GCA24KBBAFSS General Electric Refrigerator - Instructions

snapped the old one out snapped the new one in.

i followed all the other submited solutions. really easy. popped out the broken light switch with thin tip screwdriver. careful not to let wires slip into compartment. then attached wires as i pulled them off broken switch. then carefully pop the new switch back in the slot. when i was younger i worked for an appliance repair company. i felt confident in this repair.

Ordered the part and within three working days the part was delivered. It took two minutes to pry off the broken part and one minute to snap in the new one.

replaced with new one

Unplugged the refrigerator first....then on the inside of the fridge, I popped the temp sensor cover off (upper LH side) and exposed the old sensor. I snipped off the old sensor about 3" down from the end and connected the new sensor (which I trimmed down to about 3" long) with some heat shrink wire nuts/connectors. Let the fridge run for a day or so and confirmed the problem was solved! Oh yeah, there was no way to tell the 2 wires apart (power vs. ground) on the sensor. However there was a manufacturer's stamp on the wires. So note the orientation of the text and mark one of the wires with a sharpie on both the old and new sensor before trimming. This will give you a reference for which wires to connect when adding the new sensor to the old wires.

It really was as simple as the other folks noted. Slid a screwdriver into the edge of the broken switch and it popped right out. Disconnected and reconnected each of the two wires and just slid the switch back into the slot. Truly a DIY fix.

Replaced light switch. Defrost cycle remains suspect but refrigerator has worked OK for about 10 days.

Things fall out of my refrigerator frequently thus the broken lite switch. Thought tape would solve until new part arrived. Thank goodness part came the next day as even with tape on and door close and light bulbs removed fridge read door as open and would not cool It is programmed not to run with door open. Within 24 hours part was delivered, unbelievable . It was that fast. Easy insertion and plugged in to the wiring and my refridge once more recognized the door was shut and began cooling. Thanks again

The repair is a snap, you can watch the video and it will put you on the right path. My story is more about the service that Part Select gave me. I used a small box fan on low as a temporary fix. My model number was worn off from the box wine we store in that particular place. So I ordered the part based on looks, well it was wrong. Called Part Select and we talked, the nice lady on the other end said OH it must be this fan motor. Send us back that one, and I'll get this out too you. I'll credit your account for $7.99, and it cost me $8.99 to ship back the wrong part. Wow, the next day I received the new motor. They sent it overnight! I thought it would be 5-6 days! Unbelievable. I will use this company for any, and all my repairs.

Pried the switch on the bottom with a flathead screwdriver, twisted it and the switch came out far enough to take it out by hand. The bottom of the switch has to be raised upward a little because the connectors are on top of the switch. Changed the wires from the old switch to the new one, one at a time. Insert the new switch. Saved a repair call, and probably a more expensive switch. Less then 15 minutes.

changed sensors did not repair problem,replaced damper with mechanical damper fixed problem.

took out shelves and removed the back plate my removing 2 screws with a nutdriver.removed the old defrost timer and defrost heater which was really easy.then installed the new ones.the video i watched on the website was really helpfull.

remove the Ice tray, remove hex bolts from ice tray hangers on side of freezer. unscrew ice maker and remove it. Remove ice tray auger motor assembaly (4 hex bolts) remove 2 more hex bolts from top of rear inside panel. remove 4 hex bolts from lower panel as well. now with lower section out, you should see the last 2 hex bolts holding on plastic shield (top section rear panel) un screw light cover. Squeeze light fixture and push in. now remove entire top section of panel. All will be exposed. Remove old motor housing, disconnect wires, remove clip from coils. (NEW MOTOR DOES NOT HAVE CLIP OR WIRE FOR COILS)Attatch new motor and replace grommits. Reverse instructions for re installation.

Little difficult getting the switch out, had to pry wth some force. New installation was real easy.

Replaced all the sensors in both the feezer and refrigerator.Even though it colder now it still is not cold enough.Freezer won't freeze items but is cold and refrigerator still not real cold