Kenmore Cooktop Wire Plugs and Connectors
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Kenmore Cooktop Wire Plugs and Connectors
Your Price
$16.24
In Stock
Kenmore Cooktop Terminal Block Kit
As far as the drawer glides they just snap into place Read more...
PartSelect Number PS470125
Manufacturer Part Number 5303935058
This part connects the wire harness to the surface element and is used for ranges. The kit includes interchangeable mounting brackets, ceramic wire nuts, heat shrink protective tubing, and wires. If your range/oven is having symptoms such as burner not heating, heating elements not working, burning smell, or if the oven is making a buzzing noise then this could be the solution. The tools needed to replace the kit are wire strippers, a heat gun or hair dryer, and #1 square heard screw driver. Refer to the installation/instructional video for further guidance to accurately replace the element.
Fixes these symptoms
- Element will not heat
- Oven not heating evenly
- Will Not Start
- See more...
Installation Instructions
Steven from Taylors, SC
rental property stove only had 2 working burners and bottom drawer off track
first i took out burners then i took out the screws of the termnal block bracket. i then raised the lid on the stoveand clipped the wires on all 4 of the terminal block kits.i then slipped the shrink wrap on wires and used the wire nuts to connect wires together then heated the shrink wrap. I then put screws back in terminal block brackets. I then put the burners on while looking under lid so i would know they were making good connections as this is a bad design from factory. if you pull out burners to clean them and they are not put back in right you dont have a good connection and that causes the terminal blocks to get hot and melt. thats what happened in my case. As far as the drawer glides they just snap into place Read more...
Your Price
$9.37
In Stock
Kenmore Cooktop Main Terminal Block Kit
PartSelect Number PS471605
Manufacturer Part Number 5304409888
Terminal block kits are also known as terminal boards, or terminal strips, and they are found in a wide variety of household appliances. Most often in ranges, wall ovens, and dryers. This kit attaches the power cord to the inner wiring of your appliance. If the terminal block is faulty, your appliance will not get the power it needs to operate properly. When removing the old block pay close attention to the wire placement, this will make installing your new part much easier. If you notice any of the wires or wire terminals are corroded or damaged they will also need to be replaced.
Fixes these symptoms
- Element will not heat
- Little to no heat when baking
- Little to no heat when broiling
- See more...
Installation Instructions
Timothy from Spring Valley, AL
Cord was not tightened enough by delivery crew.
PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.
Read more...
Your Price
$13.42
In Stock
Kenmore Cooktop Surface Burner Plug-In Block Kit
I ordered the parts on line early one morning, the next day they were at my door and installed that day, everything that I ordered was there, and fit properly.
Way to go Part Select.com
Jon Read more...
PartSelect Number PS340571
Manufacturer Part Number 330031
The surface burner plug-in block kit features a newer-style terminal block. This kit is designed for use with ranges and cooktops. This terminal block is how the coil element on your stove connects to the inner wiring of your appliance. Without this connection your burner element would not get the electrical current it needs to heat up. When your element will not heat at all, or if it is not heating properly it is likely an issue with the terminal block. You need to remove the element to replace this part. While you have the element out, inspect the element and the terminal for any corrosion, arcing, or discoloration. If you notice any damage to the element or the terminals we recommend you replace this part as well. This kit includes two metal brackets, two pre-crimped high-temperature wire leads, two ceramic wire nuts, two heat-shrinking insulators, and a mounting screw. Before you begin this repair, make sure you have unplugged your appliance.
Fixes these symptoms
- Element will not heat
- See more...
Installation Instructions
Jon from Oakley, CA
Surface elements quit working
Drilled out old and broken hold down clips, installed new ones(4). Cut old wires attached to surface plug in block, striped wires, and attached new plugin kit(4), warmed up heat shrink with a hair dryer, put in new drip bowels, the stove is like new.I ordered the parts on line early one morning, the next day they were at my door and installed that day, everything that I ordered was there, and fit properly.
Way to go Part Select.com
Jon Read more...
Your Price
$13.91
In Stock
Kenmore Cooktop Surface Burner Receptacle Kit
My sister's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts.
The element is working great now.
Whenever I need appliance parts again I'll use partselect.com. Read more...
PartSelect Number PS1570190
Manufacturer Part Number 12001676
The tools you will need to replace the surface burner receptacle kit on your range include a Phillips screw driver, and a pair of wire strippers. Before doing this repair, make sure to disconnect your appliance from the power supply and wear work gloves to protect your hands. The surface burner receptacle kit comes with a plastic block, high temperature wire nuts, a metal bracket, and wires. This part functions as the connection between the wire harness and the surface element in your range.
Fixes these symptoms
- Element will not heat
- Will Not Start
- See more...
Installation Instructions
Richard from Carthage, NC
Stove top element not working due to bad receptacle.
Turned off the power at the breaker box, cut the wires approximately 5 inches from the bad receptacle and removed it after removing one screw. Stripped back the wires about 1/2 inch and attached the new wires with the ceramic wire nuts provided and secured the receptacle back in place with the new screw provided in the kit.My sister's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts.
