...
Your Price
$103.46
In Stock
Maytag Range Sensor
PartSelect Number PS11726314
Manufacturer Part Number W10833885
This is a manufacturer-made oven temperature sensor for various models of range. This sensor is designed to accurately detect the internal temperature of your oven and communicate with the control board to control the level of heat inside of it. Over time and through extended exposure to hot temperatures, this sensor can fail and cause your oven to have issues heating or staying at a consistent heat level, at which point it needs to be replaced. This sensor features a wire harness to connect to the control board of the oven, as well as two mounting screws to install it. Replacing this sensor is easy and only requires a screwdriver to unthread it from the lower portion of your oven. This sensor is sold on its own, and does not come with any other necessary parts, like its securing screws.
Fixes these symptoms
- Element will not heat
- Little to no heat when baking
- Oven is too hot
- See more...
Installation Instructions
Andrew from BOTHELL, WA
Oven would heat up very slowly and not reach more than 325 *F
I purchased all the likely suspects. It was a corroded lower heating element that was faulty. Fixed the burnt out light bulb for good measure while I was in there.
Read more...
Your Price
$35.80
In Stock
Maytag Range Short Oven Sensor Kit
Replacing the oven sensor was very easy. I removed the back panels 6 screws to gain access to the sensor's connection. I then removed the 2 screw that hold the sensor in place inside the oven and pulled the old sensor out through the oven. I reversed this process to place the new sensor in the oven. Read more...
PartSelect Number PS2003225
Manufacturer Part Number 12001655
The temperature sensor on your oven detects the temperature within the oven cavity. If you notice your oven is too hot, not hot enough, or does not heat evenly, the short oven sensor kit may need replacing. This oven sensor is referred to as the short sensor and is 3 inches long. It should not be confused with the 6-inch-long sensor. The oven sensor is located on the back wall of the interior of the oven. Before starting this repair, be sure to disconnect the power source from the oven. If you are repairing a gas range, make sure to disconnect the gas source as well.
Fixes these symptoms
- Element will not heat
- Gas igniter glows, but will not light
- Little to no heat when baking
- See more...
Installation Instructions
george from birmingham, AL
F1 code - gas over would not heat.
Repair tech checked oven and said the control panel was bad and needed to be replaced. The new control panel would cost over $450.00! I found that the oven sensor was bad and replaced it for $30.00. The old oven sensor had failed following a self cleaning cycle. I found that the wires coming out of it were burnt.Replacing the oven sensor was very easy. I removed the back panels 6 screws to gain access to the sensor's connection. I then removed the 2 screw that hold the sensor in place inside the oven and pulled the old sensor out through the oven. I reversed this process to place the new sensor in the oven. Read more...
Your Price
$76.17
In Stock
Maytag Range Temperature Probe
PartSelect Number PS11747165
Manufacturer Part Number WP9755542
Also known as a meat probe.
Fixes these symptoms
- Will not program
- Will Not Start
- See more...
Installation Instructions
Kent from Seattle, WA
faulty meat probe
Not a repair. Just needed to replace the meat probe sensor for the programmable oven. Quick and easy purchase and very fast delivery took care of the problem. I was back in business.
Read more...
Your Price
$102.86
In Stock
Maytag Range Sensor
PartSelect Number PS11731446
Manufacturer Part Number W10859573
Experience a seamless cooking process with the Whirlpool Oven Temperature Sensor. An essential part for your range, oven or stove, it accurately measures the temperature inside the oven ensuring your meals are cooked to perfection. This genuine OEM part is compatible with various models of Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef. Disconnecting the power before installing this part is highly recommended for safety reasons. Notably, despite the look-alike nature of many parts, minor size and shape variations could occur, hence, kindly verify the part number with your model before ordering. Finally, do consider wearing work gloves during installation to prevent any possible accidents.
Your Price
$103.32
In Stock
Maytag Range Temperature Sensor
PartSelect Number PS11744537
Manufacturer Part Number WP7430P044-60
Also known as a probe. This temperature sensor detects the temperature within the oven cavity.
Fixes these symptoms
- Little to no heat when baking
- Oven is too hot
- See more...
Your Price
$109.41
In Stock
Maytag Range Temperature Sensor
PartSelect Number PS11757456
Manufacturer Part Number WPY0314907
The temperature sensor is a part for the oven, on your range. This temperature sensor has a body length of just over 3 inches. The purpose of this part is to measure the temperature within the oven and report it back to the control board where it can be displayed. To make this repair you will need a number two Phillips screwdriver or a number two square-head screwdriver. To replace this part, you will need access to the back of the range. This means you will need to pull the range away from the wall, disconnect the power, and remove the back panel.
Fixes these symptoms
- Little to no heat when baking
- Oven is too hot
- Oven not heating evenly
- See more...
Installation Instructions
Suzanne from Acton, MA
Getting F 1 and 2 error codes and the oven turned itself off.
Really easy but in this model there are 2 versions of the sensor, male and female. The website didn't have any place to see that. So the first sensor that came was male but we needed the other. After calling they sent me a return form and sent the new part (which was actually much cheaper) overnight and it went in very quickly. Would check this out again when anything went wrong. they are great folks to work with.
Read more...
Your Price
$79.80
In Stock
Related Maytag Range Parts
- All Maytag Range parts
- Maytag Range Brackets and Flanges
- Maytag Range Caps and Lids
- Maytag Range Circuit Boards and Touch Pads
- Maytag Range Cooktops
- Maytag Range Doors
- Maytag Range Drawers and Glides
- Maytag Range Drip Bowls
- Maytag Range Ducts and Vents
- Maytag Range Elements and Burners
- Maytag Range Fans and Blowers
- Maytag Range Fuses
- Maytag Range Grates
- Maytag Range Handles
- Maytag Range Hardware
- Maytag Range Hinges
- Maytag Range Hoses and Tubes
- Maytag Range Igniters
- Maytag Range Ignitions
- Maytag Range Insulations
- Maytag Range Knobs
- Maytag Range Latches
- Maytag Range Lights and Bulbs
- Maytag Range Manuals and Literatures
- Maytag Range Motors
- Maytag Range Panels
- Maytag Range Power Cords
- Maytag Range Racks
- Maytag Range Seals and Gaskets
- Maytag Range Switches
- Maytag Range Thermostats
- Maytag Range Trims
- Maytag Range Valves
- Maytag Range Wire Plugs and Connectors