405062 General Electric Dishwasher - Instructions

Popped the axle on to the wheel, then snapped it on to the lower drawer - done!

I am NOT handy, but my husband was gone when the wheels and stud/axles came. I was able to replace all of them in about ten minutes with no tools. Easy and no more frustrations!!!!!

I removed the old seal, cleaned behind it, and then put the new seal in. We saw a video on You Tube on how to do it. Partselect also sent instructions on a e mail with the order receipt. We enjoyed working with you guys. Your customer service representative was very nice and accurate in sending out the part. All went as she said it would. Thanks!!

Removed the old wheels and studs. Pressed on the new studs and wheels. Viola.

Unscrewed the old roller. But it was difficult to replace the roller as the rim of the roller would not fit into the slide mechanism and allow the screw to engage the hole. What I thought would be a 2 minute job turned out to be more like 20 minutes. I suspect there is a way to release the slide stop so that the top basket could be removed with its slide bar, but I did not see how to do that. I finally was able to "force" the screw into the hole

I installed new rollers and rack clips. The old ones had cracked and would not keep the rack in the tracks. I went to buy a new dishwasher which would have cost around $500. I bought $60 worth of parts although I probably could have just bought the clips for $15 and now the dishwasher is good to go! A real money saver.

I just had to play around with it to attach the new cap without breaking it.....never did this before but eureka! it worked.

The top right rail, facing the dishwasher, has a self lock tab. Using pliers, straighten the lock tab, insert the cap and then restore the lock tab to it's original position.

Water was leaking from under the GE dishwasher, but once we pulled it out, had apparently been going on for a little while. Turning the water off to the dishwasher made it stop, so it was happening even when the unit was not running, potentially indicating somewhere early in the path of the water to and into the machine.

Indeed, inspecting the water inlet vale showed a slow leak. Getting the replacement part was fine, and it fit the electrical, water inlet (existing 90-degree water inlet elbow), and water outlet connections just fine - but the original machine screws that held on the original water inlet valve did not work. It took a little research to figure out the new type of screw required, which was apparently a 10/16 Type AB, which seemed to be a less common type of sheet metal screw (with a point), as opposed to the original flat-ended machine screws. So, after ordering those separately (which were a bit expensive), it went together fine.

A note on the water inlet valve part just indicating the the threading on those parts has changed over time, so potentially ordering the screws to attach it might be worthwhile, would be good information to add about the water inlet valve.

Do not overlook the two screws on the bottom of the outer door panel.

So easy, even I was able to do it. Slide tabs back on defective basket and remove both sides, then slide the tabs onto new basket and place in dishwasher. All Done!

Used Phillips screwdriver to undo brackets that keep dishwasher in place. Pulled out dishwasher from underneath the counter. Placed hinge arm in spring, hooked spring onto clip, placed hinge arm in clip. Put back dishwasher under the counter and screwed in place. Took all of 15 minutes. Saved 185.00 for service call.

and figured that was the problem. After a call to a delightful young lady in your service department We concluded that these rollers were the only thing available. Dejected I went back to my project with the intent of removing the wheels and grinding them down BUT 1st I gave it one more try and after some careful alined--Presto they rolled into the 2 tracks. I snapped the end caps on tracks--Problems solved--Please note: if these parts were taken off of my Bill Please Recharge them to me.THANK YOU ALL (IT WORKS LIKED A NEW WASHER) RON TUCKER 302 449-0342

Repaired the soap dispenser.

Popped out Old Roller, put in new one, pushing it together with a pair of pliers.

My only regret is that i didn't check the other side of the dishwasher... the other roller was broken also, and now i have to pay 5.95 shipping & handling for a .29 cent item

Check all your rollers before you buy just one!!!!!