The element is working great now.
Whenever I need appliance parts again I'll use partselect.com. Read more...
Your Price
$31.61
In Stock
Kenmore Cooktop Surface Burner Terminal Block Kit
PartSelect Number PS242972
Manufacturer Part Number WB2X8228
Also known as receptacle.
Fixes these symptoms
- Element will not heat
- Will Not Start
- See more...
Installation Instructions
Robert from Mt. Vernon, IN
The Bake-o-lite (Hard Plastic) block that holds the burners female connection in place had chipped away over time and wouldn't allow the male part of the burner to connect up correctly.
After unplugging the range I took the rear sheet metal panel at the top off with a nut driver to expose the wiring connections. The next step was to remove the single screw holding the old part in place. (under the drip pan) Once free I snipped the old part from the wires and then taped the new female ends to the old wires with black electrical tape. From rear I carfully pulled the old wires through the back until I could reach the new wiring connections. Unplugged old, plugged in new and replaced the rear metal cover. Then I put the screw that holds the new block bracket in place, replaced drip pan, and burner. The final step was to plug the range back in and check to see if the burner worked. It did and I was done. Approx. 5 minutes
Read more...
Your Price
$78.35
In Stock
Kenmore Cooktop Surface Burner Terminal Block Kit
PartSelect Number PS232606
Manufacturer Part Number WB17X210
This is a surface burner terminal block kit, also known as range surface element receptacle, for an oven, range, or stove. The kit comes with the terminal block, mounting clip, and wires. This surface burner terminal block kit connects the wiring harness to the surface elements. It is important to shut off the power to the appliance before starting this repair. You will need to remove all four elements, trim rings, and drip bowls to access the terminal block on your stovetop. This is an OEM replacement part that is sourced from the genuine manufacturer.
Fixes these symptoms
- Element will not heat
- See more...
Installation Instructions
Shaohui from East Lansing, MI
There was no heat on the coils.
I opened the lid, and found that the terminal blocks were burnt, the wires were melted. I ordered one set of terminal block to replace the burnt one, and it worked. Before I started, I shut off the electricity in the whole house to be safe.
Read more...
Your Price
$38.38
In Stock
Kenmore Cooktop Terminal Block
PartSelect Number PS232646
Manufacturer Part Number WB17X5113
This kit includes one ceramic block with 6" wire leads, 2 wire nuts and 2 heat shrink with mounting bracket.
Fixes these symptoms
- Element will not heat
- See more...
Installation Instructions
Richard from Apex, NC
Heating element required continuous adjustments to work.
I removed old 8" surface element and terminal block. Some of old wiring had to be cut off because of harding/cracking of old wiring. Stove was 23 years old and this burner was the most frequently used one. I soldered the new and remaining old wires together. I used the shirnk wrap that came with the terminal block to cover the solder joint. I screwed the new terminal block (one screw holds it in place - used same screw from old terminal block that was removed). I finished by inserting the new surface element. Everything works fine. In the next week or two after we use it a while, I will check wiring again to make sure there are no changes. You need to be very careful as it gets very hot under the burner.
Read more...
Your Price
$8.06
In Stock
Your Price
$24.59
In Stock
Kenmore Cooktop Main Power Terminal Block
PartSelect Number PS11745232
Manufacturer Part Number WP8203546
Sold individually.
Fixes these symptoms
- Will Not Start
- See more...
Installation Instructions
Frank from Silverhill, AL
Your Price
$47.69
In Stock
Kenmore Cooktop Cartridge Receptacle
PartSelect Number PS11757565
Manufacturer Part Number WPY702434
This cartridge receptacle is almost four inches long. It is white in color and is made of ceramic.
Fixes these symptoms
- Element will not heat
- See more...
Installation Instructions
Stephen from Andover, MA
Infinite switch ran more than one burner
Purchased 1 infinite switch and installed it on the left front burner. problem still there so I used the switch that I replaced on the rear burner and all was ok. The front switch had been sending full heat to the rear burner,but the problem ended up with the rear switch. The switches are interconnected and all are the same part number.Diagrams on partsselect were the key to a successful repair.To access the switch you need only to remove the fan cover, remove the 2 screws holding the switch assembly and move it foreward and then lift to reveal slide on connectors. Power to the unit is off at the main panel during the entire process.
Read more...
Related Kenmore Cooktop Parts
- All Kenmore Cooktop parts
- Kenmore Cooktop Brackets and Flanges
- Kenmore Cooktop Caps and Lids
- Kenmore Cooktop Deflectors and Chutes
- Kenmore Cooktop Drip Bowls
- Kenmore Cooktop Elements and Burners
- Kenmore Cooktop Grates
- Kenmore Cooktop Hardware
- Kenmore Cooktop Hoses and Tubes
- Kenmore Cooktop Insulations
- Kenmore Cooktop Knobs
- Kenmore Cooktop Lights and Bulbs
- Kenmore Cooktop Panels
- Kenmore Cooktop Seals and Gaskets
- Kenmore Cooktop Springs and Shock Absorbers
- Kenmore Cooktop Switches
- Kenmore Cooktop Valves
