Maytag Range Seals and Gaskets

Videos!

Your Price

$9.76

Maytag Range Lint Trap Housing Seal

★★★★★

8 Reviews

PartSelect Number PS11741506

Manufacturer Part Number WP339956

This is foam seal for your dryer. It forms a seal to prevent air from escaping the rear of the dryer drum and the lint duct. This model comes with adhesive backing and is located in between the lint chute and the bulkhead of your appliance. This foam seal is just over 28 inches long and under 1 inch wide. You may need to replace this part if your clothing is taking too long to dry, or if your dryer is not generating enough heat or no heat at all.

Fixes these symptoms

Noisy
Too hot
See more...

Installation Instructions

Eric from Fort Dodge, IA

dryer drum not turning and no air circulating

replaced motor and drum rear seal as well as idler wheels, the old rear drum seal was completly worn out, since I had it all apart, I replaced lint chute and trap seals and belt and tensioner. I spent less money on parts than if I would have bought a new dryer. The motor was the main problem as the bearings were shot. Read more...

Videos!

Your Price

$87.22

Maytag Range Door Gasket

★★★★★

15 Reviews

PartSelect Number PS11749287

Manufacturer Part Number WPW10162384

The oven door gasket on your range functions as a seal between the warm interior of your oven, and the outside. It prevents heat from fleeing your oven when the door is closed. Before making any repairs to your oven you should make sure to wear work gloves to protect your hands, and give your oven time to cool. The only tool you will need to make this repair is a pair of needle nose pliers. This oven door gasket comes with built in retaining clips; if any retaining clips from your old gasket are left in the oven make sure to remove them before installing your new gasket.

Fixes these symptoms

Door won’t close
Little to no heat when baking
Oven is too hot
See more...

Installation Instructions

Lori from Scottsdale, AZ

Needed to replace oven door gasket.

First removed the old gasket using a needle-nose pliers. Then placed new gasket by inserting the little clips on the gasket. Took 5 minutes. Great instructions from Repair Forum. Read more...

Videos!

Your Price

$61.25

Maytag Range Door Seal

★★★★★

5 Reviews

PartSelect Number PS11743947

Manufacturer Part Number WP7212P043-60

This door seal is used for ranges and ovens. The seal prevents hot air escaping from the oven to maintain a certain temperature when baking. The clips sticking out of the seal help secure it to the range doors for the most effective performance. This seal is black in color and is made of rubber. If your oven is not heating evenly, has little to no heat when baking, or is too hot, replacing the seal can solve the problem. The tools needed for this repair are needle nose pliers. Make sure the oven is cool before starting this installation project. Refer to the diagram provided by the manufacturer for further installation instructions.

Fixes these symptoms

Door won’t close
Little to no heat when baking
Oven is too hot
See more...

Installation Instructions

Stella from Charlotte, TN

worn out door seal

removed old clips and remaining parts of old seal...new part already had clips attached, so just snapped them into holes in oven door. Read more...

Your Price

$127.07

Maytag Range Oven Door Seal

★★★★★

5 Reviews

PartSelect Number PS11757564

Manufacturer Part Number WPY702338

This oven door seal prevents heat from escaping the oven cavity when in use.

Fixes these symptoms

Little to no heat when baking
Oven not heating evenly
See more...

Installation Instructions

Paul from Mickleton, NJ

The oven door seal was ripped and was leaking.

The oven seal replacement was very straight forward. Two screws held the door to the arms coming from the oven. I slid the door up off the arm and moved it to a workbench. This whole process should take about 15 minutes, a little longer if your unit is older and you want to clean as you go. Mine was fairly dirty and I gave it a cleaning as I removed parts. Unscrew all screws on the outer frame of the door, including two small ones on the side. Remove the outer frame and then the glass front and set them aside. A few more screws to remove the glass from the inner door, and even more on the remaining part of the door. You should also remove the screws holding the tiny brackets as well to release the portion that holds the oven seal in place. This is very straightforward, just keep pulling screws out until you can remove the old seal.

Once the old seal is out, insert the new one using the wire embedded in the seal as your guide...the gap in the seal goes to the bottom. Put everything back together and re-install the door. My door hinges were spring loaded and took a little effort to move them down so the door can be slipped on. This is a two person job since the hinges do not lock in place, they spring right back up flush with the oven and you cannot install the door. Re-install the two set screws holding the door to the hinges and you are done!

With the new seal in place, it felt a little puffy and the door did not seem to close as flush as it used to. This makes sense since the seal is new. I kept the door locked (like you would to use the oven cleaning cycle). I even kept it partially locked during cooking.

Frankly, the hardest part was the cleanup of nasty grease and dirt that built up over the past decade or so.

Best of luck! Read more...