Maytag Range Hardware

Maytag Appliance Parts

Popular Maytag Range Hardware

Your Price
$6.54
  In Stock
Maytag Range Torx Screw
PartSelect Number PS11741257
Manufacturer Part Number WP3368921
7-18 x 3/4" - sold individually.
Fixes these symptoms
  • Gas igniter glows, but will not light
  • Will Not Start
  • See more...
Installation Instructions
Michael from Dardanelle, AR
Ignitor switches shorted out
The ignitor switches are installed on top of the 4 gas valves for the range top. These switches control the electronic ignition. To replace the switch assembly the top of the range must be removed to gain access.

This was made more difficult by the fact that the screws that hold the burners to the range top were rusted and had to be drilled out so the the burners could be released from the top.

1. Disconnect the power to the range.
2. Open the top oven door.
3. Remove 2 - 1/4" sheet metal screws at the front corners of the range top assy. Remove the Burner knobs and the two Phillps screws that holds the gas valve assembly to the range top.
4. With a drill, remove the tops of the screws to release the burners from the range top. If the screws are in good condition and just unscrew them and the upper burners from the Orifice Holders. (I had to replace the orifice holders because the screws were stuck in them due to rust).
5. When the burners are free, lift the range top at the front and remove it from the range. Disconnect the ignitor wires from the ignitors on each holder.
6. To replace the Orifice Holders, disconnect the gas supply pipes from each holder by loosening the compression nut at the holder using an adjustable wrench. Secure the Orifice Holders when loosening the fittings, BE CAREFUL not to damage the aluminum gas supply pipes.
7. Note that there are 3 different Holders, be sure to use the holder that matches the specific location.
8. For LP gas fueled ranges ONLY, remove the small gas jets from the old holders and install them in place of the parts supplied with the new orifice holders. The new parts contain NATURAL GAS jets which are not compatible with LP gas. Each Different Orifice Holder uses a specific orifice or jet, make certain that the orifice matches the orifice holder. Check for leaks at the gas connections using soapy water.
9. Carefully raise the old ignitor switches (4) off the shafts of the gas valves. Note the top and bottom configuration of the switches
10. Carefully release the wires that come from the rear of the range from the rearmost switch. Press a suitable pin or other suitable tool in a the hole, beside the wire, just enough to release the wire. (Look at the NEW switch assemble to see how this works). Remove the wires from the NEW switch first to see how it is done. Repeat the process on the old switches. (you will re-use the wires that come up from the rear of the range.
11. Install the new switch assembly over the four (4) burner gas valves, take care to align the "D" shaped shafts with the holes in each valve.
12. Insert the wires in the two connections on the rearmost switch. CAUTION!!! Be sure to install the wires so that the color codes agree with the wires on the new switch assembly. Black to black and gray to gray.
13. Install the 4 clear plastic "shields" over the shafts and against the top of each switch.
14. Re-connect the ignitor wires to the burners and Re-Install the range top, in the reverse order of dis-assembly.
Read more...
Your Price
$7.95
  In Stock
Maytag Range Screw - 10-16 x 1
★★★★★
★★★★★
2 Reviews
PartSelect Number PS11741409
Manufacturer Part Number WP3387230
This screw is sold individually.
Installation Instructions
Wendy from BRAINTREE, MA
Freezer handle came loose on one side
Discovered that the seating in the handle was stripped on one side so removed the old handle (toughest part of the repair). Based on a previously asked/answered question, the PartSelect website provided an accurate list of the required parts (and corresponding part numbers) so I had everything I needed. Installing the new handle was very straightforward and quick. Read more...
Your Price
$7.95
  In Stock
Maytag Range Screw
★★★★★
★★★★★
1 Review
PartSelect Number PS11750186
Manufacturer Part Number WPW10200660
Installation Instructions
Judith from SALEM, OR
Replaced screw
By hand screwdriver Read more...
Your Price
$8.04
  In Stock
Maytag Range Installation Screw
★★★★★
★★★★★
2 Reviews
PartSelect Number PS11741612
Manufacturer Part Number WP3400882
This screw is sold individually.
Your Price
$5.42
  In Stock
Maytag Range Screw, 8/18 x 3/8
★★★★★
★★★★★
2 Reviews
PartSelect Number PS11746840
Manufacturer Part Number WP90767
This screw is sold individually.
Installation Instructions
Alexander from Lakeland, FL
Broken Dryer Knob
First let me just say that Partselect.com is now one my stored favorites in my web browser. I came home from a business trip and saw a pair of pliers on the dryer. I thought that was odd until my wife informed me that the knob on the dryer had broken. So she was using the pliers to select the cycle. Somehow she knew where the missing pointer was actually pointing. Since the dryer was over 5 years old I saw this as an opportunity to upgrade both appliances. Not with my frugal wife. A search of the Internet popped up partselect. I ordered Wednesday morning and the parts where on my doorstep late Thursday. Trust me I was very surprised. Everything worked perfectly. Two thumbs up!!! Read more...
Your Price
$7.95
  In Stock
Maytag Range Screw with Washer
★★★★★
★★★★★
1 Review
PartSelect Number PS11744138
Manufacturer Part Number WP74006515
This is a replacement screw and washer for your oven/range. It is a Phillips-head screw approximately half an inch long, and the washer is approximately 1 inch in diameter. The screw attaches the oven door handle to the door. This part is sold individually and is an authentic OEM part sourced directly from the manufacturer.
Installation Instructions
Tom from Huntingtown, MD
The handle on the upper oven broke off at both attachment points.
The repair process is not logical. It appears as if it were engineered for the average person to not be able to fix it. The advice from previous posters was invaluable.
Remove the door from the hinges. Then remove all the screws from the four outer panels. The glass window will fall out, be careful. It's OK, though, it probably needs cleaned like ours did. The new handle is now easily replaced. However, the replacement handle has cheap, plastic attachment points, vice the original's metal ones (which broke after a couple years.) As I was screwing in one of the new screws, I felt it already stripping...at least I now know how to replace the handle when it breaks again.

