EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

GCA24KBBAFSS General Electric Refrigerator - Overview

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Temperature Sensor – Part Number: WR55X10025
$30.53
In Stock
Temperature Sensor
★★★★★
★★★★★
(69)
Part #WR55X10025
This sensor (Temperature Sensor, Thermistor, Refrigerator Temperature Sensor) sends the temperature reading of the compartment to the control board. If you notice your refrigerator is too warm, too cold, or not defrosting properly, then there may be a problem with your sensor. The temperature sensor can break from material fatigue or through normal use, and should be replaced. It is attached to the evaporator and control housing in your appliance. It measures approximately 1.25 inches long with 18 inch wire leads, and is constructed out of plastic. This part comes in white, beige. It includes the sensor, with wire leads.
Evaporator Fan Grommet - Red – Part Number: WR02X12008
$13.92
In Stock
Evaporator Fan Grommet - Red
★★★★★
★★★★★
(27)
Part #WR02X12008
If you notice that your refrigerator or freezer is noisy or too warm, you may need to replace the evaporator fan grommet. This part is red in color, and is about 1 inch in diameter. The evaporator fan grommet is located behind the evaporator fan cover in the back of the freezer. You will need to remove the evaporator fan cover to access the evaporator fan and complete this repair. Before you begin this repair, ensure the power to the refrigerator is disconnected. You will need a pair of needle nose pliers, a small flat blade screw driver and both a 1/4 and 5/16-inch nut driver to complete this repair.
Module Shelf Insert – Part Number: WR71X10764
$56.96
In Stock
Module Shelf Insert
★★★★★
★★★★★
(65)
Part #WR71X10764
This shelf insert is a genuine OEM replacement part for your refrigerator. The shelf insert can be installed without any tools. Simply pull out the existing shelf and insert the new one.
REFRIGERATOR DOOR LIGHT SWITCH – Part Number: WR23X31507
$18.37
In Stock
REFRIGERATOR DOOR LIGHT SWITCH
★★★★★
★★★★★
(41)
Part #WR23X31507
This is the light switch that goes in your refrigerator. If the light is not working or stays on, you may need to replace the switch. It is made of mainly white plastic, and is an OEM part, directly from the manufacturer. Be sure to disconnect the refrigerator from the power source before you begin this repair. To remove the switch, simply use a flathead screwdriver to pop the switch out from the refrigerator wall, then disconnect the wires. Reconnect the wires to the new switch, snap it into place, and the repair is complete.
Compression Ring – Part Number: WR02X12149
$16.05
In Stock
Compression Ring
★★★★★
★★★★★
(2)
Part #WR02X12149
This compression ring is meant to hold the evaporator fan motor in place in the freezer compartment of your refrigerator. This is is a genuine OEM part. The tools needed to complete this repair are a Phillips screw driver and small flat blade screw driver. Be sure to turn off your refrigerator before removing the evaporator fan cover so the fan does not turn on during repair. It is recommended to check the grommets, evaporator fan, and fan blades during repair in case they also need replacning. The compression ring may need replacing if the fan is noisy, or the refrigerator compartments are too warm. This part is sold individually.
Lid Bumper – Part Number: WR02X10540
$16.05
In Stock
Lid Bumper
★★★★★
★★★★★
(2)
Part #WR02X10540
The lid bumper or evaporator fan motor bumper in your refrigerator prevents the fan motor from scraping against the side bracket. If your refrigerator/freezer is noisy, the bumper could be worn down or missing, and the sound could be a result of the motor scraping the side bracket. You will find it between the fan motor and the side bracket on the evaporator fan motor assembly. To access the bumper, you will need to remove the evaporator fan motor assembly from the freezer. This part is made of orange rubber and is less than half an inch in diameter. It has a rounded top and a slightly pointed bottom, and is sold individually.
Refrigerator Door Shelf Bin – Part Number: WR71X10973
$109.26
In Stock
Refrigerator Door Shelf Bin
★★★★★
★★★★★
(41)
Part #WR71X10973
Sold individually. This door bin is for refrigerators. Door bin attaches to the inside of the refrigerator door and typically holds jars and bottles. Follow the instructions in the owner's manual for installing this part.
EVAPORATOR FAN BLADE – Part Number: WR60X30922
$78.38
In Stock
EVAPORATOR FAN BLADE
★★★★★
★★★★★
(9)
Part #WR60X30922
This evaporator fan blade is for your refrigerator, and it circulates air so that the temperature of the fridge is regulated. This model has 3 blades, and is a little more than 4 inches in diameter. It is made of white plastic and is sold individually. If your refrigerator is noisy and you hear a clicking sound, it is a good indication that the evaporator fan blade is warped or damaged. If the fridge or freezer sections become too warm, the fan could be to blame as well.
Shelf Stop - white – Part Number: WR02X10662
$21.94
In Stock
Shelf Stop - white
★★★★★
★★★★★
(8)
Part #WR02X10662
The shelf stop in your refrigerator is what locks the shelf into the refrigerator liner. The shelf stop can be found attached to the shelf. To remove the shelf stop, begin pulling the shelf out until the stop hits the refrigerator liner, then depress the shelf stop to remove the shelf. With the shelf removed, you can simply slide the old stop out of its groove, and replace it with a new one. This part is made of white plastic and is about 1 inch in length. It is sold individually, and is an OEM part sourced directly from the manufacturer.
Crisper Pan Front Gasket – Part Number: WR14X10059
$22.03
On Order
Crisper Pan Front Gasket
★★★★★
★★★★★
(13)
Part #WR14X10059
This part is a replacement pan cover gasket for your refrigerator. You will find the pan cover gasket on the meat pan, and it helps to seal the pan. If the pan cover gasket is lost or damaged, it will not be able to create the seal and will need to be replaced. The gasket is approximately 15 inches wide and is white in color. It is an OEM part from the manufacturer and is sold individually.
Evaporator Fan Grommet - Grey – Part Number: WR02X11331
$16.23
In Stock
Evaporator Fan Grommet - Grey
★★★★★
★★★★★
(4)
Part #WR02X11331
This is a replacement evaporator fan grommet for your refrigerator. The fan grommet absorbs the vibration from the evaporator fan motor for quiet operation while it runs. If your evaporator fan is unusually noisy, it could be because the grommet is damaged. This grommet is made of grey plastic and is approximately one inch in diameter. To access the fan grommet and complete this repair, you will need to remove the evaporator fan motor assembly. This part is sold individually.
Refrigerator Pan Cover – Part Number: WR01X10209
$21.90
In Stock
Refrigerator Pan Cover
★★★★★
★★★★★
(1)
Part #WR01X10209
Introduce a durable solution for your appliance repair needs with the GE Wheel Pan Cover. This robust piece has been engineered by the trusted brand, GE, to ensure long-lasting reliability. Excellently crafted to fit with precision, this part is perfect for renovation projects or maintenance jobs, guaranteeing a perfect fit. Boost the performance of your appliance instantly with this superior quality wheel pan cover. Easy to install, it's a must-have for all your do-it-yourself repair needs. Trust nothing but the best with GE.

