This is a replacement timer knob for your washing machine. To complete this repair you will need a pair of needle nose pliers. Turn off power to the washer before you start. Pull off the timer knob and use your pliers to remove the retaining clip. The new knob will already have a clip in place. Line up the knob opening with the shaft and slide it on.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
David P - May 23, 2024
Verified Purchase
Got part, fixed in a jiffy!
Washer knob needed a fix. Looked up part on partselect.com, BAM! They had it. Ordered it up. When it arrived in a timely manner, I replaced part as easy as pie!
Thank you, partselect.com
★★★★★
★★★★★
Michael D - December 21, 2023
Verified Purchase
East gix
Part came quickly. The fix was easy.
★★★★★
★★★★★
Susan T - November 27, 2022
Verified Purchase
Easy install
This part was exactly what I needed. I put in our machine model and looked at the diagrams to figure out what number part I needed. Then I ordered it, it came fast, and was super easy to install.
★★★★★
★★★★★
Nancy W - May 8, 2022
Verified Purchase
Super Easy
The knob arrived quickly and preassembled. It clicked right into place-couldn’t have been easier!
★★★★★
★★★★★
Elizabeth E - August 6, 2021
Verified Purchase
Easy fix
I was not sure I could replace this nob myself but it was worth a try. I received the part in a few days and watched the video and voila. I repaired my 14 year old washer. And I did not need my son to come over and take care of it for me
★★★★★
★★★★★
Miguel T - June 4, 2021
Verified Purchase
Easy repair.
The part came fast and in good condition, easy to install, my machine is working like new.
★★★★★
★★★★★
Kelly M - February 13, 2021
Verified Purchase
Perfect ??
Had bought a control knob at a parts store nope wrong one! Ordered from here part fit perfectly ??
★★★★★
★★★★★
Barbara G - January 27, 2021
Verified Purchase
Part was excellent and went on easily. My washer us like brand new again.
The part I ordered was exactly what I needed to get my washer back up and running. I could not believe how fast I received the part. Absolutely fantastic service. I have already told my family and friends about this company and I highly recommend them.
★★★★★
★★★★★
Helen K - January 19, 2021
Verified Purchase
Great, prompt service!
We ordered a new knob for our washing machine and it arrived promptly so we were able to do a minor repair without the cost of hiring a professional.
★★★★★
★★★★★
ANTHONY S - January 7, 2021
Verified Purchase
Exactly what i needed
Was the exact part i needed. Easy repair. Came with everything i needed
< Prev
1
2
3
Next >
Customer Repair Stories
Average Repair Rating: 4.6 / 5.0, 80 reviews.
What's this?
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Timer knob failed to engage and rotate dial
This is a very easy repair. I followed the video instructions for the timer and knob. The basic steps are: 1. Unplug appliance and move it away from wall for access to back. 2. Remove three hex head screws behind control panel/ 3. Tilt control panel forward and slide it sideways to free it from the washing machine.
... Read more>4. Remove knob using a flat head screw driver to slide retaining clip 5. Disconnect electrical harness from timer assembly. 6. Remove one screw holding timer to control panel and rotate the timer assembly to remove it. 7. Install and connect new timer. 8. Complete installation by re-installing knob, panel screws, etc. Very easy.
Took out the 3 screws holding the back on and removed the back. Unplugged the timer, took off the knob and dial. Removed the old timer. Replaced with the new timer, replaced the screws holding the timer in. Put the new dial and timer knob. Replaced the back tightened the screws and started the washer up. Yeah!
I watched the instruction video on your site to install a knob and clip on a GE washer. It was very helpful. Installation was very quick,less than 15 minutes.
I followed the easy instructions on the video site for installing a knob and clip on a GE washer. The knob and clip were not available to find locally. I was told at a part store that a whole new operating switch had to be replaced which would be approximately $180 to buy. After visiting your site, and viewing your easy instructions, on
... Read morely a knob and clip were needed. Delivery was in 3 days. Very easy installation. Saved bucks. Pleasant experience.
Read less
JANE from Solvay, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Knob and Clip for Washer
I took of the old clip an broken piece of the knob, and removed the selection plate, and push on the new knob and clip, using my pliers.
