Whirlpool Dishwasher Dispensers

Your Price

$152.63

Detergent Dispenser

★★★★★

16 Reviews

PartSelect Number PS11731570

Manufacturer Part Number W10861000

Detergent dispenser W10861000 is an original equipment manufacturer (OEM) part that fits some Whirlpool, KitchenAid, Maytag and Amana dishwashers. Detergent dispenser W10861000 attaches to the inner door panel and holds the dishwasher detergent and rinse aid in covered compartments. This dishwasher detergent dispenser measures approximately 5 inches wide and 4.5 inches high.

Fixes these symptoms

Door latch failure
Not cleaning dishes properly
Will not dispense detergent
See more...

Installation Instructions

David from Swanzey, NH

Detergent door was not locking closed

Super simple.
Remove all screws around the stainless metal shroud inside the door. DONT remove the hinge screws.
Torx bit required.

Unplug detergent dispenser and place outer door assembly aside. Dispenser has small clips holding it in, top, bottom and sides I believe. Push these in, dispenser falls out into dishwasher.

Insert new unit, reverse all steps. Done.
Dont for get to reattach the wires! Read more...

Your Price

$161.33

Detergent Dispenser Assembly

★★★★★

27 Reviews

PartSelect Number PS11750167

Manufacturer Part Number WPW10199696

This part releases the detergent and rinse aid into the dishwasher. Light grey in color. The detergent dispenser attaches to the inner door panel and holds the dishwasher detergent and rinse agent in a covered compartment.

Fixes these symptoms

Door latch failure
Door won’t close
Leaking
See more...

Installation Instructions

Craig from Austin, TX

latch on dispenser cover broke

Printed door assembly parts list and photo from KitchenAid website. (With the absence of instructions, it was a big help.) Remove door cover. You'll need a star driver bit. Remove the old dispenser. Note how the metal clamp and black cover sheet are positioned. Install the new dispenser. Insure the wiring harness is snapped in place. Replace the door cover. Not difficult; just some patience. One more hint ... be careful when taking the door cover off and you won't have to disconnect any other wiring. Read more...

Your Price

$70.38

Detergent and Rinse Aid Dispenser

★★★★★

29 Reviews

PartSelect Number PS11746408

Manufacturer Part Number WP8558129

This part releases the detergent and rinse aid into the dishwasher.

Fixes these symptoms

Door latch failure
Door won’t close
Leaking
See more...

Installation Instructions

ROY from PHILPOT, KY

Dispenser worked intermittently

First, I brought in my electric screwdriver and torx bit set. The screws holding the door are torx type. I removed the screws holding the door cover allowing access to the (6) hex head screws holding the dispenser in place. Raising the plastic flap covering the dispenser I removed the (2) electrical plugs from the solenoid. Using my elec/screwdriver and a 3/16" socket I quickly removed the old dispenser.
I cleaned the gasket area with some 409 and a paper towel and slid the new dispenser into place. I used a 3/16" nutdriver to tighten the screws. I tightened the screws in a cross pattern in (3) stages so as not to squeeze the gasket out of position. Screw slowly and the screws will bottom out when the proper gasket tension has been achieved, don’t over tighten.
I closed the door and ran the dishwasher in rinse cycle checking for leaks. After a couple of minutes and no leaks I pushed the cancel and drain button. I folded the plastic cover back down over the dispenser and reinstalled the outer door cover tightening all screws with my electric screwdriver and torx bit. I opened the door and filled the rinse dispenser.
We've used the dishwasher several times since the repair and the dispenser has worked fine. Read more...

Your Price

$12.56

Pin (Lid Hinge)

★★★★★

1 Review

PartSelect Number PS11741308

Manufacturer Part Number WP3372028

The lid hinge pin or detergent lid pin on your dishwasher helps dispense your dish detergent when your dishwasher is running. The pin fits with the dispenser lid and allows the lid to pop open and dispense detergent. It is a small, plastic pin that is approximately 3 inches in length. Due to its small size, the pin can be damaged relatively easily, and if your pin is broken or missing, it will need to be replaced. This product is sold individually.

Fixes these symptoms

Door latch failure
Door won’t close
Not cleaning dishes properly
See more...

Installation Instructions

HAROLD from FISHERSVILLE, VA

Worn out spring on detergent release box lid

First, examine very carefully how the old spring relates to the detergent release box lid. Note that the top of the spring has a square-end upside down "U" . This rests on a small ledge on the detergent box. Also note that on either end of the spring is a straight extension of the spring wire. These two "legs" must rest on the inside of the edge of the detergent box. Second, use a flat blade screw driver to pry the LID hinge pin from the mounting "posts. Remove the pin, first noting the position of the spring. Reassemble the spring on the hinge pin in reverse order. Then snap the lid onto the spring using the two mounting "posts". NOTE: I used a very fine needle nose pliers to move the two spring "legs" behind the detergent box edge after I had mounted the lid. Flip the lid down to test if the spring pressure on the lid can be felt. Harold Kitzmann, Fishersville VA Read more...

