WCSR2090DCCC General Electric Washer - Instructions

I removed the front cover, then unscrewed the top to expose the top. There are two screws that hold each strap, which turns out are different sizes, so I had to use two different sockets. I also had to remove the hose & plastic tube for the bleach. Once that was done, the replacement was easy, I replaced all 4 straps, reconnected the tube for the bleach, screwed the top back on and snapped the front cover into place. This took maybe 30 minutes - and I am female!

I replaced the old knob with a new one.

After realizing I had purchased a used washing machine without a drain hose I thought I would never find one, but then I found partselect.com. After easily locating the part on the web site from the detailed diagrams and model number I then ordered it. Receiving the part quickly I used a socket to remove the plastic connector that prevents the hose from disconnecting once the washer is turned on. I fed the hose through the plastic connector and into the drain hole without any issues. I then used my one small socket to secruely fasten it back together. There was no additional tools or items needed to successfully attach the washer drain hose.

I wasn't sure what the problem was. I Googled the most common problem for this washer and it pointed to the Lid Switch with Wire Harness. I ordered the part, watched the video provided, and installed it. Installation was just like the video said. Due to the lack of dexterity in my hands due to arthritis, it took about 25 minutes from start to finish. Washer works like new now.

Basically, I just followed the instructions in the video that is posted on this sight. It went off without a hitch. Removed the screws from the control panel, lifted it up and out of the way. Then I used the putty knife to release the clips that hold the front panel in place and then removed the top of the washer. Pretty easy from there to swap out the dampening straps and reassemble the washer. Saved a lot of money doing it myself.

Reviewed your website for problem symptoms for top loading washers not agitating and possible solutions. Purchased the lid switch wiring harness. All I needed was a painters 1" putty knife, wire cutters, Philips head screwdriver, (2) electrical connectors (crimping type), crimping tool, and electrical tape. Very easy installation and problem was solved. Recommendation, the wiring harness should come with electrical connectors (crimping type). The installation video on your website was a big plus in making this small project a success

Drain tub. remove 2 hose clamps and hoses. R&R 2 screws that hold pump.

Took front panel off the washer and found the pump working but no water drained from the tub. Took the motor off the washer by removing the two 10mm screws and attaching hoses. Decided to take the motor apart and found the propeller shaft has broken off inside the pump. Ordered new motor from Partselect and replaced it. Washer is working fine now.

It was almost a complete tear down. Most difficult part was discivering how to remove the front panel. Slip a putty knife between the top and front covers. push and depress the spring tab on each side. The left hand nut on the hub was difficult. I had to get a neighbor to hold a large pair of pliers while I put a pipe wrench on the nut and hit it with a 2 lb. hammer in order to break it loose. Puting it back together do not forget to reconnect the level sensing hose to the level selector, I did. Machine will not perform without it. You can do it! I did.

Tub seal was found completely broken. Replaced it.
Then replaced tub bearing, tub bearing washer, shaft & mode shifter assembly and 6-rib drive belt.
Reassembled and tried, more quieter and like new machine.

Loosening tub nut was a challenge as it was bit corroded, use of WD40 was a great help.
Knowledge from you tube was a great help.

We pulled up diagrams online and read a lot about the repairs. Four screws on top took off the electrical panel. Two clips hidden under the front of the top panel released the front panel. We followed the clear tube up to the water level pressure switch. We disconnected the previous switch, and connected the new one, one wire at a time. We tested and found that the water now stopped filling. Put the washer back together - done! Cost - $30 and 1/2 a hour total vs. calling a repair person.

The first attempt to fix the problem did not turn out so well. I replaced the tub bearing, split ring, tub bearing washer and the hub washer. After reassembly and testing, the loud airplane noise was still present during the spin cycle
Then I ordered and replaced the mode shifter shaft assembly and, since I was going to disassemble again, also ordered a new 6-rib belt. Once reassembled and tested, it was quieter than when it was when brand new, according to my wife.
Parts came in very quickly and the tutorials/youtubes were spot on.

watched the video, and it was simple!

Open back cover and found that drain pump had a bad seal. Took it apart and bought new seal some what same size. Put everything togather and start washing clothers and wife complained that it became wost the before. When on line and found pump and price was just right to take a risk. Ordered on sunday and got ups tuesday.
Replaced pump on Sunday and leak was gone and wife was happy.

------Got chicken and beer that Sunday--------------

The hose has a tapered end that fits in a tapered hole in the back of the washing machine.When insalled the first time,the joint leaked badly.My solution was to coat the hose end and the interior of the hole in the back of the washing machine with silicon sealant;let it set up for a few minutes and install the new hose.This solved the leak and the hose seems to be working fine now.