Whirlpool Cooktop Elements and Burners

Whirlpool Appliance Parts
Shop By Part Type

Popular Whirlpool Cooktop Elements and Burners

Your Price
$14.64
  In Stock
Surface Burner Receptacle Kit
★★★★★
★★★★★
(18)
PartSelect Number PS1570190
Manufacturer Part Number 12001676
The tools you will need to replace the surface burner receptacle kit on your range include a Phillips screw driver, and a pair of wire strippers. Before doing this repair, make sure to disconnect your appliance from the power supply and wear work gloves to protect your hands. The surface burner receptacle kit comes with a plastic block, high temperature wire nuts, a metal bracket, and wires. This part functions as the connection between the wire harness and the surface element in your range.
Fixes these symptoms
Installation Instructions
Richard from Carthage, NC
Stove top element not working due to bad receptacle.
Turned off the power at the breaker box, cut the wires approximately 5 inches from the bad receptacle and removed it after removing one screw. Stripped back the wires about 1/2 inch and attached the new wires with the ceramic wire nuts provided and secured the receptacle back in place with the new screw provided in the kit.
My sister's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts.
The element is working great now.
Whenever I need appliance parts again I'll use partselect.com.
Read more...
Your Price
$9.33
  In Stock
Burner Grate Pads - Kit of 5
★★★★★
★★★★★
(6)
PartSelect Number PS389174
Manufacturer Part Number 814323
These pads go on the bottom of your gas cooktop grates to prevent them from moving and scratching the top of your appliance.
Installation Instructions
Sabrina from Mooresville, NC
several grate pads fell out/lost /broke during cleaning
The only real issue was locating the proper adhesive to ensure that the new pads would not fall out. The small insert paper slip in the package noted that a RTV adhesive should be used. After much searching at the home improvement super store, I learned it would be found at an auto supply store. It is black, and is for high temp use. It is available in a small tube for around $2.00. The RTV is usually used to make gaskets for heat/oil exposure in auto repair. I did have trouble removing a broken stub from a pad that had broken off in the hole. I used an awl to get what I could and push the rest into the hole deeper, then insert a new pad with along with the adhesive. Read more...
Your Price
$37.52
  In Stock
Standard Y-Frame Range Surface Burner
★★★★★
★★★★★
(10)
PartSelect Number PS11743366
Manufacturer Part Number WP660532
The standard y-frame surface burner provides heat to your range. If you notice that your element will not heat, you may need to replace your surface burner. This product is 6 inches in diameter, and 1500W. The manufacturer suggests replacing the receptacle at the same time that you replace the surface burner. Many of our customers have rated this repair as very easy, and you will not need any tools. To complete the repair, simply lift out the old burner and replace it with the new one. Check that the burners are turned off before you begin this repair.
Fixes these symptoms
Installation Instructions
Laurie from Tequesta, FL
Burner element broke and drip bowls needed to be replaced.
I went to the local discount mart and bought drip bowls. The ones available at that store did not fit, so I decided to buy directly from the stove's manufacturer distributor.

The drip pans were simple to replace, as was the new burner element. My old one had broke and was still working, but I decided to replace it when I ordered the drip pans.

