Amana Dishwasher Parts
Find your part
Enter your model number or a part number and click "Search"
Popular Amana Dishwasher Parts
Your Price
$9.92
Rack Track Stop
PartSelect Number PS11746591
Manufacturer Part Number WP8565925
The rack track stop on your dishwasher is designed to stop the dish rack at the appropriate place when opening and closing the rack. If your dishwasher is not cleaning your dishes properly, the rack stop may need to be replaced. The replacement part may differ slightly from the broken part, depending on the model. However, the different styles are interchangeable. This product is sold individually and comes in both a white and grey plastic version. Many of our customers found this repair to be very easy and takes less than 30 minutes to complete. Simply snap the old part out and snap the new part into place. You will not require any tools to complete the job. This is an authentic part approved by the manufacturer.
Fixes these symptoms
- Door latch failure
- Door won’t close
- Not cleaning dishes properly
- See more...
Installation Instructions
Steven from WASHINGTON, DC
Upper rack wheels had begun to break off. Shoddy design and materials.
I carefully followed the video instructions step by step. They were detailed, clear, and pointed out how to avoid installation mistakes. WIthout the video I would have been tempted to just figure it out myself - ("Hey, I'm a handy guy. How hard could it be, right?"). With the video I sailed right through with no dumb errors. The new rack adjuster wheel set is much sturdier than the Whirlpool original. It made sense to get new rack stops at the same time. Thank you, PartSelect.
Read more...
Your Price
$63.90
Dishwasher Heating Element
Step 2: Remove the screws holding the bottom kickplate.
Step 3: Loosen leveling legs.
Step 4: Pull dishwasher out of hole.
Step 5: Unlplug dishwasher.
Step 6: Disconnect wires from bottom of element in back.
Step 7: Remove plastic nuts holding element in place.
Step 8: Remove element.
Step 9: Reverse Steps 1-7.
Step 10: Drink beer. Read more...
PartSelect Number PS8260087
Manufacturer Part Number W10518394
This manufacturer-certified heating element is used to create heat during the dry cycle and increase water temperature during portions of the wash cycle when certain options are selected. If your dishes are not drying or the water in the dishwasher is not getting hot you may need to replace the element. This kit includes the heater, two heater fasteners, and is a genuine OEM part. Please remember to disconnect the power before starting the repair. Use a multi-meter to test your heating element for continuity to determine whether this is the part that is causing your symptom. This part does not include any washers. To make your repair, disconnect the wires from the bottom of the element in the back, remove the plastic nuts holding it in place, remove the element, and repeat these steps in reverse order to install your new part. This is an easy repair that requires only a screwdriver, wrench set, and should take less than 30 minutes.
Fixes these symptoms
- Leaking
- Not cleaning dishes properly
- Not draining
- See more...
Installation Instructions
Dennis from Sedro Woolley, WA
Heater element broken.
Step 1: Remove the screws in the bottom of the countertop.Step 2: Remove the screws holding the bottom kickplate.
Step 3: Loosen leveling legs.
Step 4: Pull dishwasher out of hole.
Step 5: Unlplug dishwasher.
Step 6: Disconnect wires from bottom of element in back.
Step 7: Remove plastic nuts holding element in place.
Step 8: Remove element.
Step 9: Reverse Steps 1-7.
Step 10: Drink beer. Read more...
Your Price
$16.28
Mounting Bracket
PartSelect Number PS11745496
Manufacturer Part Number WP8269145
The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking, or tilting forward. The bracket is made entirely of metal. It is recommended to check all brackets, if applicable, because they often wear at the same rate and both may need to be replaced. This is an OEM part that is sourced from the authentic manufacturer. Tools needed are a pair of needle nose pliers and a screwdriver.
Fixes these symptoms
- Door latch failure
- Door won’t close
- Leaking
- See more...
Installation Instructions
Judith from Essex, MA
Lost dishwasher brackets
I called an experienced plumber, who balanced and installed my new dishwasher properly, using the brackets I ordered from Parts Select, after an INEXPERIENCED plumber had tossed the factory-provided mounting brackets out with the shipping carton. Relief!
Read more...
Your Price
$44.48
Dishwasher Lower Dishrack Wheel Assembly - Gray
PartSelect Number PS11722152
Manufacturer Part Number W10195416V
This OEM gray Dishwasher Lower Dishrack Wheel Assembly is a plastic kit that allows the rack to slide in and out of the dishwasher easily. If it breaks or becomes damaged. sliding will feel difficult. This can happen due to normal wear and tear, and the part should be replaced if this occurs. Check your model number and user manual to make sure this part is correct. It attaches directly to the dishrack. To repair, open the dishwasher door and pull out the lower dishrack. Next, push the tab from both sides and it should pop out. To install the new wheel assembly, place it on the rack and make sure the caps overlap the wire from the inside before you clip it in place by pushing the wheel. It measures roughly 3x6 inches.
Fixes these symptoms
- Door latch failure
- Door won’t close
- Leaking
- See more...
Installation Instructions
Thomas from WEST OLIVE, MI
Broken wheel unit on the bottom dish rack
All you do is pop out the old wheel unit at two (2) points on the plastic wheel housing and pop in the new one. Easy fix. Less than a 5 minute fix.
Read more...
Your Price
$10.12
Friction Sleeve
PartSelect Number PS11745488
Manufacturer Part Number WP8268961
This part helps to keep your door quiet when it opens and closes.
Fixes these symptoms
- Door latch failure
- Door won’t close
- Noisy
- See more...
