Kenmore Cooktop Seals and Gaskets

Kenmore Appliance Parts

Popular Kenmore Cooktop Seals and Gaskets

Your Price
$12.03
  In Stock
Kenmore Cooktop SEAL CNTL (Black)
★★★★★
★★★★★
1 Review
PartSelect Number PS952314
Manufacturer Part Number WB04T10042
Your Price
$28.25
  In Stock
Kenmore Cooktop Burner Bowl Seal
★★★★★
★★★★★
3 Reviews
PartSelect Number PS244608
Manufacturer Part Number WB32M8
This part is the replacement burner bowl seal or drip pan seal for your range. It is black in color and is sold individually. The burner bowl seal creates a seal between the cooktop and the drip pan and prevents spills from leaking between them. If the seal is broken or worn, it can allow spills to leak under the cooktop. To replace the seal, carefully remove it from under the drip pan, and fit the new seal into place. This is an OEM part sourced directly from the manufacturer.
Installation Instructions
Bill from Corona, CA
worn / chipped bowl
Removed two screws, pulled out the igniter wire, removed a spring type wire holding the igniter to the bowl. Replace with new bowl, reconnected wire and placed new washer around bowl, placed back on stove top and screwed in place. Less than ten minutes to replace and only used a phillips screw driver. Read more...
Your Price
$24.26
  In Stock
Kenmore Cooktop Burner Pan Gasket
PartSelect Number PS442167
Manufacturer Part Number 318053901
Your Price
$14.15
  In Stock
Kenmore Cooktop SEAL CNTL (WHT)
PartSelect Number PS952312
Manufacturer Part Number WB04T10040
Your Price
$12.90
  In Stock
Kenmore Cooktop Burner Gasket
PartSelect Number PS227129
Manufacturer Part Number WB04T10012
Installation Instructions
Michael from Weatogue, CT
No spark at one burner
Other writers have claimed that this is a "really easy" job. They apparently had one or more of: 1. Less used appliance. 2. Never spilled anything on the cooktop 3. Much better luck. In my case, the apparently faulty igniter absolutely would not pull out. I removed it by removing the burner retaining screws and prying under the burner casting. Having done that, I cleaned the igniter and tested it again. None of the igniters worked, and I could hear arcing under the cooktop, indicating one or more of the igniter HV wires had somehow grounded. After a fruitless search for instructions on raising the cooktop, I stumbled upon an envelope glued to the back of the range that told me to remove all four burners and igniters and to release the cooktop by inserting a thin screwdriver under the front edge about 3" from each end to release the spring clips. Several of the igniters were cemented in place with caramelized sugar and required some pretty vigorous prying to dislodge. If I had this to do again on a range that had been ridden hard, I wouldproactively order a full set of gaskets (they're fragile), the HV harness (even if it doesn't leak as mine did, the igniter connectors degrade from heat exposure), a set of electrode mounting clips (none of them were much use either), and enough igniters to replace any that don't work plus at least one. I pried out the recalcitrant igniters; in retrospect I should have crushed them because of the severe risk imposed by prying of breaking either a burner casting or the cooktop -- either of which are far more expensive than another igniter. Read more...
Your Price
$48.38
  In Stock
Kenmore Cooktop SEAL
PartSelect Number PS440056
Manufacturer Part Number 316242001
Your Price
$42.12
  In Stock
Kenmore Cooktop SEAL
PartSelect Number PS440057
Manufacturer Part Number 316242002
Your Price
$32.19
  In Stock
Kenmore Cooktop Switch Seal
PartSelect Number PS243590
Manufacturer Part Number WB2X9504
This part goes between the infinite switch (under the cooktop) and the knob.
Installation Instructions
Fitzroy from PLANTATION, FL
The large burner would not light up when turned on
I followed the instructions on you tube Read more...
Your Price
$32.24
  In Stock
Kenmore Cooktop Surface Burner Seal
PartSelect Number PS820345
Manufacturer Part Number 316242004
Your Price
$58.35
  In Stock
Kenmore Cooktop Burner Seal
PartSelect Number PS440055
Manufacturer Part Number 316242000
Sold individually.
Installation Instructions
GONZALO from DORAL, FL
The repair part did not include the screws and the old ones were rusted and broke
The burner skirt should include the screws to attach it. The lack of screws complicates the installation as new holes need to be made Read more...

Related Kenmore Cooktop Parts