Amana Dishwasher Pumps
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Amana Dishwasher Pumps
Your Price
$78.26
In Stock
Amana Dishwasher Circulation Pump
PartSelect Number PS16744934
Manufacturer Part Number W11612326
This circulation pump is a genuine OEM replacement part designed for use in dishwashers. It is responsible for circulating water throughout the dishwasher during the wash and rinse cycles. The circulation pump draws water from the dishwasher tub, pressurizes it, and then distributes it to the spray arms, which spray the water onto the dishes to remove food particles and debris. The circulation pump may fail due to several reasons such as an electrical fault, a blockage in the pump impeller, motor failure, or physical damage. A faulty pump will result in water leakages, unusually loud noises during use, reduced water circulation, and poor cleaning performance.
Fixes these symptoms
- Leaking
- Not cleaning dishes properly
- Not draining
- See more...
Installation Instructions
Samoil from COOPER CITY, FL
The dish washer wasn’t cleaning dishes
The circulation pump is a super easy fix and the installation video parts select has on its website is accurate. I felt the most difficult part of the repair was removing the dishwasher from the kitchen counter to make the repairs. After you get the dishwasher out, you pretty much just pop the old pump out with your hands and a flat head screwdriver. (The supplied video is spot on ) Installing the new pump will require a pinch plier or a hose clamp. I chose a new hose clamp as it is cheaper and I would never use the pinch pliers after this job.
Read more...
Your Price
$62.60
In Stock
Amana Dishwasher Drain Pump
First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done. Read more...
PartSelect Number PS11753379
Manufacturer Part Number WPW10348269
This drain pump is used in dishwashers to remove water from the dishwasher tub. If the impeller in the dishwasher is damaged or the motor has been shorted out and will not drain, it is possible the body is cracked, causing leakage. To prevent this from happening, replace the drain pump. The tools needed for this installation are: Phillips screwdriver, 5/16 inch nut driver, 5/8 inch wrench, and a flathead screwdriver. Remember to unplug your dishwasher from the power source before beginning this installation project. Refer to the manual provided by the manufacturer for further installation instructions.
Fixes these symptoms
- Leaking
- Noisy
- Not cleaning dishes properly
- See more...
Installation Instructions
Andrew from Alexandria, VA
dishwasher not draining after wash cycle
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release the old pump.First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done. Read more...
Your Price
$74.08
In Stock
Amana Dishwasher Circulation Pump
PartSelect Number PS16744935
Manufacturer Part Number W11612327
The pump motor delivers water to the spray arms to clean the dishes during the wash cycle.
Fixes these symptoms
- Not cleaning dishes properly
- Not draining
- Will not fill with water
- See more...
Your Price
$65.73
In Stock
Amana Dishwasher Drain Pump
Used pliers to loosen the pressure clamp on drain pump , have towel handy as there will be some water. Turn pump to left as you push in on the clip on side of drain pump. It will come out. Remove wire plug from old pump and plug into new pump than insert new pump and turn and push in till it clicks. Use pliers to pinch hose clamp and push hose onto pump release hose clamp. Turn breaker on. Run a cycle and make sure all is tight before putting skirt on front. Read more...
PartSelect Number PS11738151
Manufacturer Part Number W10876537
If your dishwasher isn’t draining properly or leaving water behind, this drain pump motor assembly might be the fix you need. It helps clear water from the tub during the drain cycle, keeping your appliance running smoothly and your dishes clean. This genuine replacement part is made to fit a variety of models from Whirlpool and related brands like Kenmore, KitchenAid, and Amana, making installation straightforward and dependable.
Fixes these symptoms
- Leaking
- Not draining
- See more...
Installation Instructions
Kelli from BURLINGTON, MA
Dish washer would not drain properly
Shut off breaker. Took off front skirt of dishwasher . Used pliers to loosen the pressure clamp on drain pump , have towel handy as there will be some water. Turn pump to left as you push in on the clip on side of drain pump. It will come out. Remove wire plug from old pump and plug into new pump than insert new pump and turn and push in till it clicks. Use pliers to pinch hose clamp and push hose onto pump release hose clamp. Turn breaker on. Run a cycle and make sure all is tight before putting skirt on front. Read more...
