WCSR2090DBWW General Electric Washer - Instructions

Followed video on You tube that showed step by step how to compete repair.
The machine used in video was brand new and there was no corrosion on any parts so disassembly was much easier in video than on 9 year old machine.
Also reinstalling drive belt was a little tedious but overall job very straightforward and resulted in positive improvements in performance and greatly reduced noise levels.

My son repaired the washer . It was really easy to fix. He had it working in about 15 minutes. Thanks to PartSelect's fast delivery service I was only without my washer 2 days.

I removed the old knob (very easy, used a flathead screwdriver to remove the clip and off it came). Put the new knob and clip on and voila!!!! It worked. My local appliance people wanted over $100.00 for the same part. Definately using Parts Select if issues arise in the future.

We pulled off the bottom cover to access the pump. The washer was on its back and that made it easier to reach. There was two hose clamps to pull off along with the two electrical parts. Very easy to replace.

simply pulled the old one off with the broken clip and pushed the new one on. This is the third or fourth time we have used Parts Select and have always gotten the best service and best price.

Removed knob by using screwdriver to pry out plastic retainer. Put new knob on the timer. Took about 5 minutes. The problem was caused by the wearing out of the teeth on the knob.

1.Pulled the agitator out. Unscrewed the top nut, which was a little tricky to break loose since it had been in place for over 10 years. Pulled out the entire washing cylinder to unscrew and replace the hub. Not bad but you need to take out the inner tub and that requires doing a little extra unscrewing and prying.

I removed agitator by pulling it up until it unsnaped.

I removed the old agitator coupling by removing the bolt and pulling up while twisting it.

The new coupling looks different than the old part but fits the same.

I pressed the new coupler on to the agitator shaft, reinstalled bolt and pressed agitator on the agitator coupler until it snaped into place.

Washer runs like new!

First buy the tub nut wrench. I can't over emphasize that! $12 at amazon. With out it getting the inner tub out will be the worst part of the job. And you will have to buy a new nut. I had trouble getting the old bearing out of the outer tub. I had to drive it out with a punch. The only other problem I had was after getting everything back together the new tub seal leaked. When I installed it if fit very loose on the OD. I ordered a new seal hoping it would fit tighter but it didn't so I coated the the seat of the tub and the OD of the seal with gasket shellac. That solved the problem. Working great.

Problem was intermittent. It would happen once a month or so. Eventually I set next to the machine and kept turning it On and OFF through cycles for about a half an hour until it failed and I was able to confirm that problem was with the water valve.

Buying and replacing the water valve was easy.

WARNING: UNPLUG THE WASHING MACHINE FROM THE WALL BEFORE ATEMPTING ANY ELECTRICAL WORK ON YOUR WASHING MACHINE!

I watched the video from the web site and the one that came with my invoice. This made it very easy to fix.I got the tools that I needed and went to town on the repair.

Our GE washer stopped agitating. We bought us a Whirlpool Cabrio washer with auto-sensing and an impeller instead of an agitator. My wife couldn't get used to washing clothes with so little water. We found out about PartSelect.com and ordered the part they indicated would probably fix our GE washer ($5.86) - the Agitator Coupling Kit. Ordered it on Friday, received it by Fed Ex the following Tuesday. It was an easy installation. Our GE is working fine. Took the Whirlpool back to the store, got our $637.00 back.I plan to use PartSelect.com again,if I need to. We don't like the new type washers as well as our 7-1/2 year old GE.

After doing some troubleshooting, I found that the Air Bell was stripped inside.

First I removed the agitator by firmly pulling it straight up. Then I removed the bolt holding the air bell (agitator coupling) with a ratchet. Then came the hard part. The air bell (agitator coupling) was stuck on the shaft and would not come off. I used rope to lasso under the coupling and tied it to a 2x4 for leverage and eventually wrestled it off by using an upward jolting motion time and time again. Spraying WD-40 in the coupling seemed to help loosen it up.

Prior to installation, I cleaned the grooves of the shaft by scraping them out with a flat tip screw driver. Installed the new coupling by tapping it down with a hammer until it was seated firmly and locked it down with the new bolt. Aligned the agitator and slid it down until it latched. Done!

I ordered the part on Wednesday didn't think we would be washing any clothes until atleast Monday. The pump came on Friday! Installed it 15-25 minutes(that's taking out the old one too) . As someone stated before the only (little) problem was the spring clamps. Screw the pump in first and then put the Clamps on.

Line up knob. Push on.