Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
This 6-pin shift actuator is an authentic OEM part supplied directly by the manufacturer for use in washing machines. The shift actuator is responsible for controlling the movement of the washer transmission during the different phases of the wash cycle. This allows the washer to switch between agitating and spinning modes. Signs of a faulty shift actuator include the washer failing to agitate or spin, incomplete cycles where the washer gets stuck in one phase, or unusual noises during operation
How Buying OEM Parts Can Save You Time and Money
Why buy the real thing?
OEM stands for Original Equipment Manufacturer. Simply put, this means that the company who made your appliance is also supplying the replacement part for it.
Replacing your Whirlpool Washer Shift Actuator - 6 Pin
Troubleshooting
This part fixes the following symptoms:
Will not agitate
Spinning Issues
Cycle Not Advancing
Spins slowly
Will Not Start
Will not drain
This part works with the following products:
Washer
Washer Dryer Combo
Part# W10913953 replaces these:
AP6037270, W10815026, W10913953VP
Customer Reviews
Average Rating:
★★★★★
★★★★★
17 Reviews
5.0
Filter By Rating:
5 Stars
17
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
0
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Richard B - August 20, 2019
Verified Purchase
Easy repair
Replacement part took care of issue
★★★★★
★★★★★
John K - October 16, 2020
Verified Purchase
Worked as it should
Part came in on-time,repair went smoothly, up an running again
★★★★★
★★★★★
Richard T - August 14, 2023
Verified Purchase
Perfect
Works , 10 minute install what more can I say ? Oh , delivered in 2 days , so absolutely no complaints.
★★★★★
★★★★★
Richard B - April 27, 2025
Verified Purchase
Easy Repair
The part worked great....
★★★★★
★★★★★
Michael J - December 17, 2022
Verified Purchase
As described as fast delivery
I have yet to install the parts. I have them as a backup as it is usually a part that needs replacing every few years. The parts seem to be as described. Great install videos and fast delivery!
★★★★★
★★★★★
Donald Lee G - May 7, 2020
Verified Purchase
Replace was easy than thought. Part was great fit just like factory
The help on percentage of parts as to problem helped a great deal
★★★★★
★★★★★
Sandy J - July 23, 2021
Verified Purchase
Just what we needed
Just what we needed
★★★★★
★★★★★
John P - July 26, 2023
Verified Purchase
Just as needed
The part was exactly as shown and works perfectly. I have bought all my appliance parts from these folks in the past and will continue to do so in the future.
★★★★★
★★★★★
Eddie M - October 31, 2022
Verified Purchase
What I needed...
My washer is back to work. The part was what I needed, at a decent price. The part came relatively quickly through regular shipping, easy quick repair.
★★★★★
★★★★★
Scott B - April 16, 2020
Verified Purchase
worked as expected
the part came fast and was the correct part
< Prev
1
2
Next >
Installation Instructions
Average Repair Rating: 3.2 / 5.0, 11 reviews.
What's this?
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Washer would not step through the cycle steps, would not complete the washer cycle.
Per the instructions on the website, I: 1. Disconnected AC Power, turned off the water supply and disconnected the water and drain hoses from the rear of the washer. 2. Laid the washer front side down to access the bottom of the washer. 3. Remove the Pulley Guard ( 2 nuts.) 4. Removed the Shift Actuator Assembly (2
... Read more philips screws.) 5. Disconnected the electrical connector from the assembly. 6. Remove faulty Actuator and replace with replacement part. 7. Install the Pulley cover lift washer upright, reconnect water supply hoses and drain tubing, plug washer in and tested.
Problem is resolved, saved almost $250 by doing it myself!
Read less
Walter from CLAYTON, NC
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer would go from sense to done without running cycles. Sometimes the drum would make a quarter turn.
I followed the video published on this site
Michael from Cranford, NJ
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
2 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Would not start to spin on spin cycle.It would just make a clicking sound
Tipped washer on its back & tookold Washer pulley assembly off & put new one on.
Tip washer on its front removed belt guard and belt. Removed shift actuator. Put new actuator on, put belt and guard back on, put back panels on and it was fixed.
Jerry from LENGBY, MN
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
3 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
F7 e1 code
Thought we needed a new shift actuator but after getting the parts and starting the replacement noticed the capacitor had come loose and was banging around under the washer. Found there was a little wire to the shift actuator that was cut probable from the capacitor being loose. spliced the wire back together and replaced the capacitor b
... Read moreut not the shift actuator and its been working great. was an easy fix and easy to get to. Didn't need the maytag man when we can get parts from here.
Washing machine would not spin clothes, little to no agitation
Our 5 year old Kenmore washing machine broke. The first symptom was that the clothes would come out completely wet. This was due to no spin cycle. The second symptom was that the washing machine had little to no agitation. The lid still locked shut, there was no odor, and you could hear the machine running.