Your Price
$34.74
In Stock
Amana Dishwasher Chopper Assembly
2) Remove lower spray arm by unscrewing plastic screw, it should only be hand tight.
3) In order to remove the strainer cover, you will need to remove the plastic tube that takes water to the middle and top spray arms. Unclip this tube from the top and middle clips and then work it out of the strainer assembly tube. Now you should be able to remove the tube at the bottom of the dishwasher by unscrewing it 1/4 turn.
4) Remove the strainer cover by unscrewing the 4 Torqs screws.
5) You will now see two smaller torqs screws that hold the hold the Chopper Assembly cover down. Take these two screws out and remove the two piece cover.
6) Pull out the broken Chopper Assembly, make sure you get all the pieces!
7) Install the new Chopper Assembly. Make sure that you install the Assembly with the small part of the screen towards the bottom of the housing. Also make sure you compress the spring as you install the part. I used a small pair of neddle nose pliers to compress the spring behind the screen in order to install the chopper assembly.
8) Put everything back together and make sure it works! Read more...
PartSelect Number PS1734917
Manufacturer Part Number W10083957
This is a chopper assembly or drain food chopper, and it is designed for your dishwasher. The chopper chops up/minces the food particles in your dishwasher to prevent them from clogging the pump. You may need to replace this part if your dishes are not being cleaned properly, your appliance is particularly noisy, or you are noticing draining problems. The tools you will need to make this repair include a number 20 and a number 15 torque screwdriver, a small flat blade screwdriver, and a pair of needle nose pliers.
Fixes these symptoms
- Leaking
- Noisy
- Not cleaning dishes properly
- See more...
Installation Instructions
Bill from North Richland Hills, TX
Dishes on top rack of dishwasher were not being cleaned.
1) Remove top and bottom dish baskets from the dishwasher, this will give you room to work. To remove top basket there are clips at the end of the slide rails.2) Remove lower spray arm by unscrewing plastic screw, it should only be hand tight.
3) In order to remove the strainer cover, you will need to remove the plastic tube that takes water to the middle and top spray arms. Unclip this tube from the top and middle clips and then work it out of the strainer assembly tube. Now you should be able to remove the tube at the bottom of the dishwasher by unscrewing it 1/4 turn.
4) Remove the strainer cover by unscrewing the 4 Torqs screws.
5) You will now see two smaller torqs screws that hold the hold the Chopper Assembly cover down. Take these two screws out and remove the two piece cover.
6) Pull out the broken Chopper Assembly, make sure you get all the pieces!
7) Install the new Chopper Assembly. Make sure that you install the Assembly with the small part of the screen towards the bottom of the housing. Also make sure you compress the spring as you install the part. I used a small pair of neddle nose pliers to compress the spring behind the screen in order to install the chopper assembly.
8) Put everything back together and make sure it works! Read more...
Your Price
$157.45
In Stock
Amana Dishwasher Pump And Motor Assembly
PartSelect Number PS16875975
Manufacturer Part Number W11665769
This dishwasher pump and motor assembly is compatible with dishwashers. It is supplied directly by the original manufacturer to ensure that it fits perfectly with your model. The pump and motor are responsible for moving water throughout the dishwasher during the wash cycle. The pump draws water from the tub and pumps it through various channels, such as the detergent dispenser, spray arms, and drain hose. The motor provides the power necessary to drive the circulation pump, causing the pump to rotate and circulate water. If the assembly is faulty, you will notice difficulties starting or filling the dishwasher, poor cleaning performance, incomplete cycles, and water leaks.
Fixes these symptoms
- Leaking
- Not cleaning dishes properly
- See more...
Your Price
$115.48
In Stock
Amana Dishwasher Sump
PartSelect Number PS11755006
Manufacturer Part Number WPW10455268
This works in conjunction with the pump and filtration system. It is used to receive drainage for disposal.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Jason from MOLINE, IL
Water leaking through the sump shaft seal
First I removed everything off of the bottom of the dishwasher. Then I removed the main center piece that everything mounts to. Then I reinstalled the new center piece with the help of some evoo cooking spray (extra virgin olive oil) I sprayed it on the rubber seal to aid in getting that center piece installed without a battle. Then I reinstalled everything else in the reverse order that I removed it. The evoo cooking spray works wonders for more than just cooking !!!