Installation Instructions
Arthur from YORKTOWN HTS, NY
Door will fall down after opening
unscrewed dishwasher from cabinet ...,moved out slightly....while door closed ...reached with long nosed pliers door spring pulled forward...and allowing white plastic part that fits through sleeve and fit new sleeve over it...pulled spring attaching white plastic part and pushed unit back to cabinet and replaced screws DONE.
Read more...
Your Price
$61.84
Dishwasher INLET VALVE
PartSelect Number PS12578165
Manufacturer Part Number W11175771
This water inlet valve should be located behind the lower kick plate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
Fixes these symptoms
- Leaking
- Not cleaning dishes properly
- Will not fill with water
- See more...
Installation Instructions
Melissa from AIKEN, SC
Inlet valve wasn't working
Put thread tape on threads. Screwed water hose to part. Pushed hose onto part. Pushed electric clip to part. Screwed part onto washer. Done
Read more...
Your Price
$88.83
Dishwasher Drain Pump
First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done. Read more...
PartSelect Number PS11753379
Manufacturer Part Number WPW10348269
This drain pump is used in dishwashers to remove water from the dishwasher tub. If the impeller in the dishwasher is damaged or the motor has been shorted out and will not drain, it is possible the body is cracked, causing leakage. To prevent this from happening, replace the drain pump. The tools needed for this installation are: Phillips screwdriver, 5/16 inch nut driver, 5/8 inch wrench, and a flathead screwdriver. Remember to unplug your dishwasher from the power source before beginning this installation project. Refer to the manual provided by the manufacturer for further installation instructions.
Fixes these symptoms
- Leaking
- Noisy
- Not cleaning dishes properly
- See more...
Installation Instructions
Andrew from Alexandria, VA
dishwasher not draining after wash cycle
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release the old pump.First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done. Read more...
Your Price
$10.72
Front Track Stop
PartSelect Number PS11755805
Manufacturer Part Number WPW10508950
This stopper is attached to the front of the top dishrack track. This stop keeps the upper rack from pulling out too far and falling from the track.
Fixes these symptoms
- Door latch failure
- Door won’t close
- Not cleaning dishes properly
- See more...
Installation Instructions
Sheila from FAYETTEVILLE, NY
Lost stop from one side of top rack. Rack could be pulled off track.
Looked at other side of top rack which still had the stop. Just had to orient the direction of the stop and push it firmly onto the rack arm. Took a couple tries, but it went in and locked. Works perfectly. Inexpensive and easy fix to to very annoying problem.
Read more...
Your Price
$27.88
GASKET
PartSelect Number PS16221222
Manufacturer Part Number W11498831
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Amy from MIDDLEBURG, FL
Leaking dishwasher
Removed old gasket. Cleaned the area and let dry. Aligned gasket, pressed into the groove. Corners are tricky, stretch and press to get a tight seal. Follow around appliance. Inital try, small leak. Adjusted seal second use no leak. 10/10 would recommend this part. Super easy self install.
Read more...
Your Price
$52.60
Dishwasher Filter
PartSelect Number PS11759673
Manufacturer Part Number W10872845
This filter works with the water pump in your dishwasher. It prevents debris from entering the pump and causing damage. As a result, the filter can occasionally become clogged or damaged, and will need to be replaced. A good indication of a damaged filter is if your dishwasher is not draining or cleaning the dishes properly. This filter has a gray plastic top and bottom that are approximately 5 inches in diameter. This is a genuine OEM part that comes directly from the manufacturer. To replace the filter, simply turn it counterclockwise to unlock, and then screw in the new filter
Fixes these symptoms
- Leaking
- Not cleaning dishes properly
- Not draining
- See more...
Installation Instructions
Kathy from TECUMSEH, MO
My filters had completely clogged up with hard deposits and food left on the dishes after running the dishwasher.
My filters had completely clogged up and had not cleaned my filters at all which was a no-no.I had lots of food left on the dishes after running my dishwasher, so I took bothp filters out and replaced them no tools required. I won’t be using powdered or liquid detergent for my dishwasher anymore only pods and promise to clean my filters once a month, so hopefully that’ll help keep them clean. Very easy replacement even for an old woman.
Read more...
Appliance Type
Related Parts
- Amana Dishwasher Brackets and Flanges
- Amana Dishwasher Caps and Lids
- Amana Dishwasher Dishracks
- Amana Dishwasher Dispensers
- Amana Dishwasher Handles
- Amana Dishwasher Hardware
- Amana Dishwasher Hinges
- Amana Dishwasher Hoses and Tubes
- Amana Dishwasher Latches
- Amana Dishwasher Panels
- Amana Dishwasher Pumps
- Amana Dishwasher Seals and Gaskets
- Amana Dishwasher Spray Arms
- Amana Dishwasher Springs and Shock Absorbers
- Amana Dishwasher Switches
- Amana Dishwasher Wheels and Rollers
Popular Amana Dishwasher Models
Below are the most popular Amana Dishwasher models we have. Enter your model number in the search box to find your model.
- ADB1500AWW
- ADB1500AWB
- ADB1500AWS
- ADB1100AWW5 DISHWASHER
- ADB1400AGW1 DISHWASHER
- ADB3500AWS
- ADB2500AWS
- ADB1200AWS Tall Tub
- ADB1400AGS1 DISHWASHER
- ADB2500AWW
- ADB1200AWW Tall Tub
- ADB2500AWB
- ADB2200AWS
- ADB1100AWS5 DISHWASHER
- ADB1500AWQ
- ADB1100AWW4 DISHWASHER
- ADB3500AWB
- ADB1100AWB5 DISHWASHER
- ADB1100AWW3 UNDERCOUNTER DISHWASHER
- ADB2200AWW