In the event a machi
... Read morene does not agitate or spin, the diagnostics on this website will lead you to believe that drive hub assembly or shift actuator is the problem. The drive hub assembly is by far the more common repair (the pieces are made of plastic and are designed to wear out). If you are torn, go with the drive hub kit repair. That's what it was.
There were some surprises after carefully watching the how to video. First, the agitator in my machine was very tall and required a socket wrench extension to reach the drive hub nut. This will require two sets of hands. Second, the drive hub nut was stuck to the point where I nearly gave up. WD-40 and degreaser did not work to loosen. I ended up pouring a half teaspoon of powdered soap onto the stuck nut to get more grip on the nut. This, along with two sets of hands, got it loose. Third, calibrating machine was barely touched on in the video but this is extremely difficult, the instructions that come with the part were insufficient, and the videos on the internet are not that good. In the end, I'm not sure that the machine ever calibrated. In essence, the machine is re-calibrated by turning the switch in a specific sequence of right to left. Lights are then supposed to flash. This never did anything. I ended up opening and shutting the lid 10 times in 10 seconds as this was allegedly a way to recalibrate.
Note: 2018 and later washing machines suck because of California and the federal government rules and pressure to make them "green". Well, they don't work that well anymore as a result. Keep this in mind when you vote.
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
12 of 13 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Agitator would not spin, causing when tried to shift into high speed spin. It would cause tub to go out of balance.
First had to take the top of the agitator off to expose the bolt down at the bottom of the agitator. Take a ratchet with 2 1/2 extensions to get bolt off had problems so I had to use impact gun. pull agitator straight up, was stuck a little bit, but once she giving her a few tugs, it popped off the hub. On top of the hub, there is a keywa
... Read morey. Use a straight screwdriver and tap it out sideways. Then remove six Phillips screws and the hub pulls out. Clean the splines really good before you put new hub in. Slide new hub in put six screws in. Tighten them down evenly. Put new keyway back in slide agitator back onto shaft. Bolt on,tighten down Bolt, put top agitator back on. Replacing shift actuator tilt washer up so you can get to the bottom side take a nut driver. There’s two screws on the shield remove them that exposes the shift actuator on the side of the transmission. Remove the harness there’s a clip you push and pull straight out and there’s two screws I believe they’re Phillips And it pulls straight down put new one up in there put the two screws back in make sure the plastic tab on the shift actuator went into the tab of the transmission replaced the wire harness, push it back in make sure it snaps in put shield back on,the two screws in,and you are ready. Once you have those parts back on, you have to reset the washer instructions in your manual. It tells you how to do it. you have to do this or your washer will not work properly.
Washer won’t go into spin cycle! Tries too but then stops
Replaced the drive belt and shift actuator but that did not fix the problem! So I ordered a transmission and this still did not fix it! I give up! Time to get a new washer!
After removal of wash plate bolt. Apply Liquid Wrench oil to wash plate spline shaft. Give time for oil to penetrate. In the time it took to disassemble the motor and gearbox the oil had worked. Give the wash plate a good knock with a rubber mallet several times. After that I was able to wiggle off the wash plate by hand without breaking
... Read moreanything. Be sure to pull straight up on the wash plate, any twisting or torquing will bind the spline and the wash plate wont move. The PartSelect YouTube video was perfect for the other parts of the repair.
Ask our experts a question about this part and we'll get back to you as soon as possible!
40 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Frank
March 4, 2018
Hello,i have already replced the clutch assembly because it was making terrible howling noise. Noise is gone but now it wont spin the tub. When the spin cycle starts, it sounds like it wants to spin but then it makes a high speed rubbing noise. I took the lid lock off of the lid and inserted it into the lid lock switch to see what is going on during the spin cycle. I saw the impeller spins up fast for a few seconds and the tub appears to start spinning due to friction, but then it all stops, 30 seconds later it starts again and does the same thing. The tub never gets spinning under power, just friction.
For model number MVWC555DW1
Hello Frank, thank you for your question. I would recommend checking the ACTUATOR part number W10913953, and GEARCASE part number W10771760. If the unit is not spinning, but working otherwise the issue is probably the actuator part. I hope this helps!
21 people found this helpful.
Did this question help you?
Thank you for voting!
Patty
January 4, 2019
Hello the other day while i was doing laundry my centennial was getting ready to go to the rinse cycle and agitate when it made this loud noise kind of like metal on metal sound and now will not agitate during the wash or rinse cycles but spins just fine. Conveniently my washer isn't covered by may tags so called 10 year replacement warranty they want me to pay 125.00 for a repair man just to diagnose my machine if i would have known that may tag is no longer american made but now comes from china i think i definitely would have bought a different machine please help me with this problem thanks ever so much
For model number MVWC415EW1
Hello Patty, thank you for your question. We would recommend checking the clutch part number W10721967, and the actuator part number W10913953. It sounds like the clutch broke and now the unit will not go from spin into agitate mode. Both of the above mentioned parts help to agitate the unit. I hope this helps!
10 people found this helpful.
Did this question help you?
Thank you for voting!
Carlos
July 9, 2019
How do i test a actuator
For model number wtw5000dw0
Hello Carlos, thank you for your question. Unfortunately, we do not have any information on testing that part. However, if the unit isn't shifting between agitate and spin, if the washer is not washing properly, clothing still soaking wet, will not agitate, burning smell, will not drain, unusual noises, pumps but will not spin the actuator may be faulty. I hope this helps!
8 people found this helpful.
Did this question help you?
Thank you for voting!
Roger Nash
January 25, 2018
It does not spin at the end of the wash. It washes and drains.
For model number ATW4676BQ1
Hello Roger, Thank you for your inquiry. We would recommend checking the following parts to fix your issue: shift actuator, lid latch assembly, drive belt, clutch assembly, and the gear case. You can test the parts with a multimeter. If you are unfamiliar with how a multimeter functions, there are YouTube videos available to assist you. Hope this helps!
5 people found this helpful.
Did this question help you?
Thank you for voting!
Vickie
October 2, 2019
My washer takes a long time to go from sensing to wash to rinse to spin. When it does move to the next cycle it does not agitate or spin it make a noise, stops, tries again 3 times to advance to next cycle still making a noise. Then the noise stops and after about 30 minutes the washer will move to next cycle drain, fill up and then starts the noise again for 3 tries to advance,there is still no agitating or spinning. The lock on the wash is engaged. Please help.
For model number WTW5000DW0
Hello Vickie, thank you for your question. We would recommend checking the clutch part number W10721967, and the actuator part number W10913953. It sounds like the clutch broke and now the unit will not go from spin into agitate mode. Both of the above mentioned parts help to agitate the unit and switch between cycles. I hope this helps!
5 people found this helpful.
Did this question help you?
Thank you for voting!
Tim
May 23, 2019
My washer will spin but not agitate. What parts do i need to repair? Series 500 Kenmore
For model number 110.25132411
Hi Tim, thank you for your question. There are a few parts to check when your appliance is not agitating. You should take a look at your driver pulley, and your belt first. If those parts are fine then you may need to look into your actuator being the issue. I hope that helps. Good luck with your repair.
4 people found this helpful.
Did this question help you?
Thank you for voting!
Christopher
February 7, 2020
My Whirlpool washer will agitate just fine during a normal wash, but it does nothing at the spin cycle. When i select "drain & spin" only, it will drain and spin just fine. Could it be the actuator? The lid locks and the indicator led shows it locked as well during the spin.
For model number wtw4815ewo
Hi Christopher. It is possible it could be the actuator. Thank you for your question and good luck with your repair.
4 people found this helpful.
Did this question help you?
Thank you for voting!
Debbie
February 14, 2023
Why is our washer shaking, moving all over the place when spinning? It vibrates and makes so much noise it sounds like a tornado.
For model number WTW4955HW1
Hi Debbie,
Thank you for your question. If your washer shakes and moves, there are some parts that you will need to check to see which one is causing the issue. You will need to check the suspension rods and springs, the tub ring, the tub wear pads, the drive hub kit and the drive pulley. We have included some links from our website that you may reference on how to check these parts. Once you have determined the part you need, please call customer service. We look forward to hearing from you!
My Maytag commercial washer is not washing just sensing mode sometimes rinse and lid don't lock either
For model number Mvwc416fw0
Hello Rudy, Thank you for contacting us. I suggest checking the following parts: PS11727984 Lid Lock Latch Assembly, PS11747978 Drive Belt, and PS10057144 Washer Drive Pulley. Good luck with your repair!
3 people found this helpful.
Did this question help you?
Thank you for voting!
Maurice
September 9, 2019
The washing machine will not agitate or spin out the water. Do you think it is the actuator, if so can the part be tested? Thanks
For model number ntw4605ew0
Hi Maurice, thank you for your question. If your appliance will not spin or agitate, you may want to look at your belt, drive pulley, door lock, and your actuator for being the issue. You can generally test most parts with a multi meter. Here is a video that will show you how to use one: https://www.youtube.com/watch?v=bWC44fHn0As. Good luck with your repair.
2 people found this helpful.
Did this question help you?
Thank you for voting!
< Prev
1
2
3
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Item is in stock and is estimated to be delivered in 2-3 business days via Standard Shipping.
On Order
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Special Order
Item is not in stock and usually ships 10-15 business days from the time you place your order.
NLA - No Longer Available
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Washer","title":"Washer","url":"/Washer-Parts.htm"},{"position":2,"name":"Transmission or Clutch","title":"Transmission or Clutch","url":"/Washer-Transmissions-and-Clutches.htm"},{"position":3,"name":"W10913953","title":"W10913953","url":""}]
You added 1 item to your cart
✖
% OFF
$
$
Qty:
Total item(s) in cart:
Order Subtotal
$
*Taxes and shipping will be applied during checkout
