This is a hinge with roller for the oven door on your range. The roller allows you to open and close the door with ease and control. If your door is not opening easily, you may need to replace this part. To make this repair you will need a Phillips screwdriver and a pair of pliers. Take note that this model is only for the right-hand side of your unit, to replace the left-hand side, see the related parts section. We recommend replacing both hinges at the same time.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Door won’t close | Door won’t open after self cleaning cycle
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Frank
December 7, 2019
I need to replace a door hinge on our range. The parts listed are identified as "right" or "left". Is this determined by standing in front of the range, looking into the oven, then matching with my corresponding left and right sides ?
For model number jsp38gov1bb
Hi Frank, when parts are labelled as right or left side on a model this is usually based on your perspective when standing in front of the model. So standing in front of the range and looking directly at it, your left side is what they would call a left side part and your right side is a right side part. Thank you for your question and good luck with your repair!
Before removing screws, I reached in and felt for where the upper end of the spring attached to the hinge. There are three holes in the end of the hinge arm, so I wanted to be sure of which hole to use. (The holes are very close together, so if the spring falls out before you determine which hole it was in, it probably won't matter so long as you are sure to use the same hole on both new hinges.) I then removed three Phillips screws per hinge. Once the hinge was loose, I could wiggle it around and release enough of the spring tension to slip the top end of the spring out of the hole on the hinge arm. Then I pulled out the old hinge and inserted the new one and replaced the three screws. Without the tension, the lower end of the spring fell out of the little hole in the oven bottom where it normally attaches. Our gas oven has a broiler rather than a storage drawer, so it was a little difficult to get the lower tip of the spring back into that hole. It actually ended up being easier to get the lower tip of the spring back into that hole first, before trying to reattach it to the hinge arm. Once I got the lower end into that hole, I pulled up on the spring and maintained upward pressure on the spring while I fiddled around to get the upper end into the hinge arm hole. Took about 20 minutes, door works perfectly now. Lots of sharp edges inside the oven, so had to be careful.
Removed old hinges and installed new hinges. Hardest part was determining that worn hinges were the cause of problem, then ordering replacements. GE website hinge on exploded view did not look like hinges I removed.Thanks to Google I got on to PartSelect.com website where excellent pictures of hinges and one-inch grid confirmed they sold exactly what I wanted for my 13-year old range, the model number of which was not even on the GE website.
Oven door hinge roller deteriorated, oven door hard to open.
Open and slide door upward off of hinges. Removed bottom drawer to access hinge spring. Detached spring, noting proper hole in hinge for reinstallation. Removed three screws holding hinge and removed hinge. Compared new part to old...exact match. Inserted hinge, and reinstalled the three screws. Reattached spring in hinge hole. Slid door back down onto hinges. Done in four minutes flat!
Craig from Kernersville, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
3 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The oven door would not open or close all the way. The plastic hinge roller guides broke on both sides.
Remove oven door from hinges, by pulling it straight up and off, (like you would do for closer access to clean inside). Remove the storage drawer. Lift up and away off the track, (like a file cabinet drawer). With the drawer out and away, you can see how the springs are easily detached from each hinge. Note the location of where the springs attach to the hinges, and bottom of stove. Remove each spring. Three screws on each side hold the hinges on. Unscrew, and set them aside. (The new hinges did not have new screws in package.) Place new hinge in place. Reinstall in reverse of disassembly. If any part of the door or face of the stove (where hinges mount) was bent slightly due to forcing door open, reform with light hammer taps and C-clamps. Enjoy for ANOTHER 10+ years, because it's a GE Profile Stove : )
After tilting the oven door out and sliding it up to remove it, I slid the storage drawer our completely from the range. After removing the spring that held the hinge assembly under tension, I removed 3 phillips head screws that held the existing assembly in place and removed it. After verifying the part you sent was an exact match, I reinstalled the new part, fastened the screws, attached the tension spring, installed the storage drawer, and then slid the oven door back in place on the brackets, completing the repair.
Gary from St. Augustine, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
2 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven door would not stay open.
Called in and talked to someone and he look yup what he thought was correct but after i got them theywere wrong so i sent them back for a full refund minus 9.90 freight. I still need to figure out what i need for my 27 inch wall oven. Please help. Thanks
Hinge design is weak: Hinge roller wheel splits; it's been replaced twice in last two years
1. Slide oven door off hinge arms and set aside 2. Slide out oven bottom drawer and set aside 3. Detach springs from perforations in stove rails then hinges and set aside 4. Loosen three screws in each hinge, remove and set aside. 5. Remove hinges, threading them out through openings 6. Thread new hinges into stove openings. Align hinge arms with hinge wheels. 7. Align and tighten three hinge screws in each hinge. 8. Re-attach springs to perforations in hinge, then stove rails 9. Slide oven drawer into stove and door into hinge arms
The right side hinge roller broke making the door balky
Lifted the door off the hinges, unhooked the spring from each hinge, unscrewed 3 Phillips head screws from the face plate of each hinge and removed the hinge assemblies . Hinges went in the way they came out; easy shmeasy. Took less than 15 minutes and the door is like new.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Carol S - July 17, 2022
Verified Purchase
perfect fit, but...
wish the description mentioned we should have bought the screws as well...
★★★★★
★★★★★
Kyle A - May 11, 2022
Verified Purchase
Works exactly as expected.
Arrived quickly and fit perfectly.
★★★★★
★★★★★
Stephen H - March 16, 2019
Verified Purchase
bad
we had ordered the parts and it was shipped by fed ex smartpost which then tranfered the package to the post office using thier systm, at which point could not be found since there is no tracking # after it arrived from fed ex, the reason why it disappeared i found out after spending much more of my time than was done to deliver it was , when i ordered it the box# was removed because your system said it wasnot a real address so it removed the postal info required for smartpost to work. what a cost killing, customer killing event. either you do not know how your own shipping works or ou should ship u.s.p.s. and avoid all of the returns and mad customers. the package is on its way back lets hope you donot use same method on returns, smartpost, we are waiting for our refund
★★★★★
★★★★★
Wayne T - January 21, 2019
Verified Purchase
The install was easy but the bagged parts were wrongly packaged.
I ordered the one for the right and then the part for the left. Both parts came with separate bags labeled appropriately but the parts in each bag were identically the same.
January 22, 2019
Hello,
Thank you for leaving a review on the part ordered. I have sent you an email in regards to the order. Hope to hear from you!
★★★★★
★★★★★
William M - August 21, 2018
Verified Purchase
It was easy to repair. No problems
It was the right part and not difficult to install. Removed the drawer and located the spring. The only slightly difficult part was unhooking the spring. The job took about 15 minutes and all is working well.
★★★★★
★★★★★
Joe E G - August 10, 2018
Verified Purchase
Oven Hinges
I thought the items were rather pricey for such simple parts. Otherwise they were simple to install thanks to the reviewers who explained how on your web page. Perhaps you ould add a one page instruction sheet for other users.
★★★★★
★★★★★
Robert P - June 23, 2018
Verified Purchase
Easy
No problem installing.
★★★★★
★★★★★
Roger B - June 3, 2018
Verified Purchase
Repair Complete
I received the part that I needed very quickly. I used all of it except the part that has the three holes in it. I had to drill a rivet to remove the unneeded part. I then was able to rivet the replacement part, and everything worked perfectly. Thank you for helping me to fix my oven easily and quickly. Roger
★★★★★
★★★★★
Lawrence J - May 16, 2018
Verified Purchase
All fixed: easily, conveniently
Our oven had a broken hinge for longer than I care to admit. Once I realized that I could replace the hinge by ordering the part, everything went smoothly, quickly, and easily.
★★★★★
★★★★★
R.E. C - February 14, 2018
Verified Purchase
I'm my wife's hero!
I replaced the bad hinge before she got home. Laid out more tools around the kitchen then it actually took to do the job. So, after explaining how "difficult it was" (which it wasn't difficult at all!) she rewarded me with chocolate chip cookies fresh from her now "LIKE NEW" oven! Thank you Part Select!
This is known as a hinge with roller and it is for the oven door of your range. The hinge with roller allows you to easily open and close your oven door without much effort. Take note that your appliance requires two hin...
Model Cross Reference
This part works with the following models:
PartSelect Number: PS231612
Manufacturer Part Number: WB14X104
With our Fix app model plate image recognition technology, we'll recommend the parts guaranteed to fit your appliance. Simply snap a photo, and we'll take care of the rest.
"I love love love this app. It's so nice to have useful information (receipts, manuals, parts lists, warranty info, pictures, etc.) on all of my household appliances and devices in one place."
You added to your cart
✖
$
Qty:
Total item(s) in cart:
Order Subtotal
$
*Taxes and shipping will be applied during checkout