Partselect.com beat Maytag on the overall price. Maytag sold the handle cheaper but the screws were three time the cost and shipping was twice the cost. I bought the standard shipping (2-3 days) , but the part came the next day! Yea Partselect!!

This is what I learned: Partselect is great...Maytag makes junk.
Read more...
Your Price
$8.04
  In Stock
Maytag Range Screw
★★★★★
★★★★★
4 Reviews
PartSelect Number PS3651485
Manufacturer Part Number W10491985
Sold individually.
Installation Instructions
Quail Valley from Clive, IA
Glass broken on outside oven door
Checked to see that I had all the parts I needed.
Installed bottom door trim then side trim pieces.
Do not tighten screws. Install door handle with top
trim attached over glass. Tighten screws just snug
all around.
Read more...
Your Price
$7.84
  In Stock
Maytag Range Screw, Igniter
★★★★★
★★★★★
3 Reviews
PartSelect Number PS11745563
Manufacturer Part Number WP8273062
This screw is sold individually.
Installation Instructions
Didier from LONE TREE, CO
Ignitor did not work
- Removed the cover.
- Removed te two Torx screws.
- Pulled the burner a couple of inches to be able to disconnect the wire.
- Spent a lot of time removing the small Philips screw holding the ignitor. Ended up breaking the ignitor with pliers to be able to put WD40 under the screw's head.
- Treated all screws with a high temperature copper paste to prevent oxidation.
Installed the new ignitor with the new screw.
- Reconnected the wire.
- Installed the two Torx screws.
- Voila, it works.
Read more...
Your Price
$8.61
  In Stock
Maytag Range Screw
PartSelect Number PS11755179
Manufacturer Part Number WPW10465148
This part is the replacement screw for your range. The head is approximately 1/2 an inch in diameter and the screw is approximately 1 inch in length. It is made of metal and is sold individually. This screw is used in fastening together the individual parts of the range door. It is an authentic OEM part sourced directly from the manufacturer.
Your Price
$7.91
  In Stock
Maytag Range Screw
★★★★★
★★★★★
1 Review
PartSelect Number PS11742721
Manufacturer Part Number WP488729
Metallic screw that is less than an inch long. Does not include the plastic washer.
Installation Instructions
Kyle from Wimauma, FL
Black Cam was bren on lower door hinge
This was a very simple job. Remove the top Hinge bracket, a total of 4 screws, lifted the door off the bottom hinge, removed the bottom hinge set up, 2 screws, replaced it, and attached the new bottom black door cam, lifted the door back onto the bottom hinge and aligned the top hinge, and reinserted the screws, and Ta Da, The door works like a new refrigerator door. 15 to 30 min tops. I did not even have to take the refrigerator items out of there door holder. Read more...

Related Maytag Range Parts