Read more...
Your Price
$102.31
In Stock
Amana Dishwasher Impeller
PartSelect Number PS12069388
Manufacturer Part Number 8193951A
This is the replacement impeller kit for your dishwasher. This impeller kit comes with 4 pieces, including the impeller and seals which you will need for the repair. The impeller and seal kit is mounted on the dishwasher motor. If your dishwasher is not cleaning dishes properly, it may be an indication that your impeller has gone bad, and you are not getting proper water pressure. If the seals have gone bad, your dishwasher may start to leak. If you are having either of these problems, you may need to replace the impeller kit. Be sure to disconnect the water and power source from the dishwasher before you begin this repair. This is an OEM part sourced directly from the manufacturer.
Fixes these symptoms
- Leaking
- Noisy
- Not cleaning dishes properly
- See more...
Installation Instructions
Chauncey from Menan, ID
Started with a grinding noise in the bottom of the dishwasher, and then the thing just stopped cleaning the dishes. It wasn't pumping any water,
I removed the plasic inner parts, used the torx drivers to remove the internal platic plate that covered the sump. Found the food chopper cover and removed it. It had gotten a piece of plastiic wrapped around it. As it spun it had ground the teeth off the end of the drive on the impellor and the food chopper. I replace both as a set and it works fine.
Read more...
Your Price
$51.61
In Stock
Amana Dishwasher Wash Impeller
PartSelect Number PS11747701
Manufacturer Part Number WP99002659
This dishwasher wash impeller assembly is a key component that helps circulate water and detergent through the spray arms during each cycle. Made from durable, multi-finned plastic, it attaches to the motor shaft and spins to ensure thorough cleaning throughout the tub. If your dishwasher is leaving dishes dirty, making unusual noises, or leaking, a worn or damaged impeller may be the cause. Replacing it can restore proper water flow and improve overall performance.
Fixes these symptoms
- Leaking
- Noisy
- Not cleaning dishes properly
- See more...
Installation Instructions
Linda from Washington, WV
Dishwasher would not spray water. Water would drain but not spray
Removed the basketsThen removed the bottom spray arm with nut driver. Removed the cover and spray tower assembly. removed screw holding broken impeller. Replaced and reversed process. Really easy. As an aside. This dishwasher has been a major disappointment. lots of things not holding up. Didn't go cheap when buying it. Nice to find a site with good prices for parts
Read more...
Your Price
$54.24
In Stock
Amana Dishwasher Sump Pump Check Valve
PartSelect Number PS11745441
Manufacturer Part Number WP8268375
May differ in appearance, but functions same as original.
This valve allows the water to flow in the drain direction only and prevents the dirty water from coming back into the tub.
Fixes these symptoms
- Leaking
- Noisy
- Not cleaning dishes properly
- See more...
Installation Instructions
Patty from Caldwell, ID
Dishwasher leaving food residue on all dishes
Had to take apart dishwasher and replace chopper assembly. The dishwasher had a lot of debris in in including pieces of broken plastic forks. Now works great
Read more...
Related Amana Dishwasher Parts
- All Amana Dishwasher parts
- Amana Dishwasher Brackets and Flanges
- Amana Dishwasher Caps and Lids
- Amana Dishwasher Circuit Boards and Touch Pads
- Amana Dishwasher Dishracks
- Amana Dishwasher Dispensers
- Amana Dishwasher Doors
- Amana Dishwasher Fuses
- Amana Dishwasher Handles
- Amana Dishwasher Hardware
- Amana Dishwasher Hinges
- Amana Dishwasher Hoses and Tubes
- Amana Dishwasher Latches
- Amana Dishwasher Motors
- Amana Dishwasher Panels
- Amana Dishwasher Seals and Gaskets
- Amana Dishwasher Spray Arms
- Amana Dishwasher Springs and Shock Absorbers
- Amana Dishwasher Switches
- Amana Dishwasher Valves
- Amana Dishwasher Wheels and Rollers
- Amana Dishwasher Wire Plugs and Connectors