This is a drive belt for your washing machine. This part spins the basket in your appliance by connecting the drive motor to the drive system. You will need to replace the drive belt if your pumps are not spinning, your washer is not agitating, or you are noticing excess noise and/or a burning smell. This belt is black with six ribbings. To replace this part, you will need a Phillips screwdriver.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your Frigidaire Washer Drive Belt - 6 ribs
Troubleshooting
This part fixes the following symptoms:
Spins slowly | Will not agitate | Burning smell
This part works with the following products:
Washer, Washer Dryer Combo.
Part# 134051000 replaces these:
AP2108082, 916708, 111700354, 131276300
Customer Reviews
Average Rating:
★★★★★
★★★★★
2 Reviews
5.0
Filter By Rating:
5 Stars
2
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
0
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Ezra V - April 23, 2019
Verified Purchase
Part installed and working
All is well again with my 22 year old Gibson washer thanks for keeping the parts available
★★★★★
★★★★★
Jim R - March 15, 2018
Verified Purchase
It fixed my problem.
It worked. Was a touch harder to get onto both pullies than the video shows but it solved the drum not rotating problem during wash or spin. Compared to the old belt it looked to be an inches or two smaller but that's what I needed.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.2 / 5.0, 5 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
WASHER WASN'T SPINNING OUT ANYMORE.
Pulled the back off and it was right there. Hardest part was to get the belt all the way around the drive wheel on the washer tub. Found out that it wasn't just the belt. It is the shock absorbers that probably broke the belt, even though the belt was probably well over 15 years old. The bouncing and banging because of the absorbers being
... Read more bad probably had something to do with the belt eventually breaking. Now, we need to replace the shock absorbers.A big thing to remember about the belt install....clean the drive wheel real good!!!
Read less
Christopher from CHARLEVOIX, MI
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
3 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The only problem was that the drive belt was so tight that it was two inches short from the drive shaft making it very difficult to put on by hand.
I did my best to stretch the belt out and as I wrapped it around the pulley one hand was preventing the belt from slipping off and the other hand had the screwdriver to use as Leverage to stretch and slip the belt on the other side of the pulley. One thing that I saw but didn't try was to use zip ties to temporarily hold the belt in place
... Read more so it didn't slip off that may have helped.
1. replaced (2) shocks, remove bottom cover 2. (1) spring and rib belt, used a wooden block to hold up drum , rolled out ld belt and rolled in new----remove top and rear covers after replaced same ---thanks..
Alvin from Woodside, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set
8 of 14 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door switch wouldn't allow machine to operate
disassembled cabinet to access, repl'ed switch with repl'mt sw. and harness provided. Instructions provided with repl'mt sw. made install very easy.
First I turned off the water and disconnected the hoses. I took off the back panel and unscrewed the 4 bolts holding the motor in place. The grounding screw was impossible to remove, so I had to cut the wire off. Took out motor and disconnected the electrical connector. Put new motor in (ordered new belt, figuring it would need replac
... Read moreing - was still in excellent shape, but replaced it anyway), bolted in the motor (socket set works best on further away bolts, screwdriver for closer ones). Put the belt on the motor first and then pulled it up over the side of the tub and turned the tub to get it around the whole tub - took alittle bit of turning to get it on. Plugged in electrical connector and screwed grounding wire into hole. Replaced back panel and water hoses. Got a bit dirty and sweaty but not too hard to do it yourself, as I am a 48 yr woman and don't usually do this kind of thing.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
4 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Gary
September 12, 2017
I replaced the shocks on my washer and it still makes a loud noise when it's on the high spin cycle the model # is ftf530eso what else could the problem be
For model number FTF530ES0
Hi Gary,
Thank you for your inquiry. You may want to also check your belt and pulley as well. You could also take a look at your spider arm and your rear outer tub to see if those may be the parts that are causing your noise. I hope this helps. Good luck with your repair.
4 people found this helpful.
Was this helpful?
Thank you for voting!
Moises
November 10, 2017
How to fix the belt on the washer
For model number 417-42042100
Hi Moises,
Thank you for your question. We do have a general video that may help you with this installation. Here you are: https://youtu.be/5KFbBuscBVI . Good luck with your repair.
4 people found this helpful.
Was this helpful?
Thank you for voting!
Ben
August 13, 2017
I can feel the motor running but no agitation. Pump runs. Is this a belt problem?
For model number sears washer 417-40042990
Hello Ben, that is a great question. Yes, if the motor is running and everything works but the tub wont agitate or spin it more than likely would be the belt. You can remove the back panel to inspect this. Hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Carl
August 26, 2019
Does this part fit the he machine
For model number WSXH208H1WW
Hi Carl, thank you for your question. It does not. According to your model number I have linked the correct part below for you. Good luck with your repair.