Berecia from WEST PALM BCH, FL
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bad timer and belt
Removed screws from the back removed screw from timer replaced timer. Removed front panel and replaced belt videos were extremely helpful
Followed videos on partselect.com for changing tub bearing. Video does very good job of showing steps required. Repair would be easy if washer was new. First problem was conical tub nut could not be loosened even applying penetrating oil and heat. Finally resorted to 1/2" drive pneumatic impact gun (wrench) which hammered about 10 sec
... Read moreonds before the nut came loose. Had to purchase 1-11/16 deep well 6 point impact socket at cost of about $30 for this task. Second difficulty was removing tub seal whose exterior rubber coating had apparently failed and the seal internal metal parts corroded causing it to expand. The tub seal had to be beat out from the bottom side using a drift. The next difficulty was removing the tub bearing which had corroded from minor leakage through the tub seal. Corrosion made the tub bearing outside diameter (OD) larger so it could not be removed using the method in the video. The outer tub bottom side was supported as close to the center as best possible and a socket just smaller than the tub bearing OD was placed on top of the bearing and was used to drive (hammer) the tub bearing out. There was a lot of cleaning necessary especially on the inner tub conical fit areas where tub rides on the split ring and hub nut. During reassembly the tub seal did not have a press fit into the tub; it was barely finger tight. I suspect the tub had permanently distorted in the seal area because the old tub seal had corroded and expanded. So silicone sealant was applied to the outside diameter of the tub seal to assure no leakage around the seal. I allowed that to cure overnight to be certain the seal would not move when inserting the shaft and mode shifter through the seal. A very light oil was applied inside the tub bearing. The last problem found was when tightening the bolts holding the base frame to the outer tub the base frame was pulled to one side so the mode shifter was not concentric with the base frame. This would place a side load on the mode shifter shaft and tub bearing. This was resolved by placing a 1/16" thick washer between one leg of the tub and base frame which maintained the base frame concentric to the mode shifter as the tub to base frame bolts were tightened. The repair is conceptually easy to perform but was challenging due to corrosion and detergent residue from 11 years operation. Now the washer rotating parts are essentially new, the repaired assembly is probably better than the original factory assembly, and the washer should operate for another ten years before the mode shifter bearing goes out again. A longer repair than anticipated but time and money well spent. Being retired helps.
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
3 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
multiple parts were needed to repair my washer
Initially I thought just the timer knob would take care of my washer not working, but that was too naive of me, lol. I had to replace the timer knob & clip, the compression dial and the agitator and the agitator coupling. In other words I rebuilt my washer using the installation video's provided here. I now have a "bra
... Read morend new" washing machine for a total of less than$100 and it is working perfectly!
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
6 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Rebecca
January 31, 2019
Hello!!
the outer knob will not spin the dial to start the machine. i have to manually turn the dial ring then push down the timer knob to get the washing machine to start. do i need to replace the knob or could it just be the clip?
thanks!!!
For model number WLSR2200JW33
Hello Rebecca, thank you for your question. You can check the clip to see if it is loose or broken. However, the best thing to do would be to replace the timer knob PartSelect Number PS1482286 which comes with a new clip. I hope this helps!
19 people found this helpful.
Was this helpful?
Thank you for voting!
Ron
May 1, 2019
When I push in timer knob it doesn’t engage. It just spins around when you turn it. Could you tell me what part or parts i need? Thank you.
For model number GHWP1000M2WW
Hello Ron, Thank you for the question. If there is no visible damage to the knob or dial, I suggest replacing the Timer Switch, PartSelect Number PS3506805. Thank you for your inquiry, good luck with this repair!
Hello James, Thank you for the question. Very sorry but the eno20a 175d 3296 is not a valid number. In order for us to locate the correct parts and repair information we will require the model number of the unit. Once you have located the model number please feel free to resubmit the question and we will be happy to help you. Look forward to hearing from you!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Clark
December 2, 2019
When i removed the broken timer control knob, the spindle it attaches to came out in the knob. How is the spindle replaced or re-attached? Thanks.
For model number WJRR4170GWW
Hello Clark,
Thank you for your question. The spindle cannot be reattached, you would need to replace it by replacing the timer switch for your model under part PS1482380 to fix the issue. Hope this helps!
GE washing machines works but i have to advance the cycles myself. How will i know if it's the entire timer or just the knob that needs to be replaced?
For model number WDRR2500K4WW
Hello Maribel, thank you for your question. If you have to advance the cycles yourself, the timer should be replaced. That is PartSelect Number: PS3406192. Please enter the part number into the site for current price and availability. Good luck with your repair!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Delois
June 27, 2023
my washer want come on plus it stop in the middle of a wash what you think that is
For model number GCWP1800D1WW
Hi Delois, thank you for reaching out. Based on our understanding of the issue, we would suggest you replace the timer, part number PS4704240, to fix the issue. We hope this solves your problem.
