Whirlpool Cooktop Hardware
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Whirlpool Cooktop Hardware
Your Price
$6.25
In Stock
Whirlpool Cooktop Range Torx Screw
This was made more difficult by the fact that the screws that hold the burners to the range top were rusted and had to be drilled out so the the burners could be released from the top.
1. Disconnect the power to the range.
2. Open the top oven door.
3. Remove 2 - 1/4" sheet metal screws at the front corners of the range top assy. Remove the Burner knobs and the two Phillps screws that holds the gas valve assembly to the range top.
4. With a drill, remove the tops of the screws to release the burners from the range top. If the screws are in good condition and just unscrew them and the upper burners from the Orifice Holders. (I had to replace the orifice holders because the screws were stuck in them due to rust).
5. When the burners are free, lift the range top at the front and remove it from the range. Disconnect the ignitor wires from the ignitors on each holder.
6. To replace the Orifice Holders, disconnect the gas supply pipes from each holder by loosening the compression nut at the holder using an adjustable wrench. Secure the Orifice Holders when loosening the fittings, BE CAREFUL not to damage the aluminum gas supply pipes.
7. Note that there are 3 different Holders, be sure to use the holder that matches the specific location.
8. For LP gas fueled ranges ONLY, remove the small gas jets from the old holders and install them in place of the parts supplied with the new orifice holders. The new parts contain NATURAL GAS jets which are not compatible with LP gas. Each Different Orifice Holder uses a specific orifice or jet, make certain that the orifice matches the orifice holder. Check for leaks at the gas connections using soapy water.
9. Carefully raise the old ignitor switches (4) off the shafts of the gas valves. Note the top and bottom configuration of the switches
10. Carefully release the wires that come from the rear of the range from the rearmost switch. Press a suitable pin or other suitable tool in a the hole, beside the wire, just enough to release the wire. (Look at the NEW switch assemble to see how this works). Remove the wires from the NEW switch first to see how it is done. Repeat the process on the old switches. (you will re-use the wires that come up from the rear of the range.
11. Install the new switch assembly over the four (4) burner gas valves, take care to align the "D" shaped shafts with the holes in each valve.
12. Insert the wires in the two connections on the rearmost switch. CAUTION!!! Be sure to install the wires so that the color codes agree with the wires on the new switch assembly. Black to black and gray to gray.
13. Install the 4 clear plastic "shields" over the shafts and against the top of each switch.
14. Re-connect the ignitor wires to the burners and Re-Install the range top, in the reverse order of dis-assembly. Read more...
PartSelect Number PS11741257
Manufacturer Part Number WP3368921
7-18 x 3/4-Inch - sold individually.
Fixes these symptoms
- Gas igniter glows, but will not light
- Will Not Start
- See more...
Installation Instructions
Michael from Dardanelle, AR
Ignitor switches shorted out
The ignitor switches are installed on top of the 4 gas valves for the range top. These switches control the electronic ignition. To replace the switch assembly the top of the range must be removed to gain access. This was made more difficult by the fact that the screws that hold the burners to the range top were rusted and had to be drilled out so the the burners could be released from the top.
1. Disconnect the power to the range.
2. Open the top oven door.
3. Remove 2 - 1/4" sheet metal screws at the front corners of the range top assy. Remove the Burner knobs and the two Phillps screws that holds the gas valve assembly to the range top.
4. With a drill, remove the tops of the screws to release the burners from the range top. If the screws are in good condition and just unscrew them and the upper burners from the Orifice Holders. (I had to replace the orifice holders because the screws were stuck in them due to rust).
5. When the burners are free, lift the range top at the front and remove it from the range. Disconnect the ignitor wires from the ignitors on each holder.
6. To replace the Orifice Holders, disconnect the gas supply pipes from each holder by loosening the compression nut at the holder using an adjustable wrench. Secure the Orifice Holders when loosening the fittings, BE CAREFUL not to damage the aluminum gas supply pipes.
7. Note that there are 3 different Holders, be sure to use the holder that matches the specific location.
8. For LP gas fueled ranges ONLY, remove the small gas jets from the old holders and install them in place of the parts supplied with the new orifice holders. The new parts contain NATURAL GAS jets which are not compatible with LP gas. Each Different Orifice Holder uses a specific orifice or jet, make certain that the orifice matches the orifice holder. Check for leaks at the gas connections using soapy water.
9. Carefully raise the old ignitor switches (4) off the shafts of the gas valves. Note the top and bottom configuration of the switches
10. Carefully release the wires that come from the rear of the range from the rearmost switch. Press a suitable pin or other suitable tool in a the hole, beside the wire, just enough to release the wire. (Look at the NEW switch assemble to see how this works). Remove the wires from the NEW switch first to see how it is done. Repeat the process on the old switches. (you will re-use the wires that come up from the rear of the range.