Common Symptoms of the GCA24KBBAFSS

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Fridge too warm, evaporator icing up
606 of 738 people found this instruction helpful.
  • Gerald from San Clemente, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers
After replacing the defrost heater, main board and thermistor I still had the same problem. Called a repair guy and he (with the help of GE on the phone) diagnosed that the temperature sensor was bad. So I ordered from partselect and installed it and it fixed the problem. Been good for a couple months (knocking on wood). To install I had to cut the 2 wires to the old sensor, crimp the 2 new wires on and snap the new sensor to the clip on the evaporator. Very easy. Make sure you seal the ends of the wire crimps so moisture doesn't get in and corrode the connection.
Was this helpful?
Thank you for voting!
my refigerator was warm but the freezer was cold and working correcttly
302 of 399 people found this instruction helpful.
  • michele from North Smithfield, RI
  • Really Easy
  • 15 - 30 mins
  • Pliers
I went to a GE repair center to explain my problem, the service center reccomended that I have a techinician come out o look at it. $75.00 for the visit and what ever labor and materials wuld cost.

I went on line to see if there were others having this same problem and found that there were many with the same problem.
... Read more />After reading some of the ways that people found out what was wrong ...it became a matter of three components, the timer, heater or thermostat.

I tried the most common component and the less expensive one first , the thermostat switch I installed it very easily snipping two wires and attaching the news using wire nuts I used the diagram on this website to pinpoint the component and there has not been a problem since.
Was this helpful?
Thank you for voting!
refrigerator was getting too cold
149 of 218 people found this instruction helpful.
  • Larry from Menomonie, WI
  • A Bit Difficult
  • 15 - 30 mins
I removed the old temperature sensor by cutting the wires. I attached the wires of the new sensor with wire nuts and mounted it in the same bracket.
Was this helpful?
Thank you for voting!