Your Price

$84.45

Dispenser

★★★★★

5 Reviews

PartSelect Number PS11757054

Manufacturer Part Number WPW10671905

Fixes these symptoms

Door latch failure
Will not dispense detergent
See more...

Installation Instructions

Gloria from OCEAN CITY, NJ

Soap Dispenser door is broken

Open door and remove 12 T15 torx screws. Note that the 4 along the top edge are longer than the 8 along the sides. Lift the door panel upwards to remove the panel. Remove 6 screws securing the soap dispenser and metal bracket. Unplug the cable on the right side by pressing down on the locking tab. Note the position of the black plastic sheet that covers the back of the dispenser, and the white insulator on the right side. open the door part way and press down on the release for the dispenser on the outside of the door. The dispenser can now be removed from the inside of the door. Install the new dispenser and snap in place. Put the metal bracket back in place with the insulators and secure with the 6 screws. Re-install the shorter screws first, then the longer ones across the top. Read more...

Your Price

$74.04

Detergent and Rinse Aid Dispenser

★★★★★

21 Reviews

PartSelect Number PS11750654

Manufacturer Part Number WPW10224428

This part releases the detergent and rinse aid into the dishwasher. This detergent dispenser is for dishwashers. Detergent dispenser holds the dishwasher detergent in a covered compartment. Unplug the dishwasher or shut off the house circuit breaker before installing this part. Wear work gloves to protect your hands during this repair.

Fixes these symptoms

Door latch failure
Door won’t close
Leaking
See more...

Installation Instructions

Burt from Richardson, TX

dispenser didn't stay closed

Ordered new part and installed it. I found a repair manual online and the replacement was pretty easy. I removed 8 screws that held the outer door and the dispenser was sitting there looking at me. I disconnected the solenoid, pried apart two clips and the old dispenser came right out. Reversed the process to install the new one. Read more...

Your Price

$26.41

Soap Dispenser Cover

★★★★★

1 Review

PartSelect Number PS11741342

Manufacturer Part Number WP3378138

This part covers your soap dispenser and is spring loaded.

Fixes these symptoms

Door latch failure
Door won’t close
Leaking
See more...

Installation Instructions

KEVIN from PLAINFIELD, IL

soap dispenser door/spring broken

removed old parts and re-installed new parts. The spring is a little hard to get to the right point without a jewelers screwdriver, after that everything worked fine. Read more...

Your Price

$104.32

Dispenser

★★★★★

13 Reviews

PartSelect Number PS11750038

Manufacturer Part Number WPW10195175

This detergent dispenser assembly is for dishwashers. Detergent dispenser assembly holds the dishwasher detergent and rinses agent in covered compartments.

Fixes these symptoms

Door latch failure
Door won’t close
Leaking
See more...

Installation Instructions

Chris from MANSFIELD, TX

Dispenser was not dispensing

I first turned the power off to the dishwasher. I then used the star bit to loosen the screws on the sides and top. Note that the 4 top screws are longer than the side screws. Once the screws were loose I used a clamp on each side to hold the door cover in place. Once the screws were removed, I released the clamps, raised the door then lifted the outer cover off. I then peeled the insulation back from the top to expose the dispenser. I used a small socket to remove the screws for the dispenser. I released the plug with a small slotted screw driver. I then exchanged the dispenser with the new unit being careful to correctly reinstall the black cover over the top. I reinstalled the door cover, being careful to tuck the insulation back in place. I then installed the screws using the clamps to hold the door in place during the reinstall. Read more...

Your Price

$10.72

Soap Cup Latch Kit

★★★★★

9 Reviews

PartSelect Number PS382922

Manufacturer Part Number 676413

This soap cup latch kit, used in a dishwasher, will keep the dispenser cover closed. If your dishwasher will not dispense detergent, there is a door latch failure, the dishes are not cleaning properly, or there is leaking, then this kit can be the solution to your symptoms. The tools required for this replacement are a #15 torx bits, a small blade screwdriver, and slip joint pliers. First locate the soap box and remove the latch on both sides. Next step is to remove the screws in the inner door panel and remove the plastic cover at the back. Remove the old latch assembly and add the new one. Make sure to unplug your dishwasher before beginning this installation project.

Fixes these symptoms

Door latch failure
Door won’t close
Leaking
See more...

Installation Instructions

Steven from Edmond, OK

Latch broke on dishwasher

Look at the exploded parts diagram, that parts select provides on their website.

You have to take off the nine star pointed screws. So you need a special screwdriver or I had a socket set of them and I used a ratchet to make it easier. I think there are nine of them around the base of the door. Then remove the door and set it on the counter. Flip it over and there is a small plastic cover that has to be removed from the back of it, and it is easily removed by gently pulling on it.

Now comes the difficult part. There is a locking piece on it that holds the latch onto the door by interlocking with a piece on the back side of the door. I took a pair of wire snips and just cut the old interlocking piece off. This way I didn't have to try and slide the two interlocking pieces apart.

When you go to put the new piece on before you interlock them make sure they are put on right. Specifically the latch is pointing the right way to seal the detergent door. Otherwise it can be a pain to separate the interlocking pieces again. (which is why I cut it off the old one).

Then you're done. Just put it all back together. Read more...