11. Install the new switch assembly over the four (4) burner gas valves, take care to align the "D" shaped shafts with the holes in each valve.
12. Insert the wires in the two connections on the rearmost switch. CAUTION!!! Be sure to install the wires so that the color codes agree with the wires on the new switch assembly. Black to black and gray to gray.
13. Install the 4 clear plastic "shields" over the shafts and against the top of each switch.
14. Re-connect the ignitor wires to the burners and Re-Install the range top, in the reverse order of dis-assembly. Read more...
Your Price
$7.30
In Stock
Whirlpool Cooktop Range Igniter Screw
- Removed te two Torx screws.
- Pulled the burner a couple of inches to be able to disconnect the wire.
- Spent a lot of time removing the small Philips screw holding the ignitor. Ended up breaking the ignitor with pliers to be able to put WD40 under the screw's head.
- Treated all screws with a high temperature copper paste to prevent oxidation.
Installed the new ignitor with the new screw.
- Reconnected the wire.
- Installed the two Torx screws.
- Voila, it works. Read more...
PartSelect Number PS11745563
Manufacturer Part Number WP8273062
This screw is sold individually.
Fixes these symptoms
- Gas igniter glows, but will not light
- Will Not Start
- See more...
Installation Instructions
Didier from LONE TREE, CO
Ignitor did not work
- Removed the cover.- Removed te two Torx screws.
- Pulled the burner a couple of inches to be able to disconnect the wire.
- Spent a lot of time removing the small Philips screw holding the ignitor. Ended up breaking the ignitor with pliers to be able to put WD40 under the screw's head.
- Treated all screws with a high temperature copper paste to prevent oxidation.
Installed the new ignitor with the new screw.
- Reconnected the wire.
- Installed the two Torx screws.
- Voila, it works. Read more...
Your Price
$20.95
In Stock
Whirlpool Cooktop Washer Screw
PartSelect Number PS12741703
Manufacturer Part Number W11404293
Sold individually.
Fixes these symptoms
- Lid or door won’t close
- See more...
Installation Instructions
Ed from NEW BERN, NC
Replace hinge and hinge spring assembly.
I mounted the left and right hinge assemblys into the washer (spring assembly) and then mounted the glass top on to the hinge assemblies. Inserted the screws and tightened as required.
Read more...
Your Price
$7.30
In Stock
Whirlpool Cooktop Dryer Screw
PartSelect Number PS11746840
Manufacturer Part Number WP90767
This screw is sold individually.
Installation Instructions
Alexander from Lakeland, FL
Broken Dryer Knob
First let me just say that Partselect.com is now one my stored favorites in my web browser. I came home from a business trip and saw a pair of pliers on the dryer. I thought that was odd until my wife informed me that the knob on the dryer had broken. So she was using the pliers to select the cycle. Somehow she knew where the missing pointer was actually pointing. Since the dryer was over 5 years old I saw this as an opportunity to upgrade both appliances. Not with my frugal wife. A search of the Internet popped up partselect. I ordered Wednesday morning and the parts where on my doorstep late Thursday. Trust me I was very surprised. Everything worked perfectly. Two thumbs up!!!
Read more...
Your Price
$9.40
In Stock
Whirlpool Cooktop Range Rubber Grommet
PartSelect Number PS11752223
Manufacturer Part Number WPW10293874
Sold individually.
Installation Instructions
CHARLES from SPRING HILL, FL
Knobs slipping
Remove old knobs and remove old grommets. Insert new grommets, install new knobs.
Read more...
Your Price
$7.30
In Stock
Whirlpool Cooktop Air Conditioner Cover Screw
In this spirit of any repair, I replaced them, and it was not the issue. I don't know what I expected.
Ceiling. YouTube. Pacing.
Then I figured it was this part - the motor coupling. I unplugged the machine and took out the drain tube. I leaned the machine back and propped it up with an empty detergent bottle, because those were abundant. Ratchet off a few bolts and the motor comes out. The coupling was indeed broken. The new one slips right in - I tapped it a few times with a mallet for good measure / vengeance. Ratcheted the bolts back on and tipped it back up.
Pros: Washer works now.
Cons: Everest-esque laundry pile to address.
But hey, it worked! I am no handyman and it wasn't too bad at all. Half hour tops. Read more...
PartSelect Number PS11740701
Manufacturer Part Number WP308685
Sold individually.
Installation Instructions
Peter from WRENTHAM, MA
Kenmore 80 Series Washer - Agitator Stopped Working
First I screamed at the ceiling, because I have a three year old and an infant, and the washing machine was dead. Then I went to youtube. It seemed like the "agitator dogs" were the issue. In this spirit of any repair, I replaced them, and it was not the issue. I don't know what I expected.