Everything was easy to install and it looks like a brand new new stove top! I saved a lot of money doing it myself.
Read more...
Your Price
$49.09
  In Stock
Surface Burner - 8 Inch - 2600W
★★★★★
★★★★★
(15)
PartSelect Number PS11743367
Manufacturer Part Number WP660533
The surface burner or element on your range provides the heat that you cook with. If your element will not heat, you may need to replace the surface burner. This surface burner is 8 inches in diameter and 2600 watts. The burner element is made of metal and has two prongs that connect it to the range. The manufacturer recommends you replace the burner receptacle at the same time that you replace the surface burner. Many of our customers have rated this repair as very easy. To complete the repair simply lift the old burner up and out, and replace it with the new one. Be sure to disconnect power to the range before beginning this repair.
Fixes these symptoms
Installation Instructions
Jonathan from Lilburn, GA
8 inch burner wouldn't come on. Wires shorted out
One screw holds the block onto the stove top. Had to clean out fitting for phillips screwdriver or screw would have stripped because it was old with lots of buildup. Even cleaned out, this screw required great force with phillips screwdriver to keep from stripping. Caution! If you strip it, you'll have to drill it out! The rest was a snap. Cut the old wires leading to the old block (not too close to where wires disappear into back of stove, though!). Strip insulation off both wires and attach with the connectors that came in the kit. Then push the wires into the block, and finally, attach the block back to the stove top (new screw is supplied). Restore power and everything should be fine. One problem: Roper/Whirlpool built their appliance in such a way that when the connector block shorts out, it usually takes the infinite switch with it. So I ended up having to go back and purchase that switch as well (which just so happens to cost twice to three times as much!). If you put it all back together and it still doesn't work, that's probably what happened, so go ahead and remove the knob panel and check that switch (it's right behind the control knobs on the front). You will probably find a burned connector at the back top left or the switch. Don't forget to write down which wire goes where (or just take a picture of it). Read more...
Your Price
$143.31
  On Order
Dual Surface Element - 2500w/1200w
★★★★★
★★★★★
(9)
PartSelect Number PS11764902
Manufacturer Part Number W10823692
This is the replacement large surface element for your cooktop or range. It is approximately 10-inches in diameter and is 1200/2500 watts. The large surface element is installed under the cooktop and heats up the area directly above it. You will need to replace the element if it does not heat up properly. As you will be working around electricity, be sure that your range is disconnected from power before you begin this repair. This is an OEM part sourced directly from the manufacturer.
Fixes these symptoms
Installation Instructions
GEORGE from NEWNAN, GA
Radiant element, 2400 watt, under Ceran glass cok top needed replacement.
turned off power
removed ceran top from cabinet
removed element
installed new element
replaced top
powered up and was done
Read more...
Your Price
$31.61
  In Stock
Receptacle Kit
★★★★★
★★★★★
(9)
PartSelect Number PS389217
Manufacturer Part Number 814399
This assembly of parts is a surface burner receptacle kit, and is used in conjunction with your range. The assembly comes with two wires, two wire nuts, two pieces of heat-shrink tubing, and the receptacle. If your element is not heating, you may need to replace your surface burner receptacle. The function of this part is to connect the surface element to the wire harness. The tools you will need for this installment include a number two square-head screwdriver or a number two Phillips screwdriver, a pair of wire strippers and crimpers, and a heat gun.
Fixes these symptoms
Installation Instructions
Tim from Pittsford, NY
Stove would not heat up
Cut old wires to receptacle, striped the wires, wire nutted to new receptacle, screwed new receptacle into stove and installed heating element.

Piece of cake, but then again my degree is in electrical engineering so I should be able to handle a couple of wire nuts.
Read more...
Your Price
$143.31
  In Stock
Element with Limiter 6 Inch - 1200W
★★★★★
★★★★★
(11)
PartSelect Number PS11764915
Manufacturer Part Number W10823711
This is a radiant surface element with limiter, and it works in conjunction with your range. The function of this part is to give heat to the surface directly above it, on cooking area stove top.This model is sold individually and is 1200 watts. The main reason for needing to replace this part is if your element will not heat. Before ordering, make sure to test your stove top radiant element for continuity to make sure it is the problem. To make this installation you will need a Phillips screwdriver, and a 14-inch nut driver.
Fixes these symptoms
Installation Instructions
Mark from Loxahatchee, FL
Right rear burner went bad
Turned the breaker off, I removed 2 screws securing the range top to the range, opened the top and secured it in the up position, Removed the 2 screws securing the element ,one at a time I swapped the quick connectors from the old element to the new and repeated the process in reverse. I save over $100.00 in labor, plus most companies get you for a trip charge. It was easy!! Read more...
Your Price
$80.75
  On Order
Surface Burner Element - 8 Inch
★★★★★
★★★★★
(2)
PartSelect Number PS11740903
Manufacturer Part Number WP3191454
This large surface burner is 2100W.
Fixes these symptoms
Installation Instructions
Gary from Shirley, IN
broken terminal
Simply removed the old heating element and plug the new element terminals into socket. Read more...
Your Price
$128.82
  In Stock
Surface Element - 3000/1400W
PartSelect Number PS11764929
Manufacturer Part Number W10823729
Fixes these symptoms
Installation Instructions
MELISSA from CHAPLIN, CT
lost two burners
repair was very easy 20 mins and it was done Read more...
Your Price
$143.31
  In Stock
Surface Radiant Element with Limiter
★★★★★
★★★★★
(2)
PartSelect Number PS11764906
Manufacturer Part Number W10823696
Sold individually.
Fixes these symptoms
Installation Instructions
Robert from Blackwood, NJ
Right Front Surface Element would not heat
Turn off the power to the Electric Oven.
Remove the 2 screws to the oven top at the front of the stove. Lift the oven top up. Have someone hold it for you. Label the wires that go to the element you are going to replace. Disconnect the wires from the Element. Remove the screw from the bracket that holds the front and rear element in place. It is located at the back of the bracket behind the rear element and you will need small phillips head screw driver. Remove the bad element.. Unscrew the two pointed bracket holder pieces from the old element and screw them into the new element in the same location as the old. Put the new element back into the bracket and put the bracket mount screw back in. Attach the wires back to the new element. Close the oven top. Install the oven top screws at the front of the stove. Turn the power back on and test the element.
Read more...

Related Parts