Dishwasher Dispensers
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Dishwasher Dispensers
Your Price
$158.01
In Stock
Dishwasher Detergent Dispenser
Remove all screws around the stainless metal shroud inside the door. DONT remove the hinge screws.
Torx bit required.
Unplug detergent dispenser and place outer door assembly aside. Dispenser has small clips holding it in, top, bottom and sides I believe. Push these in, dispenser falls out into dishwasher.
Insert new unit, reverse all steps. Done.
Dont for get to reattach the wires! Read more...
PartSelect Number PS11731570
Manufacturer Part Number W10861000
Detergent dispenser W10861000 is an original equipment manufacturer (OEM) part that fits some Whirlpool, KitchenAid, Maytag and Amana dishwashers.
Detergent dispenser W10861000 attaches to the inner door panel and holds the dishwasher detergent and rinse aid in covered compartments.
This dishwasher detergent dispenser measures approximately 5 inches wide and 4.5 inches high.
Fixes these symptoms
- Door latch failure
- Not cleaning dishes properly
- Will not dispense detergent
- See more...
Installation Instructions
David from Swanzey, NH
Detergent door was not locking closed
Super simple.Remove all screws around the stainless metal shroud inside the door. DONT remove the hinge screws.
Torx bit required.
Unplug detergent dispenser and place outer door assembly aside. Dispenser has small clips holding it in, top, bottom and sides I believe. Push these in, dispenser falls out into dishwasher.
Insert new unit, reverse all steps. Done.
Dont for get to reattach the wires! Read more...
Your Price
$82.12
In Stock
Dishwasher Detergent Dispenser
PartSelect Number PS11770487
Manufacturer Part Number 5304506521
This is the replacement detergent dispenser for your refrigerator. It is gray in color and is sold individually. It is approximately 8.5 inches long and 3 inches wide. The detergent dispenser stores the detergent until it is ready to be dispensed. If your dishes are not coming clean, or you notice the detergent is still in the dispenser at the end of the cycle, you may have a damaged or malfunctioning detergent dispenser. This is an OEM part sourced directly from the manufacturer.
Fixes these symptoms
- Door latch failure
- Leaking
- Not cleaning dishes properly
- See more...
Installation Instructions
Bernard from ACUSHNET, MA
The soap dispenser didn’t dispense the soap
After shutting off power to the dishwasher, I removed the two screws holding the door cover on the inside of the door sides, about 8 inches from the bottom of the door. I slid the cover down and off, and unplugged the wires to the dispenser. Then I removed the six screws holding the dispenser in place, removed the old dispenser, installed the new one, replaced the six screws and plugged the wires back in. The door cover and the two screws was all that was left. It took about ten minutes. Easy.
Read more...
Your Price
$177.85
In Stock
Dishwasher Detergent Dispenser Assembly
PartSelect Number PS11750167
Manufacturer Part Number WPW10199696
This part releases the detergent and rinse aid into the dishwasher. Light grey in color. The detergent dispenser attaches to the inner door panel and holds the dishwasher detergent and rinse agent in a covered compartment.
Fixes these symptoms
- Door latch failure
- Door won’t close
- Leaking
- See more...
Installation Instructions
Craig from Austin, TX
latch on dispenser cover broke
Printed door assembly parts list and photo from KitchenAid website. (With the absence of instructions, it was a big help.) Remove door cover. You'll need a star driver bit. Remove the old dispenser. Note how the metal clamp and black cover sheet are positioned. Install the new dispenser. Insure the wiring harness is snapped in place. Replace the door cover. Not difficult; just some patience. One more hint ... be careful when taking the door cover off and you won't have to disconnect any other wiring.
Read more...
Your Price
$93.12
In Stock
Dishwasher Dispenser
PartSelect Number PS11757054
Manufacturer Part Number WPW10671905
Fixes these symptoms
- Door latch failure
- Not cleaning dishes properly
- Will not dispense detergent
- See more...
Installation Instructions
Gloria from OCEAN CITY, NJ
Soap Dispenser door is broken
Open door and remove 12 T15 torx screws. Note that the 4 along the top edge are longer than the 8 along the sides. Lift the door panel upwards to remove the panel. Remove 6 screws securing the soap dispenser and metal bracket. Unplug the cable on the right side by pressing down on the locking tab. Note the position of the black plastic sheet that covers the back of the dispenser, and the white insulator on the right side. open the door part way and press down on the release for the dispenser on the outside of the door. The dispenser can now be removed from the inside of the door. Install the new dispenser and snap in place. Put the metal bracket back in place with the insulators and secure with the 6 screws. Re-install the shorter screws first, then the longer ones across the top.
Read more...
Your Price
$59.67
In Stock
Dishwasher Detergent Dispenser
Unscrewed 4 phillips screws from top of outer door.
Unscrewed 2 screws each siide of door.
Lower outer door section drops away.
Note wiring sequence on dispenser, then disconnect wires.
Unscrew 6 screws on dispenser and lift dispenser out.
Place new dispenser in place (note orientation), ann fasten in place with screws, remembering to replace wire retainer on left lower screw.
Reconnect wires to dispenser correctly.
Slide lower outer door over tabs and secure with the 4 side screws.
Ensure lower door is up under control panel and secure with the 4 top screws.
Fill dispenser with detergent, reconnect power and test run while enjoying a cup of tea in celebration of a job well done.. Read more...
PartSelect Number PS11770680
Manufacturer Part Number 5304507354
This part releases the detergent and rinse aid into the dishwasher. NOTE: Color may vary but the part will function the same as the original.
Fixes these symptoms
- Door latch failure
- Door won’t close
- Leaking
- See more...
Installation Instructions
C from Covina, CA
Dispenser door broken.
Disconnect from powerUnscrewed 4 phillips screws from top of outer door.
Unscrewed 2 screws each siide of door.
Lower outer door section drops away.
Note wiring sequence on dispenser, then disconnect wires.
Unscrew 6 screws on dispenser and lift dispenser out.
Place new dispenser in place (note orientation), ann fasten in place with screws, remembering to replace wire retainer on left lower screw.
Reconnect wires to dispenser correctly.
Slide lower outer door over tabs and secure with the 4 side screws.
Ensure lower door is up under control panel and secure with the 4 top screws.
Fill dispenser with detergent, reconnect power and test run while enjoying a cup of tea in celebration of a job well done.. Read more...
Your Price
$76.65
In Stock
Dishwasher Detergent and Rinse Aid Dispenser
PartSelect Number PS11750654
Manufacturer Part Number WPW10224428
This part releases the detergent and rinse aid into the dishwasher. This detergent dispenser is for dishwashers.
Detergent dispenser holds the dishwasher detergent in a covered compartment.
Unplug the dishwasher or shut off the house circuit breaker before installing this part. Wear work gloves to protect your hands during this repair.
Fixes these symptoms
- Door latch failure
- Door won’t close
- Leaking
- See more...
Installation Instructions
Burt from Richardson, TX
dispenser didn't stay closed
Ordered new part and installed it. I found a repair manual online and the replacement was pretty easy. I removed 8 screws that held the outer door and the dispenser was sitting there looking at me. I disconnected the solenoid, pried apart two clips and the old dispenser came right out. Reversed the process to install the new one.
Read more...
Your Price
$84.00
In Stock
Dishwasher Detergent Dispenser with Rinse Cap
Removed the phillips head screws that held the door together. The screw are located on the inside edge of the door, there are 10-12 of them.
Spearated the door shells carefully, trying not to disturb the location of the wiring in the middle of the door.
Found the 4 screws that hold the module assembly to the door from the inside, and removed them.
Popped the assembly out, cleaned the gasket-seat area and placed the new one in place.
Carefully tightened the 4 screws. It is easy to over-tighten them, so only turn them until you feel they are snug. Let the gasket do the work.
Attached the two solenoid control wires in the same positions they were in before they were removed from the old assembly.
Re-assembled the door halves, again taking care to not over-tighten the phillips-head screws. One got "spun" and I removed it and re-set it into some epoxy.
Returned power to the dishwasher, and stopped washing dishes by hand.
Note: the latch is now made with a plastic that is more dense, and likely will not fail as soon as the original one did. I think GE learned something about the durability of their component plastics since this was originally built. Read more...
PartSelect Number PS958966
Manufacturer Part Number WD12X10163
This detergent dispenser assembly is attached to the inner door panel of a dishwasher. This part holds detergent and dishwasher rinse products in a covered container. If your dispenser will not open, close, dispense detergent properly, or the dishes are coming out of the dishwasher dirty, replacing this part can solve these problems. The tools needed for this installation project are a #2 Phillips screwdriver and needle-nose pliers. To repair, first remove screws from the bottom of the inner door panel. Next, remove connecters, wires, and screws from the dispenser to access it and replace with new dispenser. Refer to the manual provided by the manufacturer for further installation instructions and guidance. Unplug dishwasher from power source as a safety precaution.
Fixes these symptoms
- Door latch failure
- Door won’t close
- Leaking
- See more...
Installation Instructions
James from Naperville, IL
soap door latch broken, wouldn't hold soap for later release in middle of cycle like it was supposed to.
Turned off power to unit, 'cuz it has a solenoid lead to open the soap door. Removed the phillips head screws that held the door together. The screw are located on the inside edge of the door, there are 10-12 of them.
Spearated the door shells carefully, trying not to disturb the location of the wiring in the middle of the door.
Found the 4 screws that hold the module assembly to the door from the inside, and removed them.
Popped the assembly out, cleaned the gasket-seat area and placed the new one in place.
Carefully tightened the 4 screws. It is easy to over-tighten them, so only turn them until you feel they are snug. Let the gasket do the work.
Attached the two solenoid control wires in the same positions they were in before they were removed from the old assembly.
Re-assembled the door halves, again taking care to not over-tighten the phillips-head screws. One got "spun" and I removed it and re-set it into some epoxy.
Returned power to the dishwasher, and stopped washing dishes by hand.
Note: the latch is now made with a plastic that is more dense, and likely will not fail as soon as the original one did. I think GE learned something about the durability of their component plastics since this was originally built. Read more...
Your Price
$11.10
In Stock
Dishwasher Soap Cup Latch Kit
You have to take off the nine star pointed screws. So you need a special screwdriver or I had a socket set of them and I used a ratchet to make it easier. I think there are nine of them around the base of the door. Then remove the door and set it on the counter. Flip it over and there is a small plastic cover that has to be removed from the back of it, and it is easily removed by gently pulling on it.
Now comes the difficult part. There is a locking piece on it that holds the latch onto the door by interlocking with a piece on the back side of the door. I took a pair of wire snips and just cut the old interlocking piece off. This way I didn't have to try and slide the two interlocking pieces apart.
When you go to put the new piece on before you interlock them make sure they are put on right. Specifically the latch is pointing the right way to seal the detergent door. Otherwise it can be a pain to separate the interlocking pieces again. (which is why I cut it off the old one).
Then you're done. Just put it all back together. Read more...
PartSelect Number PS382922
Manufacturer Part Number 676413
This soap cup latch kit, used in a dishwasher, will keep the dispenser cover closed. If your dishwasher will not dispense detergent, there is a door latch failure, the dishes are not cleaning properly, or there is leaking, then this kit can be the solution to your symptoms. The tools required for this replacement are a #15 torx bits, a small blade screwdriver, and slip joint pliers. First locate the soap box and remove the latch on both sides. Next step is to remove the screws in the inner door panel and remove the plastic cover at the back. Remove the old latch assembly and add the new one. Make sure to unplug your dishwasher before beginning this installation project.
Fixes these symptoms
- Door latch failure
- Door won’t close
- Leaking
- See more...
Installation Instructions
Steven from Edmond, OK
Latch broke on dishwasher
Look at the exploded parts diagram, that parts select provides on their website.You have to take off the nine star pointed screws. So you need a special screwdriver or I had a socket set of them and I used a ratchet to make it easier. I think there are nine of them around the base of the door. Then remove the door and set it on the counter. Flip it over and there is a small plastic cover that has to be removed from the back of it, and it is easily removed by gently pulling on it.
Now comes the difficult part. There is a locking piece on it that holds the latch onto the door by interlocking with a piece on the back side of the door. I took a pair of wire snips and just cut the old interlocking piece off. This way I didn't have to try and slide the two interlocking pieces apart.
When you go to put the new piece on before you interlock them make sure they are put on right. Specifically the latch is pointing the right way to seal the detergent door. Otherwise it can be a pain to separate the interlocking pieces again. (which is why I cut it off the old one).
Then you're done. Just put it all back together. Read more...
Your Price
$152.85
In Stock
Dishwasher Detergent and Rinse Dispenser with Cap
PartSelect Number PS11750655
Manufacturer Part Number WPW10224430
This part releases the detergent and rinse aid into the dishwasher.
Fixes these symptoms
- Door latch failure
- Door won’t close
- Leaking
- See more...
Installation Instructions
Jim from Sherwood, OR
The dispenser door was broken, would not close.
First I removed the (8) screws holding the front door panel on. Then I took the door panel off and unpluged the ribbon wiring so the door was free from the dishwasher. I then unpluded the wiring going to the dispensor. Then I removed the (6) screws holding the dispensor into place and then sprung the holders (2) so the dispendor could be removed. I stuck the new dispensor in its place, pushed it in so the (2) metal holders locked into place, then replaced the (6) screws, pluged the wiring into the new dospensor, pluged the ribbion wiring back in and replaced the front door panel and reinstalled the (8) screws that hold the front door into place. And then tested and everything worked fine.
Read more...
Your Price
$27.34
In Stock
Dishwasher Soap Dispenser Cover
PartSelect Number PS11741342
Manufacturer Part Number WP3378138
This part covers your soap dispenser and is spring loaded.
Fixes these symptoms
- Door latch failure
- Door won’t close
- Leaking
- See more...
Installation Instructions
KEVIN from PLAINFIELD, IL
soap dispenser door/spring broken
removed old parts and re-installed new parts. The spring is a little hard to get to the right point without a jewelers screwdriver, after that everything worked fine.
Read more...
Dishwasher Dispenser Brands
- Amana Dishwasher Dispensers
- Bosch Dishwasher Dispensers
- Crosley Dishwasher Dispensers
- Estate Dishwasher Dispensers
- Frigidaire Dishwasher Dispensers
- Gaggenau Dishwasher Dispensers
- General Electric Dishwasher Dispensers
- Inglis Dishwasher Dispensers
- Jenn-Air Dishwasher Dispensers
- Kenmore Dishwasher Dispensers
- KitchenAid Dishwasher Dispensers
- Magic Chef Dishwasher Dispensers
- Maytag Dishwasher Dispensers
- Roper Dishwasher Dispensers
- Whirlpool Dishwasher Dispensers