Ceiling. YouTube. Pacing.
Then I figured it was this part - the motor coupling. I unplugged the machine and took out the drain tube. I leaned the machine back and propped it up with an empty detergent bottle, because those were abundant. Ratchet off a few bolts and the motor comes out. The coupling was indeed broken. The new one slips right in - I tapped it a few times with a mallet for good measure / vengeance. Ratcheted the bolts back on and tipped it back up.
Pros: Washer works now.
Cons: Everest-esque laundry pile to address.
But hey, it worked! I am no handyman and it wasn't too bad at all. Half hour tops. Read more...
Your Price
$7.30
In Stock
Whirlpool Cooktop Screw
PartSelect Number PS11742721
Manufacturer Part Number WP488729
Metallic screw that is less than an inch long. Does not include the plastic washer.
Installation Instructions
Kyle from Wimauma, FL
Black Cam was bren on lower door hinge
This was a very simple job. Remove the top Hinge bracket, a total of 4 screws, lifted the door off the bottom hinge, removed the bottom hinge set up, 2 screws, replaced it, and attached the new bottom black door cam, lifted the door back onto the bottom hinge and aligned the top hinge, and reinserted the screws, and Ta Da, The door works like a new refrigerator door. 15 to 30 min tops. I did not even have to take the refrigerator items out of there door holder.
Read more...
Your Price
$7.30
In Stock
Whirlpool Cooktop Screw
Installed bottom door trim then side trim pieces.
Do not tighten screws. Install door handle with top
trim attached over glass. Tighten screws just snug
all around. Read more...
PartSelect Number PS3651485
Manufacturer Part Number W10491985
Sold individually.
Installation Instructions
Quail Valley from Clive, IA
Glass broken on outside oven door
Checked to see that I had all the parts I needed.Installed bottom door trim then side trim pieces.
Do not tighten screws. Install door handle with top
trim attached over glass. Tighten screws just snug
all around. Read more...
Your Price
$7.30
In Stock
Whirlpool Cooktop Range Screw
PartSelect Number PS11740977
Manufacturer Part Number WP3196163
This screw is sold individually.
Your Price
$7.30
In Stock
Whirlpool Cooktop Appliance Screw
The burner unit slides out easily and after unscrewing the sides, you have to disconnect the wires from the underside of the igniters. The venturi tubes and igniters then unscrew from the underside of the burners which twist right out of the assembly. Re-Assembly is very intuitive looking at it and it all goes right back together as it came out. Took 45 minutes total and that includes fighting with some screws that had rusted onto the burner.
Reading some of the previous reviews, current prices are double to triple what other people did the repair for leading me to believe parts won't be available for much longer. Make the repair while you still can! Read more...
PartSelect Number PS11743002
Manufacturer Part Number WP59002061
Sold individually.
Installation Instructions
John from WAKEFIELD, MA
Flames appeared outside of burners
The front burner had a noticible flame coming from the base, so I originally purchased a single burner to replace it (you could see a corroded hole at the bottom). Upon taking the unit apart, I noticed the corrosion was much worse than met the eye. Given the age of the unit and that some parts were already becoming discontinued I decided to gut the whole thing and replace it all.The burner unit slides out easily and after unscrewing the sides, you have to disconnect the wires from the underside of the igniters. The venturi tubes and igniters then unscrew from the underside of the burners which twist right out of the assembly. Re-Assembly is very intuitive looking at it and it all goes right back together as it came out. Took 45 minutes total and that includes fighting with some screws that had rusted onto the burner.
Reading some of the previous reviews, current prices are double to triple what other people did the repair for leading me to believe parts won't be available for much longer. Make the repair while you still can! Read more...
Related Whirlpool Cooktop Parts
- All Whirlpool Cooktop parts
- Whirlpool Cooktop Brackets and Flanges
- Whirlpool Cooktop Caps and Lids
- Whirlpool Cooktop Cooktops
- Whirlpool Cooktop Drip Bowls
- Whirlpool Cooktop Elements and Burners
- Whirlpool Cooktop Fuses
- Whirlpool Cooktop Grates
- Whirlpool Cooktop Igniters
- Whirlpool Cooktop Ignitions
- Whirlpool Cooktop Insulations
- Whirlpool Cooktop Knobs
- Whirlpool Cooktop Lights and Bulbs
- Whirlpool Cooktop Seals and Gaskets
- Whirlpool Cooktop Switches
- Whirlpool Cooktop Trims
- Whirlpool Cooktop Valves
- Whirlpool Cooktop Wire Plugs